1. ആമുഖം
This manual provides instructions for the BENINCA TO.GO 2WV series garage door remote control. This remote is designed to operate with BENINCA rolling code systems at a frequency of 433.92MHz. It is available in 2-button and 4-button configurations.
Please read this manual carefully before attempting to set up or use your new remote control.
2. പാക്കേജ് ഉള്ളടക്കം
പാക്കേജ് തുറക്കുമ്പോൾ, നിങ്ങൾ ഇനിപ്പറയുന്ന ഇനങ്ങൾ കണ്ടെത്തണം:
- 1 x Remote Control (2-button or 4-button version)
- 1 x Battery (pre-installed or included separately)
- 1 x കീചെയിൻ
- 1 x ഇംഗ്ലീഷ് മാനുവൽ
Video: Unboxing and basic operation of the remote control.
3 സ്പെസിഫിക്കേഷനുകൾ
| ഫീച്ചർ | വിശദാംശങ്ങൾ |
|---|---|
| മോഡൽ | TO.GO 2WV (and compatible series) |
| ആവൃത്തി | 433.92MHz |
| എൻകോഡിംഗ് രീതി | Rolling Code (64-bit) |
| ബട്ടണുകൾ | 2 അല്ലെങ്കിൽ 4 |
| ബാറ്ററി | ഉൾപ്പെടുത്തിയിട്ടുണ്ട് |
| Dimensions (2-button) | Approx. 70mm (L) x 40mm (W) x 14mm (T) |
| സർട്ടിഫിക്കേഷൻ | CE |
| ഉത്ഭവം | മെയിൻലാൻഡ് ചൈന |
ചിത്രം: Views of the 2-button remote control (front, side, and back with battery cover).
Image: Dimensions of the 2-button remote control.
4 അനുയോജ്യത
This remote control is compatible with the following BENINCA rolling code models (64-bit):
- Beninca TO GO 2WV
- Beninca TO GO 4WV
- BENINCA IO.2WV
- BENINCA LO.T2WMR
- BENINCA T2 WV
- BENINCA T4 WV
- BENINCA CUPIDO-2
- BENINCA CUPIDO-4
- APPLE 4WV / APPLE 2WV
It is compatible with all color variations of these models.
Image: Visual guide to compatible BENINCA rolling code remote models.
5. പ്രധാന കുറിപ്പുകൾ
- This remote control is അല്ല applicable to the new yellow button BENINCA TO 2VA 4VA models, which use ARC code.
- This remote can be programmed directly at the receiver unit of your garage door opener.
- അത് അല്ല possible to clone an existing remote control to this device. Programming must be done at the receiver.
Image: Visual warning distinguishing between incompatible ARC code (TO.GO 2A) and compatible rolling code (TO.GO 2WV) remotes.
6. സജ്ജീകരണവും പ്രോഗ്രാമിംഗും
Programming this remote control requires access to your BENINCA garage door opener's receiver unit. The exact steps may vary slightly depending on your specific receiver model. Always refer to your garage door opener's manual for precise programming instructions.
General programming steps for BENINCA rolling code receivers:
- Locate the Receiver: The receiver unit is typically located on the garage door opener motor itself, or sometimes in a separate control box near the motor.
- Find the Programming Button: Look for a small button on the receiver, often labeled 'PROG', 'MEMO', 'LEARN', or similar. It might be recessed and require a small pointed object (like a paperclip) to press.
- പഠന രീതി സജീവമാക്കുക: Press and release the programming button on the receiver. An LED indicator on the receiver should light up or flash, indicating it is in learning mode. This mode usually lasts for a few seconds.
- Transmit from New Remote: While the receiver is in learning mode, press and hold the desired button on your new BENINCA remote control for 1-2 seconds.
- പ്രോഗ്രാമിംഗ് സ്ഥിരീകരിക്കുക: The LED on the receiver should flash or change state to confirm successful programming. Release the button on the remote.
- റിമോട്ട് പരീക്ഷിക്കുക: Wait a few seconds for the receiver to exit learning mode, then press the programmed button on your new remote to test its operation.
Important: If you have multiple remotes to program, repeat steps 3-5 for each remote and desired button within the receiver's learning window.
7. പ്രവർത്തന നിർദ്ദേശങ്ങൾ
Once programmed, operating your BENINCA remote control is straightforward:
- തുറക്കൽ/അടയ്ക്കൽ: Press the programmed button on the remote control. The garage door will open or close.
- Stopping Movement: Press the programmed button again while the door is in motion to stop it.
- LED സൂചകം: When a button is pressed, the LED indicator on the remote will light up, confirming that a signal is being transmitted.
Image: Demonstrating pressing a button on the 4-button remote.
Image: Demonstrating pressing a button on the 2-button remote.
8. പരിപാലനം
ബാറ്ററി മാറ്റിസ്ഥാപിക്കൽ
If the remote control's LED indicator does not light up or appears dim when a button is pressed, the battery may need to be replaced. The remote uses a standard coin cell battery (e.g., CR2032, specific type may vary, check your remote's battery compartment).
- റിമോട്ട് തുറക്കുക: Locate the small notch or opening at the bottom of the remote. Use a small flat-head screwdriver or a coin to carefully pry open the remote casing.
- പഴയ ബാറ്ററി നീക്കം ചെയ്യുക: Carefully remove the old battery from its compartment. Note the orientation (+/-).
- പുതിയ ബാറ്ററി ഇടുക: ശരിയായ പോളാരിറ്റി ഉള്ള ഒരു പുതിയ ബാറ്ററി ചേർക്കുക.
- റിമോട്ട് അടയ്ക്കുക: റിമോട്ട് സി. എടുക്കുക.asing സുരക്ഷിതമായി തിരികെ ഒരുമിച്ച് ചേർക്കുക.
- ടെസ്റ്റ്: Test the remote's function with your garage door opener.
Refer to the unboxing video in Section 2 for a visual guide on accessing the battery compartment.
9. പ്രശ്നപരിഹാരം
| പ്രശ്നം | സാധ്യമായ കാരണം | പരിഹാരം |
|---|---|---|
| പ്രോഗ്രാമിംഗ് കഴിഞ്ഞാൽ റിമോട്ട് പ്രവർത്തിക്കുന്നില്ല. | Incorrect programming steps, receiver not in learning mode, or remote not compatible. | Review Section 5 (Important Notes) and Section 6 (Setup and Programming). Ensure your remote is compatible and re-attempt programming carefully. Consult your opener's manual. |
| Remote LED does not light up when button is pressed. | നിർജ്ജീവമായ അല്ലെങ്കിൽ കുറഞ്ഞ ബാറ്ററി. | Replace the battery as described in Section 8. |
| Remote works intermittently or has reduced range. | Low battery, interference, or remote/receiver obstruction. | Replace battery. Check for sources of interference (e.g., other wireless devices). Ensure clear line of sight between remote and receiver. |
| Cannot clone an existing remote. | This remote uses rolling code and cannot be cloned. | This is expected behavior. Programming must be done directly at the receiver as per Section 6. |
10 ഉപയോക്തൃ നുറുങ്ങുകൾ
- Always keep your garage door opener's manual handy for specific programming details, as procedures can vary by model.
- If you have multiple BENINCA rolling code openers, you can often program different buttons on a single remote to control different doors.
- Store your remote in a safe place, away from extreme temperatures or direct sunlight, to prolong battery life and device integrity.
11. വാറൻ്റിയും പിന്തുണയും
For any issues or questions regarding your BENINCA remote control, please contact the seller or manufacturer's customer support. Keep your purchase receipt as proof of purchase for warranty claims.
