ഇൻസ്ട്രക്ഷൻ മാനുവൽ

1. ആമുഖം

This instruction manual provides detailed information for the installation, maintenance, and troubleshooting of the replacement accessory kit compatible with Xiaomi Robot Vacuum S20 and D106 models. This kit is designed to maintain the optimal performance of your robot vacuum cleaner.

ചിത്രം 1: അനുയോജ്യത അവസാനിച്ചുview for Xiaomi Robot Vacuum S20 and D106.

2. ഉൽപ്പന്ന ഘടകങ്ങൾ

The replacement kit includes the following components:

• 2 x Main Brushes (Roller Brushes)
• 6 x സൈഡ് ബ്രഷുകൾ
• 6 x HEPA Filters
• 6 x മോപ്പ് തുണികൾ

ചിത്രം 2: ഓവർview of all included replacement parts.

3. ഇൻസ്റ്റാളേഷൻ ഗൈഡ്

Before installing any new components, ensure your robot vacuum cleaner is powered off and unplugged from its charging base.

3.1 Main Brush Installation

1. Turn the robot vacuum cleaner upside down.
2. Locate the main brush cover, usually secured by latches or screws.
3. കവർ തുറക്കുക അല്ലെങ്കിൽ അഴിക്കുക, പഴയ പ്രധാന ബ്രഷ് നീക്കം ചെയ്യുക.
4. Clean any debris from the brush compartment.
5. Insert the new main brush, ensuring the ends align with the slots.
6. Close the main brush cover and secure it.

Figure 3: Main brush component.

3.2 Side Brush Installation

1. Turn the robot vacuum cleaner upside down.
2. Locate the side brushes. They are typically held by a single screw.
3. Unscrew and remove the old side brush.
4. Align the new side brush with the screw hole.
5. Secure the new side brush with the screw.

Figure 4: Side brush components.

3.3 HEPA Filter Installation

1. Open the dustbin compartment of your robot vacuum.
2. ഡസ്റ്റ്ബിൻ നീക്കം ചെയ്യുക.
3. Locate the filter within the dustbin and remove the old HEPA filter.
4. Clean the dustbin thoroughly.
5. Insert the new HEPA filter into the designated slot in the dustbin.
6. Reinstall the dustbin into the robot vacuum.

Figure 5: HEPA filter components.

3.4 Mop Cloth Installation

1. Locate the mop cloth attachment on your robot vacuum. This may be a separate water tank or a dedicated mop plate.
2. Remove the old mop cloth, typically attached via Velcro or a sliding mechanism.
3. Attach the new mop cloth, ensuring it is securely fastened and covers the entire mop area.
4. If applicable, fill the water tank before reattaching the mop module to the robot.

Figure 6: Mop cloth component.

4. പ്രവർത്തന പരിഗണനകൾ

Once the replacement parts are installed, your robot vacuum cleaner should operate as usual. It is recommended to run a test cleaning cycle to ensure all components are functioning correctly. The new parts are designed to restore optimal cleaning performance, including efficient dust removal and effective floor mopping.

5. പരിപാലനം

Regular maintenance of these replacement parts will extend their lifespan and ensure consistent cleaning performance.

• പ്രധാന ബ്രഷ്: Periodically remove the main brush and clean any tangled hair or debris. The main brush is designed to be easily removable for cleaning.
• സൈഡ് ബ്രഷുകൾ: Check side brushes for wear or damage. Remove any hair or debris that may have accumulated around the base. Replace if bristles are bent or worn.
• HEPA ഫിൽട്ടർ: Tap the filter gently to remove dust. The HEPA filters can be washed with water and air-dried for reuse. Ensure the filter is completely dry before reinserting it into the dustbin.
• Mop Cloth: After each mopping cycle, remove the mop cloth and wash it. It can be hand-washed or machine-washed. Allow it to air dry completely before reattaching.

6. പ്രശ്‌നപരിഹാരം

If you encounter issues after replacing components, consider the following:

• കുറഞ്ഞ ക്ലീനിംഗ് പ്രകടനം: Ensure all brushes are installed correctly and free from obstructions. Check if the HEPA filter is clean and properly seated.
• അസാധാരണമായ ശബ്ദങ്ങൾ: Verify that the main brush and side brushes are securely installed and not obstructed by foreign objects.
• Mop Not Wetting Floor: Ensure the mop cloth is properly attached and the water tank (if applicable) is filled. Check for any blockages in the water dispensing mechanism of your robot vacuum.
• ചേരാത്ത ഭാഗങ്ങൾ: Double-check that your robot vacuum model is indeed Xiaomi S20 or D106. These parts are specifically designed for these models.

7 സ്പെസിഫിക്കേഷനുകൾ

Figure 7: Component dimensions.

മൊത്തം കിറ്റ് ഭാരം: ഏകദേശം 7.2 ഔൺസ് (204 ഗ്രാം)

8. വാറൻ്റിയും പിന്തുണയും

All products are tested before shipping to ensure quality. This product is a compatible spare part and not an original Xiaomi product. For any inquiries or support regarding this replacement kit, please refer to the seller's contact information on the platform where the purchase was made.