Directed Electronics Plug & Play Remote Starter with T-Harness

ആമുഖം

This manual provides comprehensive instructions for the installation and operation of your Directed Electronics Plug & Play Remote Starter with T-Harness. This system is designed for select Ford vehicles manufactured between 2009 and 2016. It features a no-cut, no-splice T-harness for an OEM-like installation and is compatible with both manual transmission modes and gas/diesel engines. The module comes pre-loaded with Firmware 800.FORD6.

പ്രധാന കുറിപ്പ്: Professional installation is recommended. Some vehicles may require additional parts not included in this package. Please confirm compatibility with your vehicle prior to installation.

സുരക്ഷാ വിവരങ്ങൾ

• ഇൻസ്റ്റാളേഷൻ ആരംഭിക്കുന്നതിന് മുമ്പ് വാഹനം പാർക്കിംഗ് ബ്രേക്ക് ഇട്ട് നിരപ്പായ പ്രതലത്തിൽ പാർക്ക് ചെയ്തിട്ടുണ്ടെന്ന് ഉറപ്പാക്കുക.
• വൈദ്യുതാഘാതമോ വാഹനത്തിന്റെ വൈദ്യുത സംവിധാനത്തിന് കേടുപാടുകളോ ഉണ്ടാകാതിരിക്കാൻ, ഏതെങ്കിലും വൈദ്യുത ജോലി ചെയ്യുന്നതിന് മുമ്പ് വാഹനത്തിന്റെ ബാറ്ററി വിച്ഛേദിക്കുക.
• സുരക്ഷാ ഗ്ലാസുകളും കയ്യുറകളും പോലുള്ള ഉചിതമായ വ്യക്തിഗത സംരക്ഷണ ഉപകരണങ്ങൾ എപ്പോഴും ധരിക്കുക.
• Verify all connections are secure and correctly routed to prevent interference with vehicle operation.
• Do not attempt to start the vehicle with the remote starter if any warning lights are illuminated on the dashboard, or if there are any unusual noises or smells.
• Keep children and pets away from the vehicle during remote start operation.

പാക്കേജ് ഉള്ളടക്കം

Verify all items are present before beginning installation:

• Directed Electronics Remote Starter Module
• T-Harness (no cut, no splice)
• Installation Guide (physical or digital)

Image: The remote starter module, T-harness, and product packaging. The module is a black rectangular device, and the T-harness consists of various wires and connectors designed for plug-and-play installation.

ഇൻസ്റ്റലേഷൻ ഗൈഡ്

Follow these steps carefully for proper installation. Refer to the provided videos for visual guidance.

Step 1: Access the OBD-II Port and Steering Column

Locate the OBD-II port, typically found under the dashboard on the driver's side. You may need to remove trim panels around the steering column to access the necessary wiring harnesses.

Step 2: Connect the T-Harness

The T-harness is designed for plug-and-play installation. Disconnect the existing harness from the vehicle's OBD-II port or gateway module, then connect the T-harness in-line. Ensure all connections are firmly seated.

Step 3: Connect the Remote Starter Module

Connect the T-harness to the remote starter module. Ensure the module is securely connected to the harness.

Step 4: Module Programming

The module requires programming to synchronize with your vehicle. Follow the specific programming steps outlined in the detailed installation guide provided with your product. This typically involves pressing a button on the module while cycling the vehicle's ignition.

General Programming Sequence:

1. Press and hold the programming button on the module.
2. Connect the black connector to the module while holding the button.
3. Release the button when the blue LED is momentarily lit.
4. Connect the white connector to the module.
5. Insert the vehicle key into the ignition (do not start the engine).
6. Turn the ignition to the ON position. The module's LEDs will indicate programming status (e.g., blue LED turns off, red and yellow LEDs turn on).
7. Wait for the blue LED to flash, then turn the ignition OFF. All LEDs should turn off.
8. Turn the ignition ON again. The yellow LED should come on.
9. Wait 5 seconds, then turn the ignition OFF. All LEDs should go off.
10. മൊഡ്യൂൾ ഇപ്പോൾ പ്രോഗ്രാം ചെയ്തു.

പ്രവർത്തന നിർദ്ദേശങ്ങൾ

Once installed and programmed, your remote starter can be operated using your vehicle's factory key fob.

റിമോട്ട് സ്റ്റാർട്ട് സീക്വൻസ്

To remote start your vehicle, press the LOCK button on your factory key fob three times in quick succession (LOCK, LOCK, LOCK). The vehicle's engine should start.

Remote Stop Sequence

To turn off the engine after a remote start, press the LOCK button on your factory key fob three times in quick succession (LOCK, LOCK, LOCK) again, or simply press the brake pedal inside the vehicle.

"No Honk" Programming (if applicable)

Some models allow for a "No Honk" remote start/stop feature. Refer to the video below for programming instructions specific to select KR-RS models.

മെയിൻ്റനൻസ്

The Directed Electronics Remote Starter is designed for maintenance-free operation. Ensure all connections remain secure and free from moisture or debris. Periodically check the wiring for any signs of wear or damage.

ട്രബിൾഷൂട്ടിംഗ്

• Remote starter does not activate:
  • Ensure all doors, hood, and tailgate are closed.
  • Verify the vehicle's battery is charged.
  • Re-check all T-harness connections.
  • Confirm the module was programmed correctly. Repeat the programming steps if necessary.
• Vehicle starts but immediately shuts off:
  • This may indicate an issue with the module's programming or vehicle compatibility. Refer to the detailed installation guide or contact support.
• അപ്രതീക്ഷിത പെരുമാറ്റം:
  • If the system exhibits unexpected behavior, disconnect the module and contact technical support.

സ്പെസിഫിക്കേഷനുകൾ

വാറൻ്റിയും പിന്തുണയും

For warranty information, technical support, or to confirm vehicle compatibility, please contact Directed Electronics customer service or refer to the official product website. It is recommended to reflash the firmware prior to installation for optimal performance.

Note: Some vehicles may require extra parts which are not included and sold separately.