ZLL Beast SG116 MAX Brushless 1/16 Scale 4WD RC Truck Instruction Manual

ആമുഖം

This manual provides essential instructions for the safe and effective operation, maintenance, and setup of your ZLL Beast SG116 MAX Brushless 1/16 Scale 4WD RC Truck. Please read this manual thoroughly before first use and retain it for future reference.

Image: The ZLL Beast SG116 MAX RC Truck with its remote control, battery, charger, and tools.

സുരക്ഷാ വിവരങ്ങൾ

WARNING: Not suitable for children under 3 years due to small parts.

• Always operate the RC truck in open areas, away from people, pets, and obstacles.
• Avoid operating near public roads, water bodies, or electrical lines.
• Ensure the battery is fully charged and securely installed before operation.
• Do not touch moving parts during operation to prevent injury.
• Always turn off the RC truck and remote control when not in use.
• Store the RC truck and accessories in a cool, dry place.

ബോക്സിൽ എന്താണുള്ളത്

അൺബോക്സ് ചെയ്യുമ്പോൾ, താഴെ ലിസ്റ്റ് ചെയ്തിരിക്കുന്ന എല്ലാ ഘടകങ്ങളും ഉണ്ടെന്ന് ഉറപ്പാക്കുക:

• SG116MAX TRUCK
• Charging Cable and 7.4V Li-Ion Battery
• Screwdriver and Tool Set
• ഉൽപ്പന്ന മാനുവൽ
• റിമോട്ട് കൺട്രോൾ

സജ്ജീകരണ ഗൈഡ്

1. ബാറ്ററി ഇൻസ്റ്റാളേഷനും ചാർജിംഗും

1. ആർസി ട്രക്കിന്റെ അടിഭാഗത്ത് ബാറ്ററി കമ്പാർട്ട്മെന്റ് കണ്ടെത്തുക.
2. Carefully open the compartment and insert the provided 7.4V Li-Ion battery, ensuring correct polarity.
3. ബാറ്ററി കമ്പാർട്ട്മെൻ്റ് സുരക്ഷിതമായി അടയ്ക്കുക.
4. To charge the battery, connect the charging cable to the battery and a compatible USB power source. The charging indicator will show the charging status.
5. Allow approximately 1 hour and 30 minutes for a full charge.

2. റിമോട്ട് കൺട്രോൾ തയ്യാറാക്കൽ

1. Install 3x AA batteries (not included) into the remote control's battery compartment.
2. Turn on the remote control using the power switch.
3. Turn on the RC truck. The remote control and truck should automatically pair. If not, refer to the troubleshooting section.

ചിത്രം: വിശദമായത് view of the 2.4GHz remote control for the SG116 MAX.

Image: The remote control highlighting the three-speed regulation switch.

3. Wheelie Bar Attachment (Optional)

The wheelie bar can be attached to the rear of the truck to prevent it from flipping over during high-speed acceleration. Ensure the mounting points are aligned and secure the bar with the provided screws. Note that the mounting points may rotate, requiring careful alignment during installation.

പ്രവർത്തന നിർദ്ദേശങ്ങൾ

1. അടിസ്ഥാന നിയന്ത്രണങ്ങൾ

• സ്റ്റിയറിംഗ് വീൽ: Turn left or right to control the direction of the truck.
• Gas Pedal (Trigger): Pull to accelerate forward, push to brake or reverse. The truck features full proportional steering and throttle for precise control.
• സ്പീഡ് മോഡുകൾ: Use the switch on the remote to select between Low, Medium, and High speed modes. This allows adjustment for different skill levels and terrains.
• ഹെഡ്ലൈറ്റുകൾ: The truck is equipped with headlights for visibility. Refer to the remote control diagram for the light switch.

2. ഡ്രൈവിംഗ് നുറുങ്ങുകൾ

• Start in Low speed mode to familiarize yourself with the controls.
• The 4WD system and all-terrain non-slip vacuum tires provide excellent traction on various surfaces including mud, snow, sand, grass, and rough trails.
• The powerful 4000kv 2847 brushless motor allows for speeds up to 60km/h with the included 7.4v Li-ion battery. With a 2S or 3S Lipo battery (not included), speeds can exceed 80km/h.
• Be mindful of battery heat when using 3S batteries, as this can stress the ESC.
• The active use time is approximately 25-30 minutes, depending on the selected speed mode.

Image: The ZLL Beast SG116 MAX demonstrating its off-road capability on gravel.

3. ഔദ്യോഗിക ഉൽപ്പന്ന വീഡിയോ

മെയിൻ്റനൻസ്

1. ജനറൽ കെയർ

• After each use, clean the truck to remove dirt, dust, and debris. A soft brush or cloth can be used.
• The intelligent waterproof ESC provides protection against water splashes, but avoid submerging the vehicle.
• Regularly inspect the tires for wear and tear.

2. ഘടക പരിശോധന

• Check for any loose screws or connections and tighten them as necessary.
• Inspect the metal differentials, CVD drive shafts, and spring shock absorbers for any damage. These metal upgrades contribute to the truck's durability.
• The high-strength front bumper and rear swing arm are designed to protect against collisions, but inspect them for cracks or damage after impacts.

ചിത്രം: അടിവശം view of the RC truck, highlighting the chassis and drivetrain components.

Image: Close-up of the metal differential, a key durable component.

Image: The spring-loaded shock absorbers providing suspension for rough terrain.

ട്രബിൾഷൂട്ടിംഗ്

സ്പെസിഫിക്കേഷനുകൾ

വാറൻ്റിയും പിന്തുണയും

For warranty information, technical support, or replacement parts, please refer to the contact details provided with your purchase documentation or visit the official ZLL webസൈറ്റ്. വാറന്റി ക്ലെയിമുകൾക്കായി നിങ്ങളുടെ വാങ്ങലിന്റെ തെളിവ് സൂക്ഷിക്കുക.