Fiamma Aluminium Wall Brackets 98655-728 Instruction Manual

1. ആമുഖം

This manual provides detailed instructions for the proper installation, operation, and maintenance of the Fiamma Aluminium Wall Brackets, model 98655-728. These brackets are designed to securely hold the support legs of your Fiamma awning when not in use or when additional stability is required. Please read this manual thoroughly before proceeding with installation or use to ensure safety and optimal performance.

2 സുരക്ഷാ വിവരങ്ങൾ

• Always ensure the mounting surface is structurally sound and capable of supporting the brackets and the forces exerted by the awning legs.
• ഇൻസ്റ്റാളേഷൻ സമയത്ത് ഉചിതമായ ഉപകരണങ്ങളും വ്യക്തിഗത സംരക്ഷണ ഉപകരണങ്ങളും ഉപയോഗിക്കുക.
• Verify that no electrical wires, plumbing, or other critical components are behind the drilling locations before making any holes.
• After installation, regularly check the brackets and fasteners for any signs of wear, damage, or loosening.
• Do not overload the brackets or use them for purposes other than securing awning legs.

3. പാക്കേജ് ഉള്ളടക്കം

ഇൻസ്റ്റാളേഷൻ ആരംഭിക്കുന്നതിന് മുമ്പ് എല്ലാ ഘടകങ്ങളും നിലവിലുണ്ടെന്ന് ഉറപ്പാക്കുക:

• 2x Fiamma Aluminium Wall Brackets
• 2x Black Plastic Inserts (for bracket interior)
• 2x Black Plastic Backing Plates
• 2x Metal Spacers/Washers
• 4x മൗണ്ടിംഗ് സ്ക്രൂകൾ

Image 3.1: Contents of the Fiamma Aluminium Wall Brackets package, showing two main brackets, plastic inserts, backing plates, metal washers, and mounting screws.

4. സജ്ജീകരണവും ഇൻസ്റ്റാളേഷനും

Follow these steps for secure installation of your Fiamma Aluminium Wall Brackets:

1. മൗണ്ടിംഗ് ലൊക്കേഷൻ തിരഞ്ഞെടുക്കുക: Select a flat, sturdy surface on your RV or vehicle where the awning legs will be stored. Ensure the location allows for easy access and does not interfere with other components. The brackets should be positioned to accommodate the length and angle of your awning legs.
2. ഉപരിതലം തയ്യാറാക്കുക: Clean the mounting surface thoroughly to remove any dirt, grease, or debris. A clean surface ensures proper adhesion and sealing.
3. ഡ്രില്ലിംഗ് പോയിന്റുകൾ അടയാളപ്പെടുത്തുക: Place one of the black plastic backing plates against the chosen surface. Use a pencil or marker to accurately mark the two drilling points through the holes in the plate. Repeat for the second bracket, ensuring proper spacing for your awning legs.
4. ഡ്രിൽ പൈലറ്റ് ദ്വാരങ്ങൾ: Using an appropriate drill bit size for your mounting screws and surface material, carefully drill pilot holes at the marked locations. Ensure the holes are deep enough for the screws but do not penetrate any internal components.
5. Apply Sealant (Recommended): For RV applications, it is highly recommended to apply a marine-grade or RV-specific sealant around the pilot holes before mounting the brackets. This prevents water ingress and potential damage to your vehicle's structure.
6. Assemble and Mount Brackets:
   • Insert the black plastic insert into the main aluminium bracket.
   • Place a metal spacer/washer over each screw.
   • Align the aluminium bracket (with insert), the black plastic backing plate, and the pilot holes.
   • Insert the screws through the bracket, backing plate, and into the pilot holes.
   • Tighten the screws firmly but do not overtighten, as this can strip the holes or damage the bracket.
7. അന്തിമ പരിശോധന: Once both brackets are installed, gently pull on them to ensure they are securely fastened to the wall.

Image 4.1: Two assembled Fiamma Aluminium Wall Brackets, showing their design for holding awning legs.

5. പ്രവർത്തന നിർദ്ദേശങ്ങൾ

Using the Fiamma Aluminium Wall Brackets is straightforward:

1. To Secure Awning Legs: Gently slide the end of your awning leg into the opening of the wall bracket. The design of the bracket, with its plastic insert, is intended to hold the leg firmly in place. Ensure the leg is fully seated within the bracket.
2. To Release Awning Legs: Simply pull the awning leg out of the bracket. No special release mechanism is required.

Always ensure awning legs are properly secured in the brackets during travel to prevent movement and potential damage.

6. പരിപാലനം

Regular maintenance will prolong the life and effectiveness of your wall brackets:

• വൃത്തിയാക്കൽ: Clean the aluminium brackets periodically with a mild soap and water solution. Avoid abrasive cleaners or solvents that could damage the finish or plastic components.
• പരിശോധന: Annually, or before long trips, inspect the brackets for any signs of corrosion, cracks, or damage. Check that all mounting screws are tight. If any component is damaged, replace the bracket set immediately.
• സീലന്റ് പരിശോധന: If sealant was used during installation, inspect it for cracks or deterioration and reapply if necessary to maintain a watertight seal.

7. പ്രശ്‌നപരിഹാരം

• Awning Leg Does Not Fit Securely:
  • Ensure the correct Fiamma awning leg model is being used with these brackets.
  • Check if the plastic insert is correctly seated within the aluminium bracket.
  • Inspect the awning leg for any deformation that might prevent a snug fit.
• Brackets Feel Loose After Installation:
  • Gently retighten the mounting screws. Do not overtighten.
  • Inspect the mounting surface for any signs of material fatigue or damage. If the surface is compromised, the brackets may need to be relocated or the surface reinforced.
• Water Leakage Around Brackets:
  • This indicates a failure in the sealant applied during installation. Remove the brackets, clean the area, reapply a fresh bead of marine-grade or RV-specific sealant around the pilot holes and under the bracket, then reinstall.

8 സ്പെസിഫിക്കേഷനുകൾ

9. വാറൻ്റിയും പിന്തുണയും

For warranty information or technical support regarding your Fiamma Aluminium Wall Brackets, please refer to the official Fiamma website or contact your authorized Fiamma dealer. Keep your proof of purchase for any warranty claims.