Antec NX400 NX Series Mid-Tower ATX Gaming Case Instruction Manual

ആമുഖം

The Antec NX400 is a versatile mid-tower ATX gaming case designed for PC enthusiasts and gamers. It offers a blend of aesthetic appeal with its tempered glass side panel and ARGB lighting, alongside practical features for component installation and cooling. This manual provides essential information for setting up, operating, and maintaining your Antec NX400 case.

ചിത്രം 1: മുൻഭാഗം view of the Antec NX400 Mid-Tower ATX Gaming Case, showcasing its tempered glass side panel and front ARGB LED strip.

പ്രധാന സവിശേഷതകൾ

• മദർബോർഡ് പിന്തുണ: Compatible with ATX motherboards.
• ഉൾപ്പെടുത്തിയ ഫാൻ: Features 1 x 120 mm ARGB fan pre-installed in the rear for immediate cooling and lighting.
• റേഡിയേറ്റർ പിന്തുണ: Extensive liquid cooling support with space for up to a 360 mm radiator in the front, 240 mm on top, and 140 mm in the rear.
• ഡ്രൈവ് ബേസ്: Supports versatile storage configurations with up to 2 x 3.5" HDDs / 2.5" SSDs (convertible) and 4 x 2.5" SSDs.
• സൈഡ് പാനൽ: Equipped with a tempered glass side panel to showcase your internal components and ARGB lighting.
• ഫ്രണ്ട് പാനൽ കണക്റ്റിവിറ്റി: Includes 1 x USB 2.0 port and 2 x USB 3.0 ports for convenient peripheral connection.
• ARGB നിയന്ത്രണം: Dedicated LED mode button on the front panel allows for easy cycling through various ARGB lighting effects.

Figure 2: Detail of the multi-mode ARGB light bar on the front panel and the included 120mm ARGB fan in the rear of the NX400 case.

Figure 3: The dedicated LED control button located on the top I/O panel, allowing for easy customization of ARGB effects.

സജ്ജീകരണവും ഇൻസ്റ്റാളേഷനും

Before beginning installation, ensure you have all necessary components and tools. Refer to your motherboard and component manuals for specific installation instructions.

1. അൺപാക്കിംഗും തയ്യാറാക്കലും

• കേസ് അതിന്റെ പാക്കേജിംഗിൽ നിന്ന് ശ്രദ്ധാപൂർവ്വം നീക്കം ചെയ്യുക.
• Remove the tempered glass side panel by unscrewing the four thumb screws. Place it on a soft, flat surface to prevent scratches.
• Identify the included accessory box containing screws and cable ties. Note that screws may be mixed; refer to component manuals for correct screw types.

2. മദർബോർഡ് ഇൻസ്റ്റാളേഷൻ

• Install the I/O shield (if not pre-attached to your motherboard) into the rear opening of the case.
• Align your ATX motherboard with the pre-installed standoffs inside the case.
• Secure the motherboard using the appropriate screws (typically those with a round head and a lip).

3. പവർ സപ്ലൈ യൂണിറ്റ് (പി‌എസ്‌യു) ഇൻസ്റ്റാളേഷൻ

• The NX400 supports PSUs up to 170 mm in length.
• Slide the PSU into the dedicated compartment at the bottom rear of the case.
• Secure the PSU from the rear of the case using the provided screws.

4. സ്റ്റോറേജ് ഡ്രൈവ് ഇൻസ്റ്റാളേഷൻ

• Install 3.5" HDDs or 2.5" SSDs into the drive cages located beneath the PSU shroud or behind the motherboard tray.
• The case provides dedicated mounts for up to four 2.5" SSDs.

5. ഫാൻ, റേഡിയേറ്റർ ഇൻസ്റ്റാളേഷൻ

• The case comes with one 120mm ARGB fan pre-installed in the rear.
• Additional fan support: Front (3 x 120mm or 2 x 140mm), Top (2 x 120mm or 2 x 140mm), Rear (1 x 120mm or 1 x 140mm).
• Radiator support: Front (up to 360mm), Top (up to 240mm), Rear (up to 140mm).

Figure 4: Diagram illustrating the fan and radiator mounting options within the Antec NX400 case.

6. ഗ്രാഫിക്സ് കാർഡും സിപിയു കൂളറും ഇൻസ്റ്റാൾ ചെയ്യൽ

• The case supports graphics cards up to 330 mm in length.
• CPU coolers with a maximum height of 170 mm are supported.

Figure 5: Internal layout showing maximum dimensions for CPU cooler, GPU, and PSU, along with motherboard and SSD/HDD locations.

