M9 മൾട്ടി-ഫ്രീക്വൻസി ഗാരേജ് ഡോർ റിമോട്ട് കൺട്രോൾ ഡ്യൂപ്ലിക്കേറ്റർ യൂസർ മാനുവൽ

ആമുഖം

The M9 Multi-Frequency Remote Control Duplicator is a versatile device designed to copy and transmit signals from various fixed code remote controls operating within the 300-980MHz frequency range. This manual provides detailed instructions on how to set up, operate, and maintain your duplicator, ensuring optimal performance and ease of use for garage doors, gates, and other compatible systems.

Image: Two M9 remote control duplicators (gold and silver) with keychains, front view.

സ്പെസിഫിക്കേഷനുകൾ

ആമുഖം

Before first use, ensure your M9 remote control duplicator is adequately charged using the provided 5V TPC-C charging interface. A full charge ensures stable operation and optimal remote control distance.

Image: Silver M9 remote control duplicator with keychain, displaying '20' on the LED screen.

ഓപ്പറേഷൻ

The M9 duplicator features a multi-channel design and an LED display to indicate operation status. Refer to the button diagram below for button identification.

Image: Diagram illustrating the button layout and functions of the M9 remote control duplicator.

1. Clearing Existing Codes

1. Press and hold button 1 (top left) and button 2 (top right) simultaneously.
2. Continue holding for approximately 2 seconds until the LED indicator flashes rapidly.
3. രണ്ട് ബട്ടണുകളും റിലീസ് ചെയ്യുക.
4. കുറിപ്പ്: The LED light must continue flashing after you release your hand. If it does not flash for a long time, it indicates that the two buttons were not pressed simultaneously. Repeat the operation.
5. After successful clearing, pressing any key on the remote control will cause the indicator light to flash briefly and then go out, confirming that the code clearing is successful.

2. Copying Remote Codes

1. Ensure the M9 duplicator has been cleared of all previous codes (see 'Clearing Existing Codes' above).
2. Place your original remote control and the M9 duplicator side-by-side, as close as possible.
3. Press and hold the desired button on your original remote control.
4. Simultaneously, press and hold the corresponding button on the M9 duplicator where you wish to store the code.
5. Observe the LED display on the M9 duplicator. When the channel number on the display tube remains constantly lit, it indicates that the copy is successful.
6. രണ്ട് ബട്ടണുകളും റിലീസ് ചെയ്യുക.
7. Repeat this process for any remaining keys you wish to copy.
8. കുറിപ്പ്: During the copying process, do not release the buttons on either remote control until the display tube number on the M9 duplicator is continuously lit.

3. Restoring Codes

If you accidentally clear the copied codes from your M9 remote control, you can restore them:

1. Simultaneously press and hold the bottom two keys (the '+' and '-' buttons on the bottom row) of the M9 duplicator.
2. Wait for approximately 2 seconds until the LED indicator flashes rapidly.
3. നിങ്ങളുടെ കൈ വിടൂ.
4. After recovery, pressing any key on the remote control will cause its indicator light to remain constantly on, confirming the codes have been restored.

4. Channel Locking

To prevent accidental changes to a copied channel, you can lock it:

1. Press and hold the second button in the first row (the 'square' button) and the first button in the middle row (the '+' button) simultaneously.
2. If the LED light flashes quickly, the channel is successfully locked.
3. Once a channel is locked, it cannot be switched or overwritten.
4. To cancel the lock, repeat the same procedure.

മെയിൻ്റനൻസ്

• ഉപകരണം വരണ്ടതായി സൂക്ഷിക്കുക. ഈർപ്പം ആന്തരിക സർക്യൂട്ടുകളെ തകരാറിലാക്കും.
• Avoid extreme temperatures. High temperatures can shorten the life of electronic devices.
• ഉപകരണം ഉപേക്ഷിക്കുകയോ തട്ടുകയോ കുലുക്കുകയോ ചെയ്യരുത്. പരുക്കൻ കൈകാര്യം ചെയ്യുന്നത് ആന്തരിക സർക്യൂട്ട് ബോർഡുകൾ തകർക്കും.
• മൃദുവായതും ഉണങ്ങിയതുമായ തുണി ഉപയോഗിച്ച് ഉപകരണം വൃത്തിയാക്കുക. കഠിനമായ രാസവസ്തുക്കളോ ക്ലീനിംഗ് ലായകങ്ങളോ ഉപയോഗിക്കരുത്.
• പതിവായി ഉപയോഗിക്കുന്നില്ലെങ്കിലും, ബാറ്ററിയുടെ ആരോഗ്യം നിലനിർത്താൻ ഉപകരണം പതിവായി ചാർജ് ചെയ്യുക.

ട്രബിൾഷൂട്ടിംഗ്

• Remote not copying: Ensure the original remote is a fixed code type and operates within the 300-980MHz frequency range. Verify that the clearing process was successful before attempting to copy. Make sure both remotes are very close during copying.
• Short operating distance: Check the battery level of the M9 duplicator. Ensure there are no significant obstructions between the duplicator and the receiver.
• LED not flashing during clearing/restoring: Ensure buttons are pressed simultaneously and held for the required duration. Repeat the process carefully.
• പൊരുത്തക്കേട്: This duplicator is designed for fixed code remotes. It may not be compatible with rolling code or encrypted remotes.

ഉപയോക്തൃ ടിപ്പുകൾ

• അനുയോജ്യത പരിശോധിക്കുക: Before attempting to duplicate, always verify that your existing remote control uses a fixed code and operates within the 300-980MHz frequency range. For example, some users have inquired about compatibility with specific models like the ATX PTX5V2 Tricode remote for roller doors; please confirm your original remote's specifications.
• Optimal Copying Position: For best results during the copying process, position the M9 duplicator and the original remote control as close as possible, ideally touching, to ensure a strong signal transfer.
• Practice Clearing First: It's recommended to practice the code clearing procedure a few times to become familiar with the button presses and LED feedback before attempting to copy new codes.

വാറൻ്റിയും പിന്തുണയും

This product is covered by a standard manufacturer's warranty against defects in materials and workmanship. For technical support, troubleshooting assistance, or warranty claims, please contact the retailer or manufacturer directly. Keep your purchase receipt as proof of purchase.