GEOID CS600 Smart Cycling Speed and Cadence Sensor

1. ആമുഖം

The GEOID CS600 is a versatile 2-in-1 Smart Cycling Speed and Cadence Sensor designed to accurately track your cycling performance. It features dual-mode transmission supporting both Bluetooth 5.0 and ANT+ protocols, ensuring compatibility with a wide range of bike computers, smartwatches, and cycling applications. With its IP66 waterproof rating and long battery life, the CS600 is built for reliable performance in various conditions.

2. പാക്കേജ് ഉള്ളടക്കം

എല്ലാ ഇനങ്ങളും ഉണ്ടെന്ന് ഉറപ്പാക്കാൻ പാക്കേജ് പരിശോധിക്കുക:

• 1 x GEOID CS600 Sensor
• 1 x Flat Rubber Pad
• 1 x CR2032 Battery (Pre-installed in Sensor)
• 1 x Small Rubber Elastic Ring (For Crank Arm)
• 1 x Large Rubber Elastic Ring (For Hub)

3 സ്പെസിഫിക്കേഷനുകൾ

4. സജ്ജീകരണം

4.1. Battery Installation and Insulation Removal

The CR2032 battery is pre-installed in the sensor. Before first use, you must remove the battery insulation sheet to activate the sensor.

1. Gently open the battery cover on the back of the sensor.
2. Remove the small plastic insulation sheet located between the battery and the contact.
3. Ensure the CR2032 battery is correctly seated with the positive (+) side facing up.
4. ബാറ്ററി കവർ സുരക്ഷിതമായി അടയ്ക്കുക.

4.2. മോഡ് തിരഞ്ഞെടുക്കൽ

The CS600 sensor can operate in either Cadence Mode or Speed Mode. The mode is selected by reinstalling the battery:

• Cadence Mode: എങ്കിൽ ചുവപ്പ് indicator flashes, the sensor is in Cadence Mode.
• സ്പീഡ് മോഡ്: എങ്കിൽ പച്ച indicator flashes, the sensor is in Speed Mode.

To switch modes, remove the battery, wait a few seconds, and then reinstall it. The sensor will alternate between red and green flashes upon reinstallation. Select your desired mode by observing the indicator light.

4.3. സെൻസർ ഇൻസ്റ്റലേഷൻ

Install the sensor according to the selected mode:

• For Cadence Mode (RED indicator): Install the sensor on the left inner crank arm of your bicycle.
• For Speed Mode (GREEN indicator): Install the sensor on the front hub of your bicycle.

5. പ്രവർത്തന നിർദ്ദേശങ്ങൾ

5.1. Connecting to Devices and Apps

The GEOID CS600 supports both ANT+ and Bluetooth Dual Protocol, allowing connection to a wide range of devices and applications:

• ANT+ അനുയോജ്യത: Connects with ANT+ bike computers, watches, and cycling software such as Garmin (e.g., 530/830/1030plus), Bryton (e.g., 310/405/420/750), iIGPSPORT (e.g., 50/320/520/620), Magene (e.g., C206/406), and Wahoo. Generally, if your device supports ANT+, it should be compatible.
• ബ്ലൂടൂത്ത് 4.0 അനുയോജ്യത: Connects with popular cycling apps like ZWIFT, Wahoo Fitness, and TrainerRoad.

To connect, ensure your device or app's Bluetooth or ANT+ is enabled and search for new sensors. The CS600 will appear as an available device.

5.2. ഡാറ്റ രേഖപ്പെടുത്തൽ

Once connected, the sensor will transmit speed or cadence data to your paired device or application. You can connect ANT+ devices and Bluetooth apps simultaneously to record data from two sources, ensuring stable transmission.

6. പരിപാലനം

6.1. Waterproof and Dustproof

The CS600 sensor has an IP66 waterproof and dustproof rating, meaning it is protected against powerful water jets and dust ingress. This makes it suitable for use in various weather conditions.

• പ്രധാനപ്പെട്ടത്: Do not soak the sensor in water.
• പ്രധാനപ്പെട്ടത്: Avoid cleaning the sensor with high-pressure water jets.

6.2. ബാറ്ററി മാറ്റിസ്ഥാപിക്കൽ

The sensor uses a standard CR2032 3V lithium battery, which provides approximately 500 hours of usage. When the battery is low, the indicator light may behave erratically or the sensor may fail to connect. To replace the battery:

1. Gently open the battery cover on the back of the sensor.
2. പഴയ CR2032 ബാറ്ററി നീക്കം ചെയ്യുക.
3. പോസിറ്റീവ് (+) വശം മുകളിലേക്ക് അഭിമുഖീകരിക്കുന്ന ഒരു പുതിയ CR2032 ബാറ്ററി ഇടുക.
4. ബാറ്ററി കവർ സുരക്ഷിതമായി അടയ്ക്കുക.
5. The sensor will flash red or green to indicate mode selection upon battery reinstallation.

7. പ്രശ്‌നപരിഹാരം

• ഉപകരണം/ആപ്പ് സെൻസർ കണ്ടെത്തിയില്ല:
  • Ensure the battery insulation sheet has been removed.
  • Check if the battery is installed correctly and has sufficient charge.
  • Verify that your device's Bluetooth or ANT+ is enabled.
  • Make sure the sensor is in the correct mode (red for cadence, green for speed) for your intended use.
  • Try reinstalling the battery to reset the sensor and re-select the mode.
  • After switching modes, please reconnect the device to display the different modes correctly.
• കൃത്യമല്ലാത്ത വായനകൾ:
  • Ensure the sensor is securely mounted in the correct position (crank arm for cadence, front hub for speed).
  • സെൻസറിന് സമീപം എന്തെങ്കിലും തടസ്സങ്ങളോ ഇടപെടലുകളോ ഉണ്ടോയെന്ന് പരിശോധിക്കുക.
• Sensor not suitable for spinning bikes:
  • Note that this sensor is a geomagnetic sensor and is specifically designed for outdoor cycling. It is not suitable for use with spinning bikes.

8 ഉപയോക്തൃ നുറുങ്ങുകൾ

• Simultaneous Speed and Cadence Tracking: If you wish to record both speed and cadence data simultaneously, you will need two separate CS600 sensors. One sensor can be set to Cadence Mode and installed on the crank arm, while the other is set to Speed Mode and installed on the front hub.
• അനുയോജ്യത പരിശോധന: While the sensor supports common ANT+ and Bluetooth protocols, always verify compatibility with your specific bike computer or cycling app before extended use.

9. വാറൻ്റിയും പിന്തുണയും

For any product-related inquiries, technical support, or warranty claims, please contact GEOID customer service through the official store or platform where the product was purchased. Please retain your proof of purchase for warranty purposes.