Kadimendium ND0412SA DC-DC Step-up Module

1. ആമുഖം

This manual provides detailed instructions for the Kadimendium ND0412SA DC-DC Step-up Module. This module is designed to convert a lower DC input voltage (2.6V-5.5V) into a higher, stable DC output voltage (selectable 5V, 6V, 9V, or 12V). It is suitable for various applications requiring a boosted power supply, such as battery-powered equipment, LED motors, and low-power electronic devices.

2. സുരക്ഷാ നിർദ്ദേശങ്ങൾ

• Ensure all power sources are disconnected before making any connections to the module.
• Observe correct polarity for input and output connections (V_i, GND, V_o). Incorrect polarity can damage the module and connected devices.
• നിർദ്ദിഷ്ട പരമാവധി ഇൻപുട്ട് വോള്യം കവിയരുത്tage or output current ratings.
• Avoid short circuits on the input or output terminals. While the module has short-circuit protection, prolonged short circuits can cause damage.
• Operate the module within its specified temperature range (-40°C to +85°C).
• Keep the module away from moisture, dust, and corrosive environments.

3. ഉൽപ്പന്നം കഴിഞ്ഞുview

The ND0412SA is a compact and efficient DC-DC boost converter. It features high efficiency (up to 93%) and incorporates multiple protection mechanisms including over current (OCP), over voltage (OVP), short circuit (SCP), and over temperature (OTP) to ensure reliable operation and extend the lifespan of the power supply.

ചിത്രം 3.1: മുകളിൽ view of the ND0412SA module, displaying its compact design and main components.

The module's input terminals are labeled V_i (ഇൻപുട്ട് വോളിയംtage) and GND (Ground). The output terminals are labeled V_o (ഔട്ട്പുട്ട് വോളിയംtage) and GND. The bottom side of the module features solder pads for selecting the desired output voltage.

ചിത്രം 3.2: താഴെ view of the ND0412SA module, showing the output voltage selection pads.

4. സജ്ജീകരണം

Follow these steps to set up your ND0412SA module:

1. Putട്ട്പുട്ട് വോളിയംtagഇ തിരഞ്ഞെടുക്കൽ: Before connecting power, select your desired output voltage (5V, 6V, 9V, or 12V) by bridging the corresponding solder pads on the bottom of the module (refer to Figure 3.2). For example, to set the output to 12V, bridge the pad labeled '12V'. If no pads are bridged, the module may default to a specific voltage or operate unpredictably.
2. ഇൻപുട്ട് കണക്ഷൻ: Connect your DC input power source to the V_i and GND input terminals. Ensure the input voltage is within the 2.6V to 5.5V range.
3. ഔട്ട്പുട്ട് കണക്ഷൻ: Connect your load to the V_o and GND output terminals.
4. Advanced Output Voltage and Current Limit Adjustment (Optional): For custom output voltages or current limits, the module allows adjustment via external resistors R1 and R3. This requires soldering and precise resistor values. Refer to Figure 4.1 for details.
   • Putട്ട്പുട്ട് വോളിയംtage (R1): The R1 resistor sets the output voltage. The formula is R1(KΩ) = 10 * (Vout / 0.6 - 1).
   • Current Limit (R3): The R3 resistor programs the peak switch current. The resistor value should be between 10kΩ and 100kΩ. The current limit will be set from 2.5A to 0.5A. The formula is I_in = 48000 / R3.

Figure 4.1: Diagram for R1 (output voltage) and R3 (current limit) resistor settings.

5. പ്രവർത്തന നിർദ്ദേശങ്ങൾ

Once the module is correctly wired and the output voltage is selected, apply power to the input terminals. The module will automatically boost the input voltage to the selected output voltage. ഔട്ട്‌പുട്ട് വോളിയം നിരീക്ഷിക്കുകtage and current to ensure it meets your application's requirements and stays within the module's specifications.

6. പരിപാലനം

• മൊഡ്യൂൾ വൃത്തിയായും പൊടിയും അവശിഷ്ടങ്ങളും ഇല്ലാതെ സൂക്ഷിക്കുക.
• Ensure adequate ventilation, especially when operating at higher loads, to prevent overheating.
• Regularly inspect connections for looseness or corrosion.
• Avoid physical shock or excessive vibration to the module.

7. പ്രശ്‌നപരിഹാരം

• ഔട്ട്പുട്ട് വോളിയം ഇല്ലtage:
  • ഇൻപുട്ട് വോളിയം പരിശോധിക്കുകtage to ensure it is within the 2.6V-5.5V range.
  • Verify input and output connections for correct polarity and secure contact.
  • ഔട്ട്പുട്ട് വോളിയം ഉറപ്പാക്കുകtage selection pads are correctly bridged.
  • Check for any short circuits on the output. The module's SCP may have activated.
• തെറ്റായ ഔട്ട്‌പുട്ട് വോളിയംtage:
  • Re-verify the output voltage selection pads.
  • If using custom R1 adjustment, double-check resistor value and soldering.
• മൊഡ്യൂൾ അമിത ചൂടാക്കൽ:
  • Reduce the load connected to the output.
  • Ensure proper ventilation around the module.
  • ഇൻപുട്ട് വോളിയം പരിശോധിക്കുകtage is too low, causing the module to draw excessive current.
• ഇടയ്ക്കിടെയുള്ള പ്രവർത്തനം:
  • Check for loose connections or poor soldering.
  • Ensure the module is not exposed to excessive electromagnetic interference.

8 സ്പെസിഫിക്കേഷനുകൾ

Typical Output Current (Reference Only):

9. വാറൻ്റിയും പിന്തുണയും

For warranty information or technical support, please refer to the product's purchase documentation or contact the retailer. Keep your proof of purchase for any warranty claims.