Devoko Electric Standing Desk User Manual

1. ആമുഖം

Thank you for choosing the Devoko Electric Standing Desk. This manual provides detailed instructions for the assembly, operation, and maintenance of your new ergonomic workstation. Designed for comfort and productivity, this desk allows you to effortlessly switch between sitting and standing positions, promoting a healthier work environment.

Please read this manual carefully before use to ensure proper installation and safe operation.

2. പ്രധാനപ്പെട്ട സുരക്ഷാ മുന്നറിയിപ്പുകൾ

• ഉപയോഗിക്കുന്നതിന് മുമ്പ് ദയവായി ഈ മാനുവൽ ശ്രദ്ധാപൂർവ്വം വായിക്കുക.
• The product must be connected to the correct power supply (100-240Vac 50/60Hz).
• നിയന്ത്രണ ബോക്സുമായി ബന്ധിപ്പിച്ചിട്ടുള്ള ഏതെങ്കിലും ആക്സസറികൾക്കായി, പ്ലഗ് തരവും ഇലക്ട്രിക്കൽ സവിശേഷതകളും അതിൻ്റെ സ്പെസിഫിക്കേഷനുകൾക്ക് അനുസൃതമായിരിക്കണം.
• ഇൻഡോർ ഉപയോഗത്തിന് മാത്രം.
• If the transformer's external cable is damaged and needs to be replaced, a new accessory will be provided by the manufacturer or its service agent.
• ജോലി സമയത്ത് കുട്ടികളെയും വളർത്തുമൃഗങ്ങളെയും മേശയിൽ നിന്ന് അകറ്റി നിർത്തുക.
• Ensure there are no obstacles in the desk's path during height adjustments.

3 സ്പെസിഫിക്കേഷനുകൾ

4. പാക്കേജ് ഉള്ളടക്കം

Before assembly, please ensure all parts are present and undamaged. Refer to the diagram below for identification.

5. അസംബ്ലി നിർദ്ദേശങ്ങൾ

Follow these steps carefully to assemble your Devoko Electric Standing Desk.

Step 1: Attach Frame Supports to Lifting Columns

Attach the frame supports (G) to the lifting columns (E) using S4 Allen wrench and M6*30 screws (2). Ensure they are securely fastened.

ഘട്ടം 2: സൈഡ് റെയിലുകൾ ബന്ധിപ്പിക്കുക

Connect the two side rails (H and J) together using M6*10 screws (5). Slide them into place as shown.

Step 3: Attach Frame to Lifting Columns

Secure the assembled frame to the lifting columns using M6*12 screws (1). Repeat for both sides.

Step 4: Install Crossbar

Attach the crossbar (D) to the frame using M6*12 screws (1).

ഘട്ടം 5: ഡ്രൈവ് വടി ചേർക്കുക

Insert the drive rod (M) into the designated slots, ensuring it connects both lifting mechanisms.

Step 6: Final Frame Connections

Ensure all frame connections are tight and secure. Refer to the diagram for a complete view of the frame assembly.

Step 7: Attach LED Control Panel

Attach the LED control panel (L) to the side of the desktop frame using M6*12 screws (1).

Step 8: Place Desktop Sections

Place the desktop sections (A, B, C) onto the assembled frame. Use Φ8*30 dowels (6) to align and secure the sections.

Step 9: Attach Control Box

Attach the control box (K) to the underside of the desktop using ST5*13 screws (4).

Step 10: Secure Desktop to Frame

Secure the desktop to the frame using M6*50 screws (3).

Step 11: Final Desktop Fastening

Use remaining ST5*13 screws (4) to further secure the desktop to the frame.

ഘട്ടം 12: കേബിൾ മാനേജ്മെൻ്റ്

Use the provided cable clips (8) to organize and secure the power cable (N) and any other cables, ensuring they do not interfere with the desk's movement.

6. പ്രവർത്തന നിർദ്ദേശങ്ങൾ

6.1 കൺട്രോൾ പാനൽ ഓവർview

The LED control panel allows you to adjust the desk height and save preferred positions. The entire handset surface is a button panel. If there is no press within 10 seconds, the handset enters a dormant state. Press any key to wake it up.

• ഡിസ്പ്ലേ സ്ക്രീൻ: Shows the current height value of the desk.
• Up (^) & Down (v) Keys: Press and hold these keys to adjust the desk height until you reach your desired position.
• Memory Keys (1/2/3): After setting memory keys, the desk can automatically lift to the stored height.
• 'M' Key: Used for setting memory positions and accessing advanced functions.

6.2 Setting Memory Mode

1. Adjust the desk to your desired height using the Up (^) or Down (v) keys.
2. Press the 'M' key. The display screen will show "S-" and a flashing number.
3. Within 3 seconds, press one of the memory keys (1, 2, or 3) to save the current height to that preset. The memory height is successfully saved.
4. To use a saved position, simply press the corresponding memory key (1, 2, or 3), and the desk will automatically move to that height.

