SC07 Universal 2-Channel Garage Gate Receiver Module

1. ആമുഖം

The SC07 Universal 2-Channel Garage Gate Receiver Module is designed to provide versatile control for various automation systems. This module is compatible with a wide range of remote controls operating on frequencies between 300MHz and 900MHz, supporting both fixed and rolling code technologies. It is ideal for integration into gate automation systems, burglar alarm systems, electric doors, windows, and lifting equipment. Its compact design, low power consumption, and ease of connection make it a reliable solution for enhancing your existing control systems.

2 സ്പെസിഫിക്കേഷനുകൾ

3. പാക്കേജ് ഉള്ളടക്കം

• 1 x SC07 Receiver Module
• 1 x Small Antenna
• 1 x ഇംഗ്ലീഷ് മാനുവൽ

4. സജ്ജീകരണം

4.1 Power Input Selector (PIS)

The receiver operates on AC/DC 9V-30V. It is crucial to correctly set the Power Input Selector (PIS) based on your power supply voltage:

• ഇൻപുട്ട് വോള്യം ആണെങ്കിൽtage is greater than 24V, shorten pins 2 & 3.
• ഇൻപുട്ട് വോള്യം ആണെങ്കിൽtage is less than 24V, shorten pins 1 & 2.

4.2 വയറിംഗ് ഡയഗ്രം

Connect the receiver module to your gate automation system or other devices using the terminal block. Refer to the diagram below for connection points:

ചിത്രം: മുൻഭാഗം view of the white receiver module, showing PWR (Power Input), OUT1 (Output 1), OUT2 (Output 2), GND (Ground), and ANT (Antenna) terminals. Also visible are L1/L2 LEDs, S1/S2 learn buttons, and the 8-position DIP switch.

• PWR: Connect your AC/DC 9V-30V power supply here.
• OUT1 / CH1: Output for Channel 1 (relay output).
• OUT2 / CH2: Output for Channel 2 (relay output).
• GND: ഗ്രൗണ്ട് കണക്ഷൻ.
• എന്റ്: Connect the provided small antenna here for optimal signal reception.

5. പ്രവർത്തന നിർദ്ദേശങ്ങൾ

5.1 Brand Selection (DIP Switches)

The receiver features 8 DIP switches to select the correct brand and frequency for the remote control you wish to program. Each remote brand may require a specific DIP switch combination. Refer to the diagram below for common brand settings:

ചിത്രം: വിശദമായത് view of the 8-position DIP switch with various settings for different remote control brands and frequencies (e.g., Marantec, Hormann, Nice, etc.). Switches are labeled 1 through 8.

To select a brand, move the corresponding DIP switches UP or DOWN as indicated for your remote control's brand and frequency. For example, for a 433.92MHz Marantec remote control, move Dip-switch 7 UP.

5.2 Programming a New Remote Control

1. Select Brand: Ensure the correct brand and frequency are selected using the 8 DIP switches (refer to Section 5.1).
2. പഠന മോഡ് നൽകുക: Press the learn button (S1 for Channel 1, S2 for Channel 2) on the receiver module. The corresponding LED (L1 or L2) will turn on, indicating it's in learning mode.
3. Transmit Remote Signal: Press the desired button on your remote control. The LED on the receiver will flash 4 times, confirming successful programming.
4. Repeat for Additional Buttons: If your remote has multiple buttons you wish to program, repeat step 2 and 3 for each button.
5. രണ്ടാമത്തെ ചാനൽ: The programming procedure for the second channel (using S2 and L2) is identical.

5.3 എആർasing All Data from Memory

To clear all programmed remote controls from the receiver's memory:

• Press and hold either learn button (S1 or S2). The LED will begin to flash.
• Continue holding the button until the LED turns off. All saved data in the memory will be permanently erased and cannot be recovered.

6 ഉപയോക്തൃ നുറുങ്ങുകൾ

• വൈദ്യുതി വിതരണം: Always double-check your power supply voltage (AC/DC 9V-30V) and ensure the PIS (Power Input Selector) is correctly configured before powering on the module.
• ആൻ്റിന പ്ലേസ്മെൻ്റ്: For optimal reception range, ensure the small antenna is connected and positioned away from metal obstructions.
• പരിശോധന: After programming a remote, always test the range and functionality of the receiver before fully integrating it into your system.
• ഇടപെടൽ: The receiver is designed not to interfere with other remotes and receivers, but ensure your remote is transmitting on the correct frequency for the selected brand.

7. പ്രശ്‌നപരിഹാരം

• Remote Not Programming:
  • Verify that the DIP switches are set correctly for your remote control's brand and frequency.
  • Ensure your remote control has a working battery and is transmitting a signal.
  • Try erasing all data from the receiver's memory (Section 5.3) and then re-program the remote.
• ഹ്രസ്വ പ്രവർത്തന ശ്രേണി:
  • Check that the antenna is securely connected and not obstructed by metal objects.
  • Ensure there are no major sources of radio frequency interference nearby.
  • The stated range of 30-50 meters is for open areas; obstructions will reduce this.
• No Power to Receiver:
  • Check all wiring connections to the PWR and GND terminals.
  • Verify that your power supply is providing the correct voltage (9V-30V AC/DC).
  • Ensure the PIS (Power Input Selector) is correctly set for your voltage.
• Receiver Not Responding to Programmed Remote:
  • Confirm that the remote was successfully programmed (LED flashes 4 times).
  • Check if the remote's frequency matches the DIP switch settings.
  • Ensure the remote is not too far from the receiver.

8. പരിപാലനം

• വൃത്തിയാക്കൽ: മൊഡ്യൂൾ വൃത്തിയായും പൊടിയും അവശിഷ്ടങ്ങളും ഇല്ലാതെ സൂക്ഷിക്കുക. വൃത്തിയാക്കാൻ മൃദുവായതും ഉണങ്ങിയതുമായ തുണി ഉപയോഗിക്കുക.
• പരിസ്ഥിതി: Avoid exposing the module to extreme temperatures, high humidity, or direct water contact.
• വയറിംഗ് പരിശോധന: Periodically check all wiring connections for looseness or damage.

9. വാറൻ്റിയും പിന്തുണയും

For warranty information, technical support, or any questions not covered in this manual, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.