7. കേബിൾ മാനേജ്മെന്റ്

• Utilize the cutouts and tie-down points behind the motherboard tray to route and secure cables for a clean build and improved airflow.
• Connect the front panel I/O cables (USB, audio, power, reset, LED) to the appropriate headers on your motherboard.
• Ensure the ARGB fan and front LED strip are connected. The fan typically uses a Molex connector, and the front LED strip uses a SATA power connector. These must be connected directly to your PSU.

ഓപ്പറേഷൻ

The Antec NX400 features an intuitive front I/O panel for easy access to essential controls and ports.

ഫ്രണ്ട് I/O പാനൽ

• പവർ ബട്ടൺ: സിസ്റ്റം ഓൺ അല്ലെങ്കിൽ ഓഫ് ചെയ്യാൻ അമർത്തുക.
• റീസെറ്റ് ബട്ടൺ: സിസ്റ്റം പുനരാരംഭിക്കാൻ അമർത്തുക.
• LED നിയന്ത്രണ ബട്ടൺ: Cycle through various pre-programmed ARGB lighting effects for the front LED strip and the included rear fan. A single press changes the effect.
• MIC/AUDIO Jacks: നിങ്ങളുടെ ഹെഡ്‌ഫോണുകളും മൈക്രോഫോണും ബന്ധിപ്പിക്കുക.
• USB 2.0 പോർട്ട് (x1): USB 2.0 അനുയോജ്യമായ ഉപകരണങ്ങൾ ബന്ധിപ്പിക്കുന്നതിന്.
• USB 3.0 പോർട്ടുകൾ (x2): For high-speed data transfer with USB 3.0 compatible devices.

ചിത്രം 6: ഓവർview of the top-mounted I/O ports, including power, reset, LED control, audio jacks, and USB ports.

ഉൽപ്പന്നം കഴിഞ്ഞുview വീഡിയോ

മെയിൻ്റനൻസ്

Regular maintenance helps ensure optimal performance and longevity of your Antec NX400 case.

• പൊടി വൃത്തിയാക്കൽ: Periodically clean dust filters (if present) and internal components using compressed air or a soft brush. This prevents dust buildup, which can impede airflow and component cooling.
• ടെമ്പർഡ് ഗ്ലാസ് കെയർ: Clean the tempered glass side panel with a microfiber cloth and a non-abrasive glass cleaner. Avoid harsh chemicals or abrasive materials that could scratch the glass.
• കേബിൾ മാനേജുമെന്റ്: Occasionally check cable routing to ensure no cables are obstructing airflow or fan blades.

ട്രബിൾഷൂട്ടിംഗ്

This section addresses common issues you might encounter with your Antec NX400 case.

1. ARGB Lighting Not Working or Incorrect Colors

• കണക്ഷനുകൾ പരിശോധിക്കുക: Ensure the front LED strip and the included ARGB fan are properly connected to their respective power sources (SATA for LED strip, Molex for fan) and to the case's internal LED controller.
• LED Button Functionality: Press the LED control button on the front I/O panel multiple times to cycle through effects. If no change occurs, verify the LED control cable is correctly connected to the motherboard or controller.

2. അമിതമായ ഫാൻ ശബ്ദം

• ഉൾപ്പെടുത്തിയ ഫാൻ: The included rear fan is connected via Molex, which typically means its speed is not controllable by the motherboard. If the fan is too loud, consider replacing it with a PWM or DC controllable fan connected to your motherboard.
• തടസ്സങ്ങൾ: Check for any cables or debris obstructing fan blades.
• മൗണ്ടിംഗ്: Ensure all fans are securely mounted to prevent vibrations.

3. Front Panel USB/Audio Ports Not Functioning

• ആന്തരിക കണക്ഷനുകൾ: Verify that the USB and audio cables from the front I/O panel are securely connected to the correct headers on your motherboard. Refer to your motherboard manual for header locations.

4. Missing or Mixed Screws

• The case includes a single bag with various screw types. Refer to your component manuals (motherboard, PSU, drives) to identify the correct screws for each part. Common types include screws for motherboard standoffs (round head with lip), PSU mounting, and drive installation.

സാങ്കേതിക സവിശേഷതകൾ

വാറൻ്റിയും പിന്തുണയും

For warranty information, technical support, or service inquiries regarding your Antec NX400 case, please refer to the official Antec website or contact Antec customer support directly. Keep your proof of purchase for warranty claims.

ഔദ്യോഗിക ആന്റക് Webസൈറ്റ്: www.antec.com