ആമുഖം
This manual provides detailed instructions for the safe and efficient operation of your JAMARA Profi HF-40 II Speed Controller. Please read this manual thoroughly before use and retain it for future reference. This device is designed for use in remote-controlled models and requires careful handling and correct installation.
ഉൽപ്പന്നം കഴിഞ്ഞുview
ചിത്രം 1: The JAMARA Profi HF-40 II Speed Controller. It features a grey casing with prominent red heat sinks on top for thermal management. The front panel shows 'Profi HF 40 II', 'NEU. HI.' indicators, a 'CE' mark, and a 'ONE-TOUCH SET UP' button. Various colored wires (blue, black, red, white) extend from one side, indicating connections for motor, battery, and receiver.
The JAMARA Profi HF-40 II is an electronic speed controller (ESC) designed for remote-controlled applications. It manages the power delivery from the battery to the motor, allowing for precise control of speed and direction. Key features include efficient heat dissipation via integrated heat sinks and a simplified one-touch setup process.
സ്പെസിഫിക്കേഷനുകൾ
| മോഡൽ നമ്പർ: | Jamara_81300 |
| ബ്രാൻഡ്: | ജമാര |
| ആവൃത്തി: | 1 kHz |
| Cells (Voltage Range): | 5-10 cells (6-12 V) |
| RDS (On-Resistance): | 0.009 ഓം |
| സ്ഥിരമായ കറൻ്റ്: | 40 A (maximum 5 minutes) |
| അളവുകൾ (L x W x H): | 48 x 41 x 26 മിമി |
| ഭാരം: | 100 ഗ്രാം |
| ശുപാർശ ചെയ്യുന്ന പ്രായം: | 14 വയസ്സും അതിൽ കൂടുതലും |
| ബാറ്ററി തരം: | Rechargeable battery pack (not included) |
| റിമോട്ട് കൺട്രോൾ: | Radio type, 4 channels, 4 frequency bands |
| ഉപയോഗ പരിസ്ഥിതി: | ഇൻഡോർ, ഔട്ട്ഡോർ ഉപയോഗത്തിന് അനുയോജ്യം |
സജ്ജമാക്കുക
- മൗണ്ടിംഗ്: Securely mount the speed controller in your model using appropriate fasteners or double-sided tape. Ensure adequate airflow around the heat sinks for optimal cooling.
- മോട്ടോർ കണക്ഷൻ: Connect the motor wires to the corresponding output terminals on the speed controller. Refer to your motor's manual for correct polarity if applicable.
- ബാറ്ററി കണക്ഷൻ: Connect the battery pack to the speed controller's power input. Ensure correct polarity to prevent damage. Use only battery types within the specified voltagഇ ശ്രേണി (6-12V).
- റിസീവർ കണക്ഷൻ: Plug the speed controller's signal cable into the throttle channel of your RC receiver.
- Calibration (One-Touch Setup):
- Ensure your transmitter's throttle trim is at neutral and the throttle stick is at the neutral position.
- Power on the transmitter, then power on the model.
- Press and hold the "ONE-TOUCH SET UP" button on the speed controller (refer to Figure 1).
- Follow the indicator lights (NEU. HI.) as per the specific calibration sequence detailed in the full manufacturer's guide. This typically involves setting neutral, full throttle, and full brake positions.
- Release the button once calibration is complete.
പ്രവർത്തന നിർദ്ദേശങ്ങൾ
After successful setup and calibration, follow these steps for operation:
- പവർ ഓൺ സീക്വൻസ്: Always turn on your transmitter first, then connect the battery to the model.
- ത്രോട്ടിൽ നിയന്ത്രണം: Use the throttle stick on your transmitter to control the motor speed. Moving the stick forward typically increases speed, while pulling it back applies brakes or reverse (if configured).
- പവർ ഓഫ് ക്രമം: Always disconnect the battery from the model first, then turn off your transmitter.
- നിരീക്ഷണം: Observe the model's behavior and the speed controller's temperature during operation. If the controller becomes excessively hot, allow it to cool down before further use.
മെയിൻ്റനൻസ്
- വൃത്തിയാക്കൽ: Regularly clean the speed controller, especially the heat sinks, to remove dust, dirt, and debris. Use a soft brush or compressed air. Do not use liquids.
- പരിശോധന: Periodically inspect all wires and connectors for signs of wear, damage, or corrosion. Ensure all connections are secure.
- സംഭരണം: Store the speed controller in a dry, cool environment away from direct sunlight and extreme temperatures.
ട്രബിൾഷൂട്ടിംഗ്
| പ്രശ്നം | സാധ്യമായ കാരണം | പരിഹാരം |
|---|---|---|
| Motor does not respond. | Incorrect wiring, uncalibrated ESC, low battery, transmitter off. | Check all connections, recalibrate the ESC, charge battery, ensure transmitter is on. |
| ESC അമിതമായി ചൂടാകുന്നു. | Insufficient airflow, motor overload, incorrect gearing. | Ensure proper ventilation, check motor/gearing for appropriate load. |
| Erratic motor behavior. | Interference, loose connections, faulty receiver signal. | Check for sources of interference, secure all connections, test with another receiver if possible. |
സുരക്ഷാ വിവരങ്ങൾ
- പൊതു സുരക്ഷ: Always operate your model in a safe environment, away from people, animals, and obstacles.
- ബാറ്ററി സുരക്ഷ: Use only recommended battery types and chargers. Never short-circuit batteries or expose them to extreme temperatures. Disconnect batteries when not in use.
- ചൂട്: The speed controller and motor can become very hot during operation. Avoid touching them immediately after use to prevent burns.
- വാട്ടർ എക്സ്പോഷർ: This speed controller is not waterproof unless explicitly stated by the manufacturer. Avoid exposure to moisture.
- കുട്ടികൾ: This product is not a toy and is recommended for users aged 14 and older due to its complexity and potential hazards. Adult supervision is advised for younger users.
വാറൻ്റിയും പിന്തുണയും
For warranty information, please refer to the documentation provided with your purchase or contact your retailer. For technical support, please visit the official Jamara webസൈറ്റ് അല്ലെങ്കിൽ അവരുടെ ഉപഭോക്തൃ സേവന വിഭാഗവുമായി ബന്ധപ്പെടുക.