1. ആമുഖം
This user manual provides essential information for the installation, operation, maintenance, and troubleshooting of the Bogist C1 Pro Electric Scooter Controller Motherboard. This component is specifically designed for the Bogist C1 Pro escooter, ensuring optimal performance and compatibility. Please read this manual thoroughly before attempting any installation or maintenance.
ചിത്രം 1: മുൻഭാഗം view of the Bogist C1 Pro Electric Scooter Controller, showing its silver aluminum casing and the YAMTECH logo.
2 സുരക്ഷാ വിവരങ്ങൾ
Always prioritize safety when handling electronic components. Failure to follow these guidelines may result in injury, damage to the product, or voiding of the warranty.
- പവർ വിച്ഛേദിക്കുക: Always ensure the scooter's battery is disconnected before installing, removing, or servicing the controller.
- പ്രൊഫഷണൽ ഇൻസ്റ്റാളേഷൻ ശുപാർശ ചെയ്യുന്നു: If you are not familiar with electrical components or scooter repair, seek assistance from a qualified technician.
- ശ്രദ്ധയോടെ കൈകാര്യം ചെയ്യുക: Electronic components are sensitive. Avoid dropping the controller or exposing it to excessive force.
- ഈർപ്പം സംരക്ഷണം: Keep the controller dry. Exposure to water or excessive humidity can cause damage.
- ശരിയായ ധ്രുവീകരണം: Ensure all connections are made with correct polarity to prevent short circuits and damage.
- വെൻ്റിലേഷൻ: Ensure the controller is installed in a location with adequate ventilation to prevent overheating.
3. സജ്ജീകരണവും ഇൻസ്റ്റാളേഷനും
This section outlines the general steps for replacing or installing the Bogist C1 Pro Electric Scooter Controller. Specific wiring diagrams for your scooter model may be required and are typically found in the scooter's main service manual.
3.1 തയ്യാറാക്കൽ
- Ensure the scooter is turned off and the battery is completely disconnected.
- Gather necessary tools: screwdrivers, wire cutters/strippers (if needed), electrical tape, and zip ties.
- Locate the existing controller within your Bogist C1 Pro escooter. It is typically housed in a protective compartment.
3.2 Controller Replacement/Installation Steps
- Carefully disconnect all wires from the old controller, noting the position and color of each connection. Taking photos before disconnecting can be very helpful.
- പഴയ കൺട്രോളർ അതിന്റെ മൗണ്ടിംഗിൽ നിന്ന് നീക്കം ചെയ്യുക.
- Position the new Bogist C1 Pro Controller in the same location.
- Connect the wires from the scooter to the corresponding ports on the new controller. Refer to the labels on the controller and your scooter's wiring diagram. Common connections include:
- ബാറ്ററി പവർ: Thick red (positive) and black (negative) wires.
- മോട്ടോർ വയറുകൾ: Typically three thick wires (e.g., yellow, green, blue) for the motor phases.
- Hall Sensor Wires: Thinner wires (e.g., red, black, yellow, green, blue) for motor position sensing.
- ത്രോട്ടിൽ: Wires for speed control.
- ബ്രേക്ക് ലിവറുകൾ: Wires for brake cut-off.
- Display/Dashboard: Wires for communication with the scooter's display.
- ലൈറ്റുകൾ: Wires for headlights/taillights.
ചിത്രം 2: വിശദമായി view of the Bogist C1 Pro Electric Scooter Controller, highlighting the various colored wires and connectors, along with the technical specifications label on the casing.
Figure 3: Close-up of the various connectors and wiring harnesses extending from the Bogist C1 Pro Electric Scooter Controller, showing different plug types for various scooter components.
- Once all connections are secure, carefully arrange the wires to avoid pinching or damage when closing the compartment.
- Secure the controller in its mounting.
- Reconnect the scooter's battery.
- Perform a functional test (see Operating section).
4. Operating and Functional Test
After installation, it is crucial to perform a functional test to ensure the controller is working correctly and safely. This controller is an internal component; its "operation" is reflected in the scooter's functionality.
- With the battery reconnected, turn on the scooter's power switch.
- Check the scooter's display (if applicable) to ensure it powers on and shows correct information (e.g., battery level).
- Test the throttle: Gently apply the throttle while the scooter is on its kickstand or lifted, ensuring the wheel spins smoothly.
- Test the brakes: Engage the brake levers to ensure the motor cuts off and the brakes activate correctly.
