ഉൽപ്പന്നം കഴിഞ്ഞുview
The Viper 474V is a 4-button remote control designed for use with compatible Viper vehicle security and remote start systems. This remote allows for convenient control of your vehicle's security features, including locking, unlocking, auxiliary functions, and remote start/panic.
Image: Viper 474V 4-Button Remote. This image displays the front of the remote control, featuring four distinct buttons: a lock icon, an unlock icon, an 'AUX' button, and an orange button with a speaker/horn icon. The Viper logo is visible below the buttons, and a metal key ring is attached at the bottom.
സജ്ജീകരണവും പ്രോഗ്രാമിംഗും
To program your Viper 474V remote to your vehicle's security system, follow these steps. Ensure you have located your system's valet switch, typically found under the driver's lower dash or on the driver's side kick panel. The exact procedure may vary slightly depending on whether your Viper system includes a remote start module.
- വാഹനം തയ്യാറാക്കുക: Open the driver's side door.
- ഇഗ്നിഷൻ ഓണാണ്: Insert the key into the ignition and turn it to the "Run" position. Do not start the engine. All dashboard warning lights should illuminate.
- ആക്സസ് പ്രോഗ്രാമിംഗ് മോഡ്:
- With Remote Start Module: Press and release the valet button once. This selects Channel 1.
- Without Remote Start Module: Press and release the valet button seven (7) times. This selects Channel 7.
- Confirm Channel Selection: Press the valet button once more and hold it down. The alarm LED on the dash will flash the same number of times as the selected channel (1 or 7), and the siren (if connected) will chirp to confirm. Continue holding the valet button.
- റിമോട്ട് പ്രോഗ്രാം ചെയ്യുക: While still holding the valet button, press the "Lock" button on your new Viper 474V remote. Hold the "Lock" button until the siren sounds, indicating successful programming.
- പ്രോഗ്രാമിംഗ് മോഡിൽ നിന്ന് പുറത്തുകടക്കുക: Release the "Lock" button on the remote, then release the valet button. Turn the ignition key to the "Off" position and remove it from the vehicle. Close the driver's door.
- റിമോട്ട് പരീക്ഷിക്കുക: Test the new remote by attempting to lock and unlock the vehicle.
Note: If you wish to erase all previously programmed remotes and program only the new one, consult your system's specific installation manual for the master reset procedure, which typically involves a different valet button sequence.
പ്രവർത്തന നിർദ്ദേശങ്ങൾ
The Viper 474V remote features four buttons for controlling your vehicle's security system:
- ലോക്ക് ബട്ടൺ (🔒): Press to arm the security system and lock the vehicle doors.
- Unlock Button (🔓): Press to disarm the security system and unlock the vehicle doors.
- AUX ബട്ടൺ: This button controls an auxiliary function, which can be programmed for various purposes such as trunk release, power windows, or other accessories. Refer to your system's installation manual for the specific function assigned to this button.
- Orange Button (Speaker/Horn Icon): This button typically activates the remote start function (if installed and programmed) or the panic alarm.
- വിദൂര തുടക്കം: Press twice to activate remote engine start.
- പരിഭ്രാന്തി: Press and hold for a few seconds to activate the panic alarm. Press again to deactivate.
Note: Button sensitivity is high. Be mindful when carrying the remote in pockets to avoid unintentional activation of functions like remote start or panic.
മെയിൻ്റനൻസ്
ബാറ്ററി മാറ്റിസ്ഥാപിക്കൽ
The Viper 474V remote is powered by a small battery. If the remote's range decreases significantly or it stops responding, the battery may need replacement. To replace the battery:
- റിമോട്ട് സി ശ്രദ്ധാപൂർവ്വം തുറക്കുകasing. This usually involves prying it open along the seam with a small, flat tool.
- Note the type and orientation of the existing battery.
- Remove the old battery and insert a new one of the same type, ensuring correct polarity.
- റിമോട്ട് സി അടയ്ക്കുകasinഗ്രാം സുരക്ഷിതമായി.
Always dispose of old batteries responsibly according to local regulations.
ട്രബിൾഷൂട്ടിംഗ്
- റിമോട്ട് പ്രതികരിക്കുന്നില്ല:
- ബാറ്ററി പരിശോധിക്കുക. ആവശ്യമെങ്കിൽ മാറ്റിസ്ഥാപിക്കുക.
- Ensure the remote is within range of the vehicle's receiver.
- Re-attempt the programming steps outlined in the "Setup and Programming" section.
- Verify that the valet switch is functioning correctly.
- Unintentional Activations:
- The buttons on the 474V remote are sensitive. Avoid placing the remote in tight pockets or areas where buttons might be accidentally pressed.
- പരിമിത ശ്രേണി:
- റിമോട്ട് ബാറ്ററി മാറ്റിസ്ഥാപിക്കുക.
- Ensure there are no large metallic objects or electronic devices interfering with the signal between the remote and the vehicle.
സ്പെസിഫിക്കേഷനുകൾ
- മോഡൽ നമ്പർ: 474V
- ബ്രാൻഡ്: വൈപ്പർ
- ഉൽപ്പന്ന അളവുകൾ: 8 x 6 x 1.75 ഇഞ്ച്
- ഇനത്തിൻ്റെ ഭാരം: 2.4 ഔൺസ്
- കണക്റ്റിവിറ്റി ടെക്നോളജി: ഇൻഫ്രാറെഡ്
- പ്രത്യേക സവിശേഷത: എർഗണോമിക് ഡിസൈൻ
- അനുയോജ്യമായ ഉപകരണങ്ങൾ: Vehicle Alarm Systems
- പിന്തുണയ്ക്കുന്ന ഉപകരണങ്ങളുടെ പരമാവധി എണ്ണം: 1
വാറൻ്റിയും പിന്തുണയും
For warranty information, technical support, or further assistance with your Viper 474V remote or associated vehicle security system, please refer to the documentation provided with your complete Viper system or contact Directed Electronics Inc., the manufacturer, directly. You can typically find support contact details on the manufacturer's official webസൈറ്റ്.
It is recommended to register your product with the manufacturer, if applicable, to ensure you receive updates and support.