ആമുഖം
This manual provides comprehensive instructions for the setup, operation, and maintenance of your Yinuogo Garage Door / Gate Remote Control. Please read this manual carefully before attempting to program or use your new remote control to ensure proper functionality and safety.
സ്പെസിഫിക്കേഷനുകൾ
| ഫീച്ചർ | വിശദാംശങ്ങൾ |
|---|---|
| മോഡൽ നമ്പറുകൾ | YNG123, YNG300, YNG814 |
| എൻകോഡിംഗ് രീതി | റോളിംഗ് കോഡ് |
| Type of Programming | Programming with the receiver |
| ആവൃത്തി | 433.92MHz |
| ബട്ടണുകൾ | 2 or 4 (depending on model) |
| പരിധി | 30m-50m |
| ബാറ്ററി | ഉൾപ്പെടുത്തിയിട്ടുണ്ട് |
| ഉത്ഭവം | മെയിൻലാൻഡ് ചൈന |
| സർട്ടിഫിക്കേഷൻ | CE, FCC, RoHS, WEEE |
അനുയോജ്യമായ മോഡലുകൾ
This remote control is compatible with the following garage door and gate opener models:
- MITTO 2
- MITTO 4
- MITTO2A
- MITTO4A
- MITTO2M
- MITTO4M
- KLEIO B RCA 02
- KLEIO B RCA 04
- MITTO B RCB 02
- MITTO B RCB 04
- ത്ര്ച്൨൦
- ത്ര്ച്൨൦
- ത്ര്ച്൨൦
Important: Access to your receiver/opener is required for programming. Please ensure you have access before purchasing.
സജ്ജീകരണവും പ്രോഗ്രാമിംഗും
To program your new Yinuogo remote control, you will need to access the receiver unit of your garage door or gate opener. There are generally two types of programming procedures:
Programming Type 1 (Common for many receivers)
- സി തുറക്കുകasing of your receiver. It is typically located next to your motor.
- On the receiver circuit board, press the programming button (SW1). The LED light of the receiver will blink. Release the button.
- Press both buttons on your new remote control at the same time. Release them. The LED light of the receiver should remain lit fixedly.
- Press the left button on your new remote control. Release it. The LED light of the receiver will blink.
- Wait 5 seconds. The LED light of the receiver will turn off.
- Repeat this procedure for the right button of your new remote control. This time, use the programming button SW2 on the receiver.
- 10 സെക്കൻഡ് കാത്തിരിക്കുക.
- Your new remote control is programmed.
Programming Type 2 (For receivers with display, e.g., 'OK' button)
- നിങ്ങളുടെ റിസീവറിലെ "ശരി" ബട്ടൺ രണ്ടുതവണ അമർത്തുക. സ്ക്രീൻ "PARA" കാണിക്കുന്നു.
- Press the “-” button on your receiver twice. The screen displays “RADIO.”
- Press the “OK” button on your receiver once. The screen displays “ADI STRT.”
- നിങ്ങളുടെ റിസീവറിലെ "ശരി" ബട്ടൺ ഒരിക്കൽ അമർത്തുക. സ്ക്രീൻ "മറഞ്ഞിരിക്കുന്ന ബട്ടൺ" കാണിക്കുന്നു.
- Press both buttons on your new remote control at the same time. Keep them pressed down. The screen displays “Released”.
- Let the buttons go. The screen displays “Desired Button”.
- Press a button on your new remote control. The screen displays “OK”.
- 10 സെക്കൻഡ് കാത്തിരിക്കുക.
- Your new remote control is programmed.
Video Demonstration: Programming YNG123 and YNG300
നിങ്ങളുടെ റിമോട്ട് കൺട്രോൾ പ്രവർത്തിപ്പിക്കുന്നു
Once programmed, operating your Yinuogo remote control is straightforward:
- Press the desired button on the remote control to activate your garage door or gate opener.
- The LED indicator on the remote will light up when a button is pressed, confirming signal transmission.
മെയിൻ്റനൻസ്
Your Yinuogo remote control comes with a battery included. When the remote's range decreases significantly or the LED indicator fails to light up, it may be time to replace the battery. Refer to the product's internal design for battery type and replacement instructions. Ensure proper polarity when inserting a new battery.
ട്രബിൾഷൂട്ടിംഗ്
- പ്രോഗ്രാമിംഗിന് ശേഷം റിമോട്ട് പ്രവർത്തിക്കുന്നില്ല: Double-check all programming steps. Ensure you have access to the correct programming buttons (SW1/SW2 or OK/Minus) on your receiver. Verify that the receiver's LED responds as expected during programming.
- കുറച്ച ശ്രേണി: Replace the remote control's battery. Ensure there are no obstructions between the remote and the receiver.
- LED on remote not lighting up: റിമോട്ട് കൺട്രോളിന്റെ ബാറ്ററി മാറ്റിസ്ഥാപിക്കുക.
- Remote not compatible: Confirm your opener model is listed under 'Compatible Models'. If not, the remote may not work with your system.
ഉപയോക്തൃ ടിപ്പുകൾ
- Always ensure you have access to your receiver/opener unit before attempting to program a new remote.
- If you encounter difficulties with programming, consider searching for specific programming videos or guides for your exact garage door/gate opener model, as procedures can vary.
- Keep your remote control in a secure location, such as the provided clip for your car's visor, to prevent loss or damage.
വാറൻ്റിയും പിന്തുണയും
For any issues not covered in this manual, or if you require further assistance, please contact the seller directly. They can provide additional support, including specific learning videos if needed, to ensure your remote control functions correctly.