- Test lights and other accessories connected through the controller.
- If any function does not work as expected, immediately disconnect power and refer to the Troubleshooting section.
5. പരിപാലനം
The Bogist C1 Pro Electric Scooter Controller is designed for durability and requires minimal maintenance. However, periodic checks can extend its lifespan and ensure reliable performance.
- വൃത്തിയായും ഉണങ്ങിയും സൂക്ഷിക്കുക: Regularly inspect the controller compartment for dust, dirt, or moisture. Clean with a dry, soft cloth if necessary.
- കണക്ഷനുകൾ പരിശോധിക്കുക: Periodically (e.g., every 6 months) inspect all wire connections to ensure they are secure and free from corrosion. Loose connections can lead to intermittent issues or damage.
- അമിതമായി ചൂടാക്കുന്നത് ഒഴിവാക്കുക: Ensure the controller's housing is not obstructed, allowing for proper heat dissipation. Avoid operating the scooter in extreme heat for prolonged periods.
- ശാരീരിക പരിശോധന: Look for any signs of physical damage, such as dents, cracks, or frayed wires. Address any damage promptly.
6. പ്രശ്നപരിഹാരം
This section provides solutions to common issues you might encounter with the Bogist C1 Pro Electric Scooter Controller. Always disconnect power before attempting any internal inspection or repair.
| പ്രശ്നം | സാധ്യമായ കാരണം | പരിഹാരം |
|---|---|---|
| സ്കൂട്ടർ ഓണാക്കുന്നില്ല. | Loose battery connection, faulty power switch, dead battery, or controller issue. | Check battery connection and charge. Verify power switch functionality. If other components work, controller may be faulty. |
| Motor does not spin or spins intermittently. | Loose motor phase wires, faulty Hall sensors, throttle issue, or controller malfunction. | Check all motor and Hall sensor connections. Test throttle functionality. If connections are good, controller may need replacement. |
| Brakes do not cut off motor power. | Loose brake lever sensor wires, faulty brake lever, or controller issue. | Inspect brake lever wiring. Ensure brake levers are not stuck. |
| Display/Dashboard not working. | Loose display connection, faulty display, or controller communication issue. | Check display cable connection to the controller. |
| Controller gets excessively hot. | Overload, poor ventilation, or internal short circuit. | Ensure proper ventilation. Avoid overloading the scooter. If heat persists, controller may be faulty. |
If the problem persists after attempting these solutions, it is recommended to consult a professional scooter repair service or contact customer support.
7 സ്പെസിഫിക്കേഷനുകൾ
Key technical specifications for the Bogist C1 Pro Electric Scooter Controller Motherboard (Model: YAM-1214-06).
| ഫീച്ചർ | വിശദാംശങ്ങൾ |
|---|---|
| മോഡലിൻ്റെ പേര് | YAM-1214-06 |
| ബ്രാൻഡ് | ജനറിക് |
| അനുയോജ്യത | Only For Bogist C1 Pro escooter |
| മെറ്റീരിയൽ | അലുമിനിയം |
| നിറം | വെള്ളി |
| ഇനത്തിൻ്റെ പാക്കേജ് അളവുകൾ (L x W x H) | 4.21 x 4.13 x 2.05 ഇഞ്ച് |
| പാക്കേജ് ഭാരം | 0.05 കിലോഗ്രാം |
| നിർമ്മാതാവ് | YAMTECH |
8. വാറൻ്റിയും പിന്തുണയും
8.1 വാറൻ്റി വിവരങ്ങൾ
This Bogist C1 Pro Electric Scooter Controller Motherboard comes with a 90-Days Warranty from the date of purchase. This warranty covers manufacturing defects under normal use. It does not cover damage resulting from improper installation, misuse, accidents, unauthorized modifications, or exposure to extreme conditions.
8.2 ഉപഭോക്തൃ പിന്തുണ
For technical assistance, warranty claims, or any questions regarding your Bogist C1 Pro Electric Scooter Controller, please contact the manufacturer or seller through the platform where the product was purchased. Please have your purchase details and product model number (YAM-1214-06) ready when contacting support.
പൊതുവായ അന്വേഷണങ്ങൾക്ക്, നിങ്ങൾക്ക് സന്ദർശിക്കാവുന്നതാണ് ആമസോണിലെ ഉൽപ്പന്ന പേജ്.
