1. ആമുഖം
This manual provides essential information for the safe and effective use of your Japan Nidec 24H Brushless Servo Motor. This motor features a built-in drive and 100-line dual-channel encoder, making it suitable for high-precision control applications. Please read this manual thoroughly before operation.
2. Safety & Warnings
- Do not operate the motor under overload (stall) conditions, as this may easily damage the motor.
- Select a power supply with appropriate voltagഇ (ഡിസി).
- If the load exceeds the rated value, the rotational speed will decrease.
- Operating near the stall torque limit may cause internal damage.
- Reducing the rotational speed will result in decreased output torque.
- It is strictly forbidden to make mistakes regarding the positive and negative connections of the brushless motor.
- Always use a regulated, non-surge DC power supply (e.g., a battery or regulated power supply).
ശ്വാസംമുട്ടൽ അപകട മുന്നറിയിപ്പ്
This product may contain small parts. Keep out of reach of children under 3 years to prevent choking hazards.
3. ഉൽപ്പന്നം കഴിഞ്ഞുview
The Nidec 24H Brushless Servo Motor is a compact and powerful motor designed for precision applications. It features an integrated brushless driver and a 100-line encoder for accurate feedback and control.
4 സ്പെസിഫിക്കേഷനുകൾ
പൊതു ഗുണങ്ങൾ
- തരം: മൈക്രോ മോട്ടോർ
- Commutation: ബ്രഷ് ഇല്ലാത്തത്
- ഉത്ഭവം: മെയിൻലാൻഡ് ചൈന
- സർട്ടിഫിക്കേഷൻ: CCC
- വ്യവസ്ഥ: Used (dismantled, tested and in perfect working order)
ഇലക്ട്രിക്കൽ ഡാറ്റ
| വാല്യംtage | നോ-ലോഡ് കറന്റ് | നോ-ലോഡ് സ്പീഡ് |
|---|---|---|
| DC 9V | 70mA | 2246 ആർപിഎം |
| DC 12V | 80mA | 3020 ആർപിഎം |
| DC 24V | 100mA | 6100 ആർപിഎം |
അളവുകൾ
പാക്കേജ് വിവരങ്ങൾ
- ഭാരം: 0.15 കി.ഗ്രാം
- അളവുകൾ (L x W x H): 9 സെ.മീ x 9 സെ.മീ x 9 സെ.മീ
5. സജ്ജീകരണം
വയറിംഗ് നിർദ്ദേശങ്ങൾ
Refer to the wiring diagram below for proper connections. Ensure all connections are secure before applying power.
- റെഡ് വയർ: പവർ സപ്ലൈ പോസിറ്റീവ്
- ബ്ലാക്ക് വയർ: വൈദ്യുതി വിതരണം നെഗറ്റീവ്
- മഞ്ഞ വയർ: Start/Stop (Connect to positive power supply via a 1k resistor; below 12V, no resistor needed)
- White Wire (PWM): PWM signal speed control (Connect to negative for high speed; input 20KHz pulse width signal for speed regulation)
- ഗ്രീൻ വയർ: Forward-reverse switching (Connect to negative to switch direction)
- Brown Wires (Signal A, Signal B): എൻകോഡർ സിഗ്നലുകൾ
- ഓറഞ്ച് വയർ: Encoder power supply 5V
മൗണ്ടിംഗ്
The motor bracket can be removed if necessary for custom mounting solutions.
6. പ്രവർത്തന നിർദ്ദേശങ്ങൾ
അടിസ്ഥാന പ്രവർത്തനം
- Connect the red wire to the positive pole and the black wire to the negative pole of your DC power supply.
- Connect the yellow 'Start' line to the positive power supply via a 1k resistor. If operating below 12V, a resistor is not required.
- To run at high speed, connect the white PWM line directly to the negative pole.
- For speed regulation, input a 20KHz pulse width modulation (PWM) signal to the white line.
- To switch between forward and reverse rotation, connect the green line to the negative pole. It is recommended to stop the motor before switching direction to prevent instantaneous surges.
- The encoder requires a 5V power supply connected to the orange wire. If the encoder is not needed, this connection can be ignored.
7. പരിപാലനം
This brushless servo motor is designed for low maintenance. Keep the motor clean and free from dust and debris. Ensure proper ventilation to prevent overheating. No specific user-serviceable parts are inside.
8. പ്രശ്നപരിഹാരം
- Motor not starting or erratic operation: Check all wiring connections for correctness, especially positive/negative polarity. Ensure the power supply is regulated and within the specified voltage ശ്രേണി (9V-24V DC).
- മോട്ടോർ അമിത ചൂടാക്കൽ: Reduce the load on the motor. Ensure it is not operating under stall conditions. Verify that the power supply voltage is correct and not exceeding 24V.
- Reduced speed or torque: The load might be exceeding the motor's rated value. Reduce the load or ensure the motor is not operating near its stall torque limit.
- No encoder feedback: Ensure the encoder's 5V power supply (orange wire) is correctly connected.
9 ഉപയോക്തൃ നുറുങ്ങുകൾ
- കേബിളുകൾ: This motor is typically sold without connecting cables. You will need to source appropriate wires and connectors for your application.
- Shaft Dimensions: For precise integration, carefully measure the helical portion of the shaft if specific dimensions are critical for your project. The shaft diameter is 6mm and length is 18.5mm.
- വ്യവസ്ഥ: As these motors are often used and dismantled, minor cosmetic imperfections like oxidation or rust spots may be present, but they are tested for perfect working order.
10. വാറണ്ടിയും പിന്തുണയും
For detailed information regarding the manufacturer and EU representative, please refer to the original user manual PDF.
നിർമ്മാതാവ്: Dongguan Haodarong Trading Co., Ltd
വിലാസം: Room406, No.11, Jiaoyu Road, Dongcheng Street, Dongguan, China
ബന്ധപ്പെടേണ്ട വ്യക്തി: Liao Jiansheng
ഇ-മെയിൽ: mox0903@163.com
EU ഉത്തരവാദിത്തമുള്ള വ്യക്തി: QTEC EUREP GMBH
വിലാസം: CURTIUSSTRASSE 27, 23568 LUEBECK, Germany
ഇ-മെയിൽ: Cpcs@cpcs-tlab.hk
ഫോൺ: +852-53700017
PDF ഫോർമാറ്റിലുള്ള ഒരു സമഗ്രമായ ഉപയോക്തൃ മാനുവൽ ഡൗൺലോഡ് ചെയ്യാൻ ലഭ്യമാണ്: View ഉപയോക്തൃ മാനുവൽ (PDF)
