MACHINIST H81M-PRO S1 Motherboard User Manual

1. സജ്ജീകരണ നിർദ്ദേശങ്ങൾ

1.1 പാക്കേജ് ഉള്ളടക്കം

The package for your MACHINIST H81M-PRO S1 motherboard should include the following items:

• MACHINIST H81M-PRO S1 Motherboard (1 piece)
• I/O Shield (1 piece)
• SATA Cable (1 piece)

Note: Accessories are subject to change without prior notice. Please check the package contents upon receipt.

1.2 ഓവർview ഘടകങ്ങളുടെ

Familiarize yourself with the layout of your motherboard. The diagram below highlights key components and connectors.

1.3 Install CPU & Fan

Please install the CPU into the CPU socket as shown in the following steps:

1. Gently lift the CPU socket lever.
2. Align the CPU with the socket, ensuring the triangular mark on the CPU matches the mark on the socket.
3. നിർബന്ധിച്ച് അമർത്താതെ സിപിയു ശ്രദ്ധാപൂർവ്വം സോക്കറ്റിൽ വയ്ക്കുക.
4. Lower the lever back into place to secure the CPU.
5. Apply an even layer of thermal paste to the CPU.
6. Install the CPU cooler, ensuring it is securely attached and the heatsink forms a tight seal with the CPU.
7. Connect the CPU cooler's 4-pin fan power connector to the CPU_FAN1 header on the motherboard.

പ്രധാനപ്പെട്ട സുരക്ഷാ കുറിപ്പുകൾ:

• ഹാർഡ്‌വെയർ കേടുപാടുകൾ തടയുന്നതിന് സിപിയു ഇൻസ്റ്റാൾ ചെയ്യുന്നതിനോ നീക്കം ചെയ്യുന്നതിനോ മുമ്പായി പവർ ഔട്ട്‌ലെറ്റിൽ നിന്ന് പവർ കോർഡ് എപ്പോഴും അൺപ്ലഗ് ചെയ്യുക.
• Retain the CPU protective cap after installing the processor.
• Do not turn on the computer if the CPU cooler is not installed; overheating and damage may occur.
• Whenever the CPU is not installed, protect the CPU socket pins with a plastic cap.

1.4 Install Memory

The motherboard provides two DDR3 DIMM slots with a maximum capacity of 16GB (8GB x 2). Follow these steps to install memory modules:

1. മെമ്മറി സ്ലോട്ടിന്റെ ഇരുവശത്തുമുള്ള ലാച്ചുകൾ പുറത്തേക്ക് വലിക്കുക.
2. Insert the memory module into the slot, aligning the notch on the module with the key in the slot.
3. Flip the latches on both sides of the slot inwards to lock the memory module in place.

പ്രധാന കുറിപ്പുകൾ:

• Always turn off the computer and unplug the power cord before installing memory.
• Memory modules have a foolproof design; they can only be inserted in one direction. Do not force them.
• This motherboard supports Dual Channel Technology. Dual-Channel mode requires two memory modules.

1.5 Install Expansion Card

The motherboard provides one PCI Express 2.0 x16 slot and one PCI Express 2.0 x1 slot. To install an expansion card:

1. Select an available PCI Express slot (PCIEXP1: PCIe 2.0 x16 or PCIE2: PCIe 2.0 x1).
2. Align the expansion card with the chosen slot.
3. Press the expansion card firmly until it is fully inserted and secured in the slot.

പ്രധാനപ്പെട്ട സുരക്ഷാ കുറിപ്പുകൾ:

• Always turn off the power supply and unplug the power cable before adding or removing expansion cards.
• Incorrect installation can cause short circuits and damage to the card or motherboard.

1.6 ബാക്ക് പാനൽ കണക്ടറുകൾ

The back panel provides various ports for connecting external devices:

• PS/2 Ports (x2): One green for mouse, one purple for keyboard.
• HDMI Port (x1): Supports 4K and 1080p for connecting HDMI-supported monitors.
• VGA Port (x1): Supports analog video signal transmission for high-resolution displays.
• USB 3.0 പോർട്ടുകൾ (x2): Compatible with USB 3.0 and USB 2.0 devices.
• USB 2.0 പോർട്ടുകൾ (x2): For connecting USB 2.0 devices.
• RJ45 LAN Port (x1): Gigabit Ethernet port for Internet connection (up to 1000Mbps/s).
• Audio Ports (x3): Line-in (blue), Line-out (green), Mic-in (pink).

1.7 ആന്തരിക കണക്ടറുകൾ

The motherboard features several internal connectors for various components:

F_PANEL1 Connector (Front Panel Header)

This header connects to the front panel buttons and indicators of your PC case. Ensure correct polarity for proper function.

SPEAK1 Connector (Speaker Header)

Connects to the internal speaker for system beeps and alerts.

JAUDIO1 Connector (Front Panel Audio Header)

This connector allows you to connect audio jacks on the front panel of your case.

Important: An incorrect connection can prevent the device from working or even damage it.

SATA1~2: SATA 3.0 കണക്ടറുകൾ; SATA3~4: SATA 2.0 കണക്ടറുകൾ

These connectors are for connecting SATA storage devices (HDDs, SSDs). SATA 3.0 ports offer 6Gb/s transfer speeds, while SATA 2.0 ports offer 3Gb/s.

