BENINCA TO.GO 4WV Garage Door Opener Remote Control User Manual

1. ആമുഖം

This manual provides instructions for the BENINCA TO.GO 4WV garage door opener remote control. This device is designed to operate BENINCA garage doors and gate openers using a 433.92MHz rolling code frequency. Please read this manual carefully before use to ensure proper operation and longevity of your remote control.

2. ഉൽപ്പന്നം കഴിഞ്ഞുview

The BENINCA TO.GO 4WV is a compact and reliable hand transmitter featuring four buttons for controlling multiple functions or devices. It utilizes rolling code technology for enhanced security.

2.1 പാക്കേജ് ഉള്ളടക്കം

• 1 x BENINCA TO.GO 4WV Remote Control
• 1 x ബാറ്ററി (മുൻകൂട്ടി ഇൻസ്റ്റാൾ ചെയ്തത്)
• 1 x കീചെയിൻ

2.2 ഉൽപ്പന്ന ദൃശ്യങ്ങൾ

ചിത്രം 1: മുൻഭാഗം view of the remote control with four white buttons.

ചിത്രം 2: വിശദമായ മുൻഭാഗം view showing the LED indicator and buttons.

ചിത്രം 3: സൈഡ് പ്രോfile വിദൂര നിയന്ത്രണത്തിന്റെ.

ചിത്രം 4: കോണാകൃതിയിലുള്ളത് view highlighting the ergonomic design.

ചിത്രം 5: പിൻഭാഗം view with the battery compartment cover.

Figure 6: Dimensions of the remote control (approximately 70mm x 40mm x 14mm).

2.3 ഉൽപ്പന്ന വീഡിയോ

3 സ്പെസിഫിക്കേഷനുകൾ

4. സജ്ജീകരണവും പ്രോഗ്രാമിംഗും

To program your BENINCA TO.GO 4WV remote control, you will need access to your existing BENINCA receiver or opener unit. The programming procedure typically involves interacting directly with the receiver unit, not just the remote itself.

General Programming Steps (may vary by receiver model):

1. Locate the Receiver: Find the control unit for your garage door or gate opener. This is usually located near the motor or inside a control box.
2. Access Programming Button: On the receiver, locate the programming button (often labeled 'PROG', 'MEMO', 'LEARN', or similar). Consult your original BENINCA receiver/opener manual for its exact location and labeling.
3. പഠന രീതി സജീവമാക്കുക: Press and release the programming button on the receiver. An LED indicator on the receiver should light up or flash, indicating it is in learning mode.
4. Transmit Code from New Remote: Within a few seconds (usually 5-10 seconds), press and hold the desired button on your new BENINCA TO.GO 4WV remote control that you wish to program.
5. പ്രോഗ്രാമിംഗ് സ്ഥിരീകരിക്കുക: The LED on the receiver should change its state (e.g., flash rapidly, turn off, or light up solid) to confirm successful programming. Release the button on the remote.
6. റിമോട്ട് പരീക്ഷിക്കുക: Wait a few seconds for the receiver to exit learning mode, then test the newly programmed button on your remote control to ensure it operates the garage door or gate.

Important: Always refer to the specific instruction manual for your BENINCA receiver/opener model for precise programming steps, as procedures can vary. Ensure you have access to your receiver before attempting to program the remote.

5. ഓപ്പറേഷൻ

Once programmed, operating your BENINCA TO.GO 4WV remote control is straightforward:

1. നിങ്ങളുടെ ഗാരേജ് വാതിലിലേക്കോ ഗേറ്റ് ഓപ്പണറിലേക്കോ റിമോട്ട് കൺട്രോൾ ചൂണ്ടുക.
2. Press the programmed button corresponding to the function you wish to activate (e.g., open, close, stop).
3. The LED indicator on the remote control will light up briefly when a button is pressed, confirming signal transmission.

Figure 7: Demonstrating button press on the remote control.

6. പരിപാലനം

6.1 ബാറ്ററി മാറ്റിസ്ഥാപിക്കൽ

The remote control comes with a pre-installed battery. If the remote's range decreases significantly or the LED indicator does not light up when a button is pressed, it's likely time to replace the battery.

ബാറ്ററി മാറ്റിസ്ഥാപിക്കാൻ:

1. Locate the battery compartment cover on the back of the remote control (refer to Figure 5).
2. Carefully open the compartment using a small screwdriver or by sliding the cover as indicated.
3. Remove the old battery. Note its orientation (+/-).
4. അതേ തരത്തിലുള്ള ഒരു പുതിയ ബാറ്ററി ഇടുക, ശരിയായ പോളാരിറ്റി ഉറപ്പാക്കുക.
5. ബാറ്ററി കമ്പാർട്ട്മെൻ്റ് കവർ സുരക്ഷിതമായി അടയ്ക്കുക.

Warning: Dispose of old batteries responsibly according to local regulations. Keep batteries out of reach of children.

6.2 വൃത്തിയാക്കൽ

Wipe the remote control with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these can damage the casing അല്ലെങ്കിൽ ആന്തരിക ഘടകങ്ങൾ.

7. പ്രശ്‌നപരിഹാരം

If your remote control is not functioning as expected, try the following troubleshooting steps:

• പ്രോഗ്രാമിംഗിന് ശേഷം റിമോട്ട് പ്രവർത്തിക്കുന്നില്ല: Double-check the programming steps in your receiver's manual. Ensure the receiver was in learning mode and the correct button was pressed on the remote.
• ഹ്രസ്വ പ്രവർത്തന ശ്രേണി: Replace the battery in the remote control. Ensure there are no obstructions between the remote and the receiver. Check for sources of radio interference (e.g., other wireless devices, metal structures).
• LED on remote does not light up: The battery may be dead or incorrectly installed. Replace the battery.
• റിമോട്ട് ഇടയ്ക്കിടെ പ്രവർത്തിക്കുന്നു: This could indicate a low battery, interference, or a loose connection inside the remote. Try replacing the battery first.

If the issue persists after trying these steps, contact customer support or a qualified technician.

8 ഉപയോക്തൃ നുറുങ്ങുകൾ

• Keep Receiver Manual Handy: For programming and advanced settings, always refer to the instruction manual of your BENINCA garage door or gate receiver/opener. This is crucial for successful setup.
• ടെസ്റ്റ് റേഞ്ച്: After programming, test the remote's operating range from various distances and angles to ensure reliable performance.
• നിങ്ങളുടെ റിമോട്ട് സുരക്ഷിതമാക്കുക: Treat your remote control like a key. Keep it in a secure location to prevent unauthorized access to your garage or gate.

9. വാറൻ്റിയും പിന്തുണയും

For warranty information, technical support, or service inquiries, please refer to the documentation provided with your purchase or contact the seller directly. Keep your proof of purchase for warranty claims.