1. ഉൽപ്പന്നം കഴിഞ്ഞുview
The FOXEER Reaper Infinity 10W 80CH VTX is a high-power, switchable video transmitter designed for long-range RC FPV applications. It supports a wide input voltage range (2-8S Lipo) and offers multiple power output options from 400mW up to 10W across 80 channels in the 4.9G-6G frequency band. Featuring a CNC heat dissipation shell, built-in microphone, and cooling fan, this VTX is engineered for reliable performance in demanding environments.
2 സ്പെസിഫിക്കേഷനുകൾ
| ഫീച്ചർ | സ്പെസിഫിക്കേഷൻ |
|---|---|
| മോഡൽ | Reaper Infinity 10W |
| ഇൻപുട്ട് വോളിയംtage | 9-36V (2-8S Lipo) |
| Putട്ട്പുട്ട് വോളിയംtage | 5V |
| ചാനലുകൾ | 80CH |
| പവർ ഔട്ട്പുട്ട് | 1W / 2.5W / 5W / 7.5W / 10W (Switchable) |
| കുഴി മോഡ് | Yes (Double-click KEY button to toggle) |
| ഭാരം | 48 ഗ്രാം |
| മൗണ്ടിംഗ് ഹോൾ | 20*20mm M2 with 2.5mm depth |
| വലിപ്പം | 66*37*16എംഎം |
| ആന്റിന കണക്റ്റർ | എസ്.എം.എ |
| കേബിൾ കണക്റ്റർ | GH1.25 6P |
| ഉപഭോഗം | 19V/3.3A & 20V/1.5A, 10W |
| പാക്കേജിൽ ഉൾപ്പെടുന്നു | 1 x VTX, 1 x silicone cable |
Frequency Table (80 Channels)
| ബാൻഡ് | CH1 | CH2 | CH3 | CH4 | CH5 | CH6 | CH7 | CH8 |
|---|---|---|---|---|---|---|---|---|
| ബാൻഡ് എ | 5865 | 5845 | 5825 | 5805 | 5785 | 5765 | 5745 | 5725 |
| ബാൻഡ് ബി | 5733 | 5752 | 5771 | 5790 | 5809 | 5828 | 5847 | 5866 |
| ബാൻഡ് ഇ | 5705 | 5685 | 5665 | 5645 | 5885 | 5905 | 5925 | 5945 |
| ബാൻഡ് എഫ് | 5740 | 5760 | 5780 | 5800 | 5820 | 5840 | 5860 | 5880 |
| ബാൻഡ് ആർ | 5658 | 5695 | 5732 | 5769 | 5806 | 5843 | 5880 | 5917 |
| ബാൻഡ് എച്ച് | 5653 | 5693 | 5733 | 5773 | 5813 | 5853 | 5893 | 5933 |
| ബാൻഡ് എൽ | 5333 | 5373 | 5413 | 5453 | 5493 | 5533 | 5573 | 5613 |
| ബാൻഡ് യു | 5325 | 5348 | 5366 | 5384 | 5402 | 5420 | 5438 | 5456 |
| ബാൻഡ് ഒ | 5474 | 5492 | 5510 | 5528 | 5546 | 5564 | 5582 | 5600 |
| Band X | 4990 | 5020 | 5050 | 5080 | 5110 | 5140 | 5170 | 5200 |
3. സജ്ജീകരണ നിർദ്ദേശങ്ങൾ
3.1 വയറിംഗ് ഡയഗ്രം
Connect the VTX to your flight controller (FC) or power source according to the diagram below. Ensure correct polarity and voltagകേടുപാടുകൾ തടയാൻ ഇ.
- വീഡിയോ: Connect to the video input of your flight controller or camera.
- GND: നിലവുമായി ബന്ധിപ്പിക്കുക.
- 5V ഔട്ട്: Provides 5V output for powering a camera or other low-power devices.
- TRAMP: Connect to a UART TX pad on your flight controller for OSD control (SmartAudio/Tramp പ്രോട്ടോക്കോൾ).
- GND: നിലവുമായി ബന്ധിപ്പിക്കുക.