6.3 പ്രാരംഭം

Initialization is required after initial setup or if the desk encounters an error. There are two methods:

Method 1: Standard Initialization

1. When "RST" is displayed on the screen, press and hold the Down (v) key until the desk frame reaches its lowest point.
2. After the display screen shows numbers and the desk frame rebounds slightly, the initialization is complete.
3. പ്രധാനപ്പെട്ടത്: Do not release the Down (v) key during this operation, or the initialization will fail.

Method 2: Forced Initialization (if standard initialization fails)

1. Press and hold the Down (v) key until the desk frame reaches its lowest point. Release the key.
2. Immediately press and hold the Down (v) key again for about 5 seconds until "RST" flashes on the display screen, and then numbers are shown again. The desk frame will rebound, indicating initialization is complete.

ഫാക്ടറി ക്രമീകരണങ്ങൾ പുനഃസ്ഥാപിക്കുന്നു

If a new controller is installed or parameters need to be restored to factory settings:

Press and hold both the Up (^) and Down (v) keys simultaneously. The numbers will flash on the display screen after about 5 seconds, then "RST" will blink after 10 seconds. Proceed with Method 1 (Standard Initialization).

7. വിപുലമായ പ്രവർത്തനങ്ങൾ

7.1 Limited Height Setting

This function allows you to set a maximum or minimum height limit for the desk.

1. Adjust the desk to the desired limit height.
2. Press and hold both the Up (^) and Down (v) keys simultaneously for 5 seconds until the numbers flash on the display screen. Release the keys immediately. The height limit is now set.
3. To cancel the limit: Run the desk to the limit height, then press and hold both the Up (^) and Down (v) keys again for 5 seconds until the numbers flash. Release the keys immediately. The limit is canceled.

7.2 ലോക്ക് ആൻഡ് അൺലോക്ക്

This feature prevents accidental height adjustments.

• ലോക്ക് ചെയ്യാൻ: Press and hold the 'M' key and '1' key simultaneously for 5 seconds. The screen will display "LOC", indicating the system is locked.
• അൺലോക്ക് ചെയ്യാൻ: Press and hold the 'M' key and '1' key simultaneously for 5 seconds. The screen will change from "LOC" to a number, indicating the system is unlocked.

7.3 Anti-Collision Sensitivity

For safety, the desk will stop and rebound slightly if it encounters an obstacle during height adjustment. You can adjust the sensitivity of this feature.

1. Press and hold the 'M' key for about 5 seconds until the screen displays "S-1". This enters the setting function.
2. Use the Up (^) or Down (v) keys to navigate to "S-3" (Up anti-collision sensitivity) or "S-4" (Down anti-collision sensitivity).
3. Press 'M' to select. Use Up (^) or Down (v) to adjust the sensitivity from 0 (shut down) to 8 (most sensitive).
4. Press 'M' again to confirm the setting.
5. Press 'M' repeatedly to exit the setting menu and return to the numerical display.

കുറിപ്പ്: If the sensitivity is too high, the anti-collision feature may trigger unnecessarily. If it triggers too often, you may need to reduce the sensitivity.

8. പ്രശ്‌നപരിഹാരം

If your desk encounters an issue, the LED display may show an error code. Refer to the table below for common error codes and their solutions.

9. പരിപാലനം

• മേശയുടെ പ്രതലം മൃദുവായ, ഡി-ക്ലാസ്സർ ഉപയോഗിച്ച് പതിവായി വൃത്തിയാക്കുക.amp തുണി. ഉരച്ചിലുകൾ ഉണ്ടാക്കുന്ന ക്ലീനറുകളോ കഠിനമായ രാസവസ്തുക്കളോ ഒഴിവാക്കുക.
• എല്ലാ സ്ക്രൂകളും കണക്ഷനുകളും ഇറുകിയതായി ഉറപ്പാക്കാൻ ഇടയ്ക്കിടെ പരിശോധിക്കുക.
• Keep the area around the desk legs clear of obstructions to ensure smooth operation.
• Do not overload the desk beyond its maximum static load capacity of 80 KG.

10 ഉപയോക്തൃ നുറുങ്ങുകൾ

• To maximize the ergonomic benefits, alternate between sitting and standing positions throughout your workday.
• Utilize the memory presets to quickly switch to your preferred sitting and standing heights.
• If the anti-collision feature triggers too frequently, consider reducing its sensitivity in the advanced settings.
• Ensure all cables are properly managed to prevent entanglement and damage during height adjustments.

11. വാറൻ്റിയും പിന്തുണയും

Your Devoko Electric Standing Desk comes with a standard manufacturer's warranty. For specific warranty details, please refer to the documentation provided at the time of purchase or contact Devoko customer support.

If you encounter any issues not covered in the troubleshooting section or require further assistance, please contact Devoko customer service. Provide your product model and a detailed description of the issue for efficient support.