Intermatic EI200LA Electronic In-Wall Countdown Auto-Off Timer User Manual

ആമുഖം

The Intermatic EI200LA Electronic In-Wall Countdown Auto-Off Timer is designed to replace standard toggle-style wall switches, providing silent electronic timing operation. This timer offers time ranges of 5, 10, 15, and 30 minutes, making it suitable for various applications such as indoor/outdoor lighting, exhaust fans, and other electrical loads. This manual provides essential information for safe installation, operation, and maintenance of your timer.

ഫീച്ചറുകൾ

• Provides 5/10/15/30 Minute time ranges.
• Available in Light Almond finish.
• Offers silent operation.
• Replaces single-pole switches in a variety of applications.
• CFL compatible with all EI200 series timers (EI210W, EI220W, etc.), EI500C, EI500WC, EI500LAC, EI600C and EI600LAC.
• Designed for use with a decorator-style wall plate (NOT included).

ഇലക്ട്രിക്കൽ റേറ്റിംഗുകൾ

• 120 VAC, 60 Hz
• 15A General Purpose
• 1000W ടങ്സ്റ്റൺ
• 1/4 എച്ച്പി മോട്ടോർ
• 1000 VA ബാലസ്റ്റ്

ഇൻസ്റ്റലേഷൻ നിർദ്ദേശങ്ങൾ

മുന്നറിയിപ്പ്: തീയോ ആഘാതമോ മരണമോ ഒഴിവാക്കാൻ, സർക്യൂട്ട് ബ്രേക്കറിൽ പവർ ഓഫ് ചെയ്‌ത് വയറിംഗിന് മുമ്പ് പവർ ഓഫാണോയെന്ന് പരിശോധിക്കുക.

Lead Wire Identification:

• കറുപ്പ്: ലൈൻ/ഹോട്ട്
• വെള്ള: നിഷ്പക്ഷ
• ചുവപ്പ്: ലോഡ് ചെയ്യുക
• പച്ച: ഗ്രൗണ്ട്

1. Remove wall plate and disconnect light switch. Make sure both "hot" and neutral wires are present in the junction box. (See Fig. 1). If both wires are not present, additional wiring may be necessary before installation can be completed.
2. Connect red timer wire to wire from fixture using wire connector. Connect black timer wire to the "hot" (usually black or red) wire in junction box using wire connector. Cut white wire in junction box (or green splice) and strip 3/8" of insulation on both wires. Connect white timer wire to white wire in junction box using wire connector. (See Fig. 2).
3. If the wall switch you are replacing had separate grounding conductors connected to the GREEN screw on the switch, make sure to connect these to the green wire from the timer with a wire connector.
4. എല്ലാ വയർ കണക്ഷനുകളും സുരക്ഷിതമാണോയെന്ന് പരിശോധിക്കുക.
5. Place all wires inside junction box. Fit timer into junction box. Next, install timer using (2) mounting screws furnished.
6. Reconnect your electrical power.

Figure 1 & 2: Wiring diagrams for the EI200LA timer. Figure 1 illustrates the timer's internal connections, while Figure 2 shows the typical wiring setup within a wall box, connecting the timer to the fixture and power supply.

ഓപ്പറേഷൻ

ടൈമർ മോഡ്

To enter Timer mode, press and release the push button (for less than 2 seconds) repeatedly to select one of the four time settings: OFF (5 minutes - 10 minutes - 15 minutes - 30 minutes) - OFF. The illuminated LED indicates which time setting is selected and the connected load is turned ON. Timer starts counting down until time out is reached, all 5 LED's go off and the connected load turns OFF.

ഹോൾഡ് മോഡ് (