Universal RX-MULTI Remote Control Receiver

ആമുഖം

The Universal RX-MULTI Receiver is a versatile 2-channel relay module designed to enhance or replace existing remote control systems for various applications. It operates across a wide frequency range of 300MHz to 868MHz and supports multiple encoding methods including Fixed Code, Rolling Code, and Learning Code. This receiver is ideal for controlling garage doors, gate openers, electric doors, windows, lifting equipment, and alarm systems, offering compatibility with a broad spectrum of remote control brands.

Figure 1: RX-MULTI Receiver Overview

സ്പെസിഫിക്കേഷനുകൾ

പാക്കേജ് ഉള്ളടക്കം

• RX-MULTI Receiver
• ചെറിയ ആന്റിന
• ഇംഗ്ലീഷ് മാനുവൽ

Note: Remote control batteries (CR2016x2, 3V) are not included with the remote control unit.

ചിത്രം 2: ഉദാample Remote Control (not included with receiver only purchase)

സജ്ജീകരണവും ഇൻസ്റ്റാളേഷനും

റിസീവർ വയറിംഗ്

The RX-MULTI receiver features terminals for power (PWR), two channels (CH1, CH2), ground (GND), and antenna (ANT). Connect the receiver to your gate automation system, garage door opener, or other device according to its specific wiring requirements. Ensure proper polarity for DC power connections.

Figure 3: RX-MULTI Receiver Internal Components

Power Input Selection (PIS)

The receiver supports an operating voltage of AC/DC 9V-30V. Adjust the Power Input Selector (PIS) pins based on your power supply:

• ഇൻപുട്ട് വോള്യം ആണെങ്കിൽtage is greater than 24V, shorten pins 2 & 3.
• ഇൻപുട്ട് വോള്യം ആണെങ്കിൽtage is less than 24V, shorten pins 1 & 2.

Replacing an Old Receiver or Adding New Remotes

The RX-MULTI can replace an existing garage door receiver or be added to an existing system to increase the number of supported remote controls. It can store up to 400 remote controls, significantly expanding your system's capacity.

Figure 4: Receiver Application Scenarios

പ്രോഗ്രാമിംഗ് നിർദ്ദേശങ്ങൾ

To program a new remote control to the RX-MULTI receiver, follow these steps:

1. Select Remote Brand/Frequency: Identify the correct brand and frequency for the remote control you wish to program. Use the 8 dip switches on the receiver to set the corresponding combination (UP or DOWN). For example, for 433.92MHz Flor-s remote controls, move Dip-switch 8 UP. Refer to the provided diagrams for common configurations.
2. Initiate Learning Mode: Press the 'Learn' button on the receiver. The LED indicator will turn on, signifying that the receiver is in learning mode.
3. Program Remote Button: Press the desired button on your remote control. The receiver's LED will flash 4 times, indicating successful programming of that button.
4. Repeat for Additional Buttons: If your remote has multiple buttons you wish to program, repeat step 2 and 3 for each additional button.
5. Second Channel Programming: The programming procedure for the second channel (CH2) is identical to the first channel (CH1).

Figure 5: Dip Switch Settings Examples (Part 1)

Figure 6: Dip Switch Settings Examples (Part 2)

Erasing All Stored Data

To erase all programmed remote controls from the receiver's memory:

• Press and hold either 'Learn' button on the receiver.
• The LED indicator will begin to flash. Continue holding the button.
• Release the button only after the LED turns off. All saved data will be permanently erased and cannot be recovered.

ഓപ്പറേഷൻ ഡെമോൺസ്ട്രേഷൻ

ട്രബിൾഷൂട്ടിംഗ്

• റിമോട്ട് പ്രതികരിക്കുന്നില്ല: Ensure the remote control has fresh batteries. Verify that the dip switches on the receiver are correctly set for the remote's frequency and encoding type. Re-attempt the programming steps.
• പരിമിതമായ ശ്രേണി: Check that the antenna is properly connected and extended. Ensure there are no major obstructions (e.g., thick walls, metal structures) between the remote and the receiver. Large electrical devices nearby can also cause interference.
• Programming failure: Double-check the dip switch settings. Ensure you are pressing the 'Learn' button correctly and observing the LED feedback. If multiple remotes are programmed, try erasing all data and reprogramming them one by one.
• No power to receiver: Verify the AC/DC 9V-30V power supply is connected correctly and providing the specified voltage. Check the Power Input Selector (PIS) pins are set appropriately for your voltage.

ഉപയോക്തൃ ടിപ്പുകൾ

re-യിൽ നിന്ന് പ്രത്യേക ഉപയോക്തൃ നുറുങ്ങുകളൊന്നും ലഭ്യമായിരുന്നില്ല.views or Q&A for this product. However, general advice for remote control receivers includes:

• Always test the range of your remote control after installation to ensure reliable operation.
• Keep a spare remote control or ensure multiple users have access to prevent being locked out.
• If you experience intermittent issues, check for potential sources of radio frequency interference in the vicinity.

മെയിൻ്റനൻസ്

The RX-MULTI receiver is designed for low maintenance. To ensure optimal performance and longevity:

• Keep the receiver in a dry environment, away from direct moisture and extreme temperatures.
• Periodically check wiring connections to ensure they are secure.
• Avoid exposing the unit to strong impacts or vibrations.
• Clean the exterior with a soft, dry cloth if necessary. Do not use harsh chemicals or abrasive cleaners.

പിന്തുണ

Should you encounter any issues during the installation, programming, or operation of your RX-MULTI receiver, please contact the seller for assistance. Support is available for troubleshooting and guidance on product usage. If the product experiences a quality issue, a satisfactory resolution will be provided within the agreed timeframe.