- 7-36V ഇൻ: Connect to your main battery voltage (2-8S Lipo).
3.2 മൗണ്ടിംഗ്
The VTX features 20x20mm M2 mounting holes with a 2.5mm depth. Use appropriate M2 screws and standoffs to securely mount the VTX to your frame, ensuring adequate airflow for cooling.
4. പ്രവർത്തന നിർദ്ദേശങ്ങൾ
4.1 Power and Frequency Adjustment
The VTX allows adjustment of power level and frequency. If the Tramp Rx pin cable on the VTX is connected to the Flight Controller (FC), then the physical button on the VTX will not work for adjustments. All adjustments should then be made via OSD (On-Screen Display) control through your FC.
- CH LED (Blue): Indicates the selected channel.
- FR LED (Green): Indicates the selected frequency band.
- PWR LED (Red): Indicates the power output level.
4.2 Pit Mode
To toggle Pit Mode on or off, double-click the "KEY" button on the VTX. When Pit Mode is active, the Red LED (PWR) will be off. When Pit Mode is off (normal operation), the Red LED (PWR) will be on.
4.3 BetaFlight Compatibility Note
BetaFlight firmware can typically only accept a maximum of 64 channels. If you are using BetaFlight, you may need to remove two frequency bands from the VTX configuration before inputting it into BetaFlight to ensure full compatibility and control.
5. പരിപാലനം
- വൃത്തിയായി സൂക്ഷിക്കു: Regularly clean the VTX, especially the cooling fan and heat sink, to ensure optimal heat dissipation. Use compressed air to remove dust and debris.
- ശാരീരിക സംരക്ഷണം: Avoid physical impacts or excessive force on the VTX, especially the antenna connector.
- ശരിയായ തണുപ്പിക്കൽ: Ensure the VTX has adequate airflow during operation, especially at higher power settings, to prevent overheating.
- കേബിൾ പരിശോധന: Periodically check all connected cables for wear, fraying, or loose connections.
6. പ്രശ്നപരിഹാരം
- വീഡിയോ സിഗ്നൽ ഇല്ല:
- Check all wiring connections, especially VIDEO and GND.
- Ensure the VTX is powered on (Red PWR LED should be on if not in Pit Mode).
- Verify that your FPV receiver is on the correct frequency and band.
- Confirm the camera is functioning and correctly connected.
- Poor Video Quality / Static:
- Check antenna connections on both VTX and receiver; ensure they are secure and undamaged.
- Try a different frequency channel or band.
- Ensure there are no obstructions between the VTX and receiver.
- Check for interference from other electronic components on your drone.
- Increase VTX power output if necessary (ensure adequate cooling).
- VTX അമിത ചൂടാക്കൽ:
- Ensure the cooling fan is operating correctly.
- Verify adequate airflow around the VTX.
- Consider reducing the power output if overheating persists in high-temperature environments.
- ഇൻപുട്ട് വോളിയം പരിശോധിക്കുകtagഇ; തെറ്റായ വാല്യംtage can cause excessive heat.
- Cannot Change Settings via Button:
- എങ്കിൽ Tramp Rx pin is connected to your FC, the button will be disabled. Use OSD control via your flight controller.
7 ഉപയോക്തൃ നുറുങ്ങുകൾ
- ആന്റിന തിരഞ്ഞെടുക്കൽ: Always use a properly matched antenna (e.g., 5.8GHz) with your VTX. Operating without an antenna can severely damage the unit.
- Cooling is Key: High power VTX units generate significant heat. Always ensure good airflow, especially when operating at 10W, to prevent thermal throttling and damage.
- SmartAudio/Tramp സജ്ജമാക്കുക: For convenient power and channel changes, configure SmartAudio or Tramp protocol on your flight controller. This allows adjustments directly from your OSD.
- പ്രാരംഭ പവർ-അപ്പ്: For initial setup and testing, it's recommended to start with a lower power output (e.g., 400mW or 1W) to minimize heat and potential interference.
8. വാറൻ്റിയും പിന്തുണയും
For warranty claims, technical support, or further assistance, please contact the manufacturer, FOXEER, or your authorized dealer. Keep your proof of purchase for warranty validation.
