ആമുഖം
Thank you for choosing the Kienzle Model 14987 Digital Radio-Controlled Alarm Clock. This device combines precise timekeeping with practical features such as two adjustable alarms, a snooze function, and an indoor temperature display. Its radio-controlled (DCF) functionality ensures accurate time synchronization. This manual provides detailed instructions for setup, operation, and maintenance to ensure optimal performance of your alarm clock.
ചിത്രം 1: Kienzle Model 14987 Digital Radio-Controlled Alarm Clock in a living room setting.
സജ്ജമാക്കുക
1. ബാറ്ററി ഇൻസ്റ്റാളേഷൻ
The alarm clock operates on two AAA/LR03 batteries (not included). Follow these steps to install them:
- യൂണിറ്റിന്റെ പിൻഭാഗത്ത് ബാറ്ററി കമ്പാർട്ട്മെന്റ് കവർ കണ്ടെത്തുക.
- കമ്പാർട്ട്മെന്റ് തുറക്കാൻ കവർ താഴേക്ക് സ്ലൈഡ് ചെയ്യുക.
- Insert two AAA/LR03 batteries, ensuring the correct polarity (+ and -) as indicated inside the compartment.
- സുരക്ഷിതമായി ക്ലിക്ക് ചെയ്യുന്നതുവരെ ബാറ്ററി കമ്പാർട്ട്മെന്റ് കവർ തിരികെ സ്ഥലത്തേക്ക് സ്ലൈഡുചെയ്ത് മാറ്റിസ്ഥാപിക്കുക.
ചിത്രം 2: Battery compartment with two AAA battery slots.
2. Initial Power-On and DCF Signal Reception
Upon battery installation, the clock will automatically power on and begin searching for the DCF radio signal. This process may take several minutes. During this time, a signal icon will typically flash on the display.
- Place the clock near a window for better signal reception, away from electronic devices that may cause interference.
- Once the signal is successfully received, the time will be automatically set, and the signal icon will appear steadily on the display.
- If the signal is not received within 10 minutes, the clock will proceed with default settings. You may need to manually set the time or try relocating the clock.
ചിത്രം 3: Front display of the alarm clock showing time and other information.
പ്രവർത്തന നിർദ്ദേശങ്ങൾ
The Kienzle Model 14987 features four touch buttons for easy operation. These buttons are typically located on the front panel below the display.
ചിത്രം 4: Close-up of the alarm clock display and touch buttons.
1. ബട്ടൺ പ്രവർത്തനങ്ങൾ
- Leftmost Button (e.g., "/⚙️"): Typically used for settings mode or switching display information.
- Second Button (e.g., "⏰"): Used for alarm settings.
- Third Button (e.g., "+/📶"): Used to increase values during settings or manually initiate DCF signal search.
- Rightmost Button (e.g., "-"): Used to decrease values during settings.
2. Setting the Time (Manual)
While the DCF signal automatically sets the time, you can manually adjust it if needed or if the signal is unavailable.
- അമർത്തിപ്പിടിക്കുക Leftmost Button (Settings/Mode) for a few seconds until the time display starts flashing.
- ഉപയോഗിക്കുക "+" ഒപ്പം "-" മണിക്കൂർ ക്രമീകരിക്കാനുള്ള ബട്ടണുകൾ.
- അമർത്തുക Leftmost Button വീണ്ടും മിനിറ്റുകളിലേക്ക് നീക്കുക, തുടർന്ന് ക്രമീകരിക്കുക "+" ഒപ്പം "-".
- അമർത്തുന്നത് തുടരുക Leftmost Button to cycle through other settings like 12/24-hour format, year, month, and day.
- അമർത്തുക Leftmost Button one last time or wait a few seconds for the settings to save and exit.
3. അലാറങ്ങൾ സജ്ജമാക്കുന്നു
The clock features two independent alarms: one for weekdays (Monday-Friday) and one for weekends (Saturday-Sunday).
- അമർത്തുക Alarm Button (⏰) ഒരിക്കൽ view Alarm 1 (AL1) time.
- അമർത്തിപ്പിടിക്കുക Alarm Button (⏰) for a few seconds until the AL1 time starts flashing.
- ഉപയോഗിക്കുക "+" ഒപ്പം "-" buttons to set the desired hour for Alarm 1.
- അമർത്തുക Alarm Button (⏰) വീണ്ടും മിനിറ്റുകളിലേക്ക് നീക്കുക, തുടർന്ന് ക്രമീകരിക്കുക "+" ഒപ്പം "-".
