NYXI NJ10 വിസാർഡ് 2 TMR B ബ്ലൂടൂത്ത് കൺട്രോളർ ഇൻസ്ട്രക്ഷൻ മാനുവൽ

പ്രിയ ഗെയിമർ,
ഞങ്ങളുടെ ഉൽപ്പന്നം വാങ്ങിയതിന് നന്ദി.
നിങ്ങൾ ഉൽപ്പന്നം ഉപയോഗിക്കുന്നതിന് മുമ്പ്, ഉൽപ്പന്ന മാനുവൽ ശ്രദ്ധാപൂർവ്വം വായിക്കുക.

പാക്കേജ് ഉള്ളടക്കം

• NJ10 Left Controller ×1
• NJ10 Right Controller ×1
• NJ10 Middle Bridge x1
• Multi-function Receiver x1
• USB-C ചാർജിംഗ് കേബിൾ x1
• Receiver Extension Cable x1

സാങ്കേതിക പാരാമീറ്ററുകൾ

കണക്റ്റിവിറ്റി: Bluetooth 5.0, 2.4G Wireless
ബാറ്ററി ശേഷി: 400mAh (per controller)
ചാർജിംഗ്: USB-C വഴി 5V/0.4A
മെറ്റീരിയലുകൾ: PC + ABS + Metal + Silicone
ഭാരം: 225 ഗ്രാം
വലിപ്പം: 106*155*65.5എംഎം

സ്പെസിഫിക്കേഷൻ ഡയഗ്രം

CONNECTING TO NINTENDO SWITCH

1. Slide the controller downward along the rails on both sides of the console screen until it clicks. The “Controllers” interface on the console will display connected left/right controllers.
   
2. To remove the controller, press the release button on the back of the controller and slide it upward.
   
3. When the console is powered on, detaching the controller from the rails will automatically establish a Bluetooth connection with the Switch.
   
4. When the console is powered off, detach the controller from the rails and press the Home Button to power on and reconnect.
   
5. After successfully connecting to Switch, the controller vibrates for 1 second.
   

RECEIVER CONNECTION TO PC (XINPUT MODE)

1. Press and hold the Home Button for 3 seconds to power on. LEDs 1-4 on both controllers will flash green sequentially.
2. Insert the receiver into the PC and press and hold its button until the LED blinks rapidly,
3. ജോടിയാക്കുന്നതിനായി കാത്തിരിക്കുക.
   

RECEIVER CONNECTION TO PC (DINPUT MODE)

1. In Xinput mode, press and hold A + B + Home to switch to Dinput mode. LEDs 1-4 will blink green three times,
2. Repeat the same key combination to switch back to Xinput mode,
   

RECEIVER CONNECTION TO PC/NGC

Press and hold the home button of the right handle for 5 seconds to tum on the device, and the LED1-4 of the right handle will flash green.

Plug the receiver into the computer, and press and hold the button on the receiver until the LED flashes quickly.

Wait for the right handle and receiver to pair successfully, and the LED lights of the receiver and the handle will be on.

Press and hold the button on the receiver again until the LED flashes quickly, and press and hold the screen button on the left handle for 5 seconds until the LED1-4 of the left handle flashes green.

Wait for the left handle and receiver to pair successfully before it can be used normally.

RECEIVER CONNECTED TO WII

Turn on the Wii console, enter the game, and connect the original controller.

After entering the game, unplug the original adapter, and then plug the NJ10 receiver into the console, and press and hold the button on the receiver until the LED flashes quickly.

Press and hold the home button of the right handle for 5 seconds to turn on the device, and the LED1-4 of the right handle will flash green.

Wait for the right handle and receiver to pair successfully, and the LED lights of the receiver and the handle will be oоп.

Long press the button on the receiver again until the LED flashes quickly, and long press the screen button on the left handle for 5 seconds until the left handle LED1-4 flashes green water.

ജോയിസ്റ്റിക് കാലിബ്രേഷൻ

1. Press SL + SR+ + Button (left controller: Button) to enter calibration mode, Rotate the joysticks and press the same keys again to exit, A 1-second vibration confirms completion.
   
2. Switch System Calibration: Navigate to Settings > Controllers & Sensors > Calibrate Control Sticks and follow on-screen instructions.

ട്രിഗർ കാലിബ്രേഷൻ

Press SL + SR+ Home (left controller: Capture Button) to enter calibration mode. Press triggers fully to calibrate. Exit using the same keys (1-second vibration confirms completion).

6-AXIS GYROSCOPE CALIBRATION

1. സ്വിച്ച് ഓൺ: Navigate to Settings > Controllers & Sensors > Calibrate Motion Controls.
2. Place the controller on a flat surface and follow on-screen prompts, Press -and + Buttons to complete calibration.

ടർബോ ഫംഗ്ഷൻ

1. Supported Buttons: D-pad, A, B, X, Y, L, R, ZL, ZR,
2. ടർബോ പ്രാപ്തമാക്കുക: Hold the Setting Button, press a target button, then release. LED4 glows white.
3. വേഗത ക്രമീകരിക്കുക: Default is 12Hz (adjustable via app).
4. ടർബോ പ്രവർത്തനരഹിതമാക്കുക: Press the Setting Button + target button three times (LED4 turns off).

ബട്ടൺ പ്രോഗ്രാമിംഗ്

*Back Buttons (M * 1 / M * 2) : Can be mapped to other buttons or macros (max 21 actions per maсто),

1. മാപ്പിംഗ്: Hold Setting Button + target back button for 3 seconds, Press the desired button/macro sequence, then press the back button again to save.
   
2. മാപ്പിംഗ് മായ്‌ക്കുക: Hold Setting Button + back button for 3 seconds, then press the back button without input.
   

പ്രമാണങ്ങൾ / വിഭവങ്ങൾ

NYXI NJ10 Wizard 2 TMR B Bluetooth Controller [pdf] നിർദ്ദേശ മാനുവൽ NJ10, NJ10 Wizard 2 TMR B Bluetooth Controller, Wizard 2 TMR B Bluetooth Controller, Bluetooth Controller, Controller

റഫറൻസുകൾ

• ഉപയോക്തൃ മാനുവൽ