M.2 സ്ലോട്ട്

The motherboard includes an M.2 slot for NVMe M.2 SSDs. To install an M.2 SSD:

1. 2 ഡിഗ്രി കോണിൽ M.2 സ്ലോട്ടിലേക്ക് നിങ്ങളുടെ M.30 SSD ചേർക്കുക.
2. Gently push down the SSD.
3. Secure the M.2 SSD in place with the provided screw.

JCOM1: സീരിയൽ പോർട്ട് കണക്ടർ

This connector can provide one serial port via an optional COM port cable.

ATXPWR1, JATXPWR1: പവർ കണക്ടറുകൾ

These are the main power connectors for the motherboard. ATXPWR1 is the 24-pin main power connector, and JATXPWR1 is the 8-pin CPU power connector. Ensure your power supply is sufficient (at least 500W recommended) and properly connected before powering on.

CPU_FAN1, SYS_FAN1~3: ഫാൻ കണക്ടറുകൾ

• CPU_FAN1 (4-pin): For the CPU cooler fan. Supports PWM intelligent speed regulation based on load and temperature.
• SYS_FAN1~3 (3-pin): For case fans. Does not support PWM adjustment.

JUSB2, JUSB4: USB 2.0 കണക്ടറുകൾ

These headers conform to the USB 2.0 specification and allow you to connect USB 2.0 ports on the front panel of your case.

FUSB3: USB 3.0 കണക്റ്റർ

This header conforms to the USB 3.0 specification and allows you to connect USB 3.0 ports on the front panel of your case.

2. പ്രവർത്തന നിർദ്ദേശങ്ങൾ

2.1 ബയോസ് സജ്ജീകരണം

The BIOS (Basic Input and Output System) manages hardware parameters and initiates the system boot process. It identifies, configures, tests, and connects computer hardware to the OS.

ബയോസ് സജ്ജീകരണത്തിലേക്ക് പ്രവേശിക്കുന്നു

To enter the BIOS Setup Menu, repeatedly press the DEL key immediately after starting the computer. If the message disappears before you press DEL, restart your computer and try again.

Important: Functions and screens may vary slightly depending on the specific BIOS version.

3. പരിപാലനം

3.1 Reset BIOS

If you encounter issues or need to restore default settings, you can reset the BIOS using one of the following methods:

• Through BIOS Menu: Enter BIOS Setup and press F6 ഒപ്റ്റിമൈസ് ചെയ്ത സ്ഥിരസ്ഥിതികൾ ലോഡുചെയ്യുന്നതിന്.
• Clear CMOS Jumper: Short the Clear CMOS jumper (JCMOS1) on the motherboard.

Important: Always ensure the computer is powered off and unplugged before clearing CMOS data using the jumper.

3.2 CMOS Discharge (Clear CMOS)

To discharge the CMOS and reset BIOS settings:

1. Locate the JCMOS1 jumper on the motherboard. In its initial state, pins 1 and 2 are covered.
2. To discharge, move the jumper cap to cover pins 2 and 3.
3. Wait for approximately 3 minutes for the discharge to complete.
4. Restore the jumper cap to its initial position (covering pins 1 and 2).

Important: Always turn off the computer and unplug the power cord from the power outlet before discharging the CMOS.

4. പ്രശ്‌നപരിഹാരം

• System won't boot: Ensure all power connectors (24-pin and 8-pin) are securely attached. Verify CPU and RAM are correctly installed. Check if the power supply is sufficient (at least 500W recommended).
• NVMe M.2 SSD not recognized: Ensure the M.2 SSD is properly seated in the slot. Check BIOS settings to confirm M.2 support is enabled and configured correctly. Some M.2 slots may share bandwidth with SATA ports; ensure no conflicts.
• BIOS update issues: BIOS flashing is potentially risky. Only update if necessary to resolve specific problems. Inadequate flashing can lead to system malfunction. Refer to the BIOS section for reset procedures if issues arise after an update attempt.
• Incorrect component installation: Always ensure components like CPU, RAM, and expansion cards are installed correctly and without force. Incorrect installation can cause hardware damage.

5 സ്പെസിഫിക്കേഷനുകൾ

6 ഉപയോക്തൃ നുറുങ്ങുകൾ

• വൈദ്യുതി വിതരണം: This motherboard requires a stable and sufficient power supply. A 500W (or higher) branded power supply is strongly recommended for optimal performance and stability.
• മെമ്മറി അനുയോജ്യത: For best compatibility and stability, use DDR3 desktop memory from international brands such as Samsung, Kingston, Sandee, Micron, or Hynix. Other brands may not be fully compatible.
• NVMe M.2 Support: The motherboard supports NVMe M.2 SSDs. If you encounter issues with recognition, ensure the drive is properly seated and check BIOS settings.
• ബയോസ് അപ്‌ഡേറ്റുകൾ: Only update the BIOS if absolutely necessary to address specific issues. Incorrect BIOS flashing can lead to system instability.
• സിപിയു അനുയോജ്യത: This motherboard is designed for Intel LGA 1150 processors (4th generation Core i3/i5/i7, Xeon E3/V3, Celeron G, Pentium G series). It is not compatible with newer generations like 7th or 9th gen Intel CPUs (e.g., i7 6700k, i3 9100f) or Xeon E5 series processors (e.g., E5 2620 V3/V4).

7. വാറൻ്റിയും പിന്തുണയും

For technical support, warranty claims, or any questions not covered in this manual, please contact the seller or MACHINIST official support channels.

A detailed user manual in PDF format is available for download. You can access it via the following link: MACHINIST H81M-PRO S1 User Manual (PDF).