- അമർത്തുക Alarm Button (⏰) once more to confirm and activate Alarm 1. An alarm icon will appear on the display.
- Repeat the process for Alarm 2 (AL2) by pressing the Alarm Button (⏰) രണ്ടുതവണ വരെ view AL2, then press and hold to set.
ഒരു അലാറം സജീവമാക്കാനോ നിർജ്ജീവമാക്കാനോ, അമർത്തുക Alarm Button (⏰) repeatedly until the desired alarm (AL1 or AL2) is shown, then press the "+" button to toggle it on or off. An active alarm will show its respective icon (e.g., AL1, AL2) on the display.
4. സ്നൂസ് ഫംഗ്ഷൻ
When an alarm sounds, touch the top bar of the clock or the designated snooze area (if applicable) to activate the snooze function. The alarm will temporarily stop and sound again after approximately 5-10 minutes (duration may vary). To fully turn off the alarm, press any other button on the front panel.
5. താപനില പ്രദർശനം
The clock continuously measures and displays the indoor temperature. You can switch between Celsius (°C) and Fahrenheit (°F) by pressing the Leftmost Button (Settings/Mode) briefly when not in setting mode, or as indicated in the display cycle.
6. ബാക്ക്ലൈറ്റ്
The display features a backlight for improved visibility in low light conditions. To activate the backlight, briefly touch the top bar of the clock or the designated backlight/snooze area. The backlight will illuminate for a few seconds and then turn off automatically to conserve battery life.
ചിത്രം 5: Alarm clock display with activated backlight.
മെയിൻ്റനൻസ്
1. വൃത്തിയാക്കൽ
To clean the alarm clock, use a soft, dry cloth. Do not use abrasive cleaners, solvents, or chemical sprays, as these can damage the display or casing. Avoid getting moisture into the unit.
2. ബാറ്ററി മാറ്റിസ്ഥാപിക്കൽ
When the display becomes dim or the clock functions erratically, it is time to replace the batteries. Follow the battery installation steps outlined in the "Setup" section. Always replace both batteries at the same time with new AAA/LR03 batteries. Dispose of old batteries responsibly according to local regulations.
ട്രബിൾഷൂട്ടിംഗ്
| പ്രശ്നം | സാധ്യമായ കാരണം | പരിഹാരം |
|---|---|---|
| ഡിസ്പ്ലേ ശൂന്യമോ മങ്ങിയതോ ആണ്. | കുറഞ്ഞതോ കാലഹരണപ്പെട്ടതോ ആയ ബാറ്ററികൾ. | Replace with fresh AAA/LR03 batteries. |
| സമയം തെറ്റാണ് അല്ലെങ്കിൽ യാന്ത്രികമായി സജ്ജീകരിക്കുന്നില്ല. | Weak or no DCF radio signal reception. Interference from other electronics. | Relocate the clock closer to a window or away from electronic devices. Manually set the time if the signal cannot be received. |
| അലാറം മുഴങ്ങുന്നില്ല. | Alarm is not activated. Incorrect alarm time set. | Ensure the alarm icon (AL1/AL2) is visible on the display. Verify the alarm time is set correctly. |
| ബട്ടണുകൾ പ്രതികരിക്കുന്നില്ല. | Low batteries. Temporary software glitch. | Replace batteries. Remove and reinsert batteries to reset the device. |
സ്പെസിഫിക്കേഷനുകൾ
- ബ്രാൻഡ്: കിയൻസിൽ
- മോഡൽ: 14987
- നിറം: വെള്ളി/കറുപ്പ്
- അളവുകൾ: 6.6 x 3.81 x 2.2 സെ.മീ (2.6 x 1.5 x 0.9 ഇഞ്ച്)
- ഭാരം: 65 ഗ്രാം (2.3 ഔൺസ്)
- മെറ്റീരിയൽ: പ്ലാസ്റ്റിക്
- ഡിസ്പ്ലേ തരം: ഡിജിറ്റൽ
- ഊർജ്ജ സ്രോതസ്സ്: 2 x AAA/LR03 batteries (not included)
- പ്രത്യേക സവിശേഷതകൾ: DCF Radio-Controlled Time, 2 Alarms (Mon-Fri, Sat-Sun), Snooze Function, Indoor Temperature Display (°C/°F), Backlight, Touch Buttons, 12/24-hour format, Date and Day of Week display.
വാറൻ്റിയും പിന്തുണയും
For warranty information and customer support, please refer to the documentation provided at the time of purchase or contact your retailer. Kienzle products are designed for reliability and precision. Should you encounter any issues not covered in this manual, please reach out to the authorized service center or your point of purchase for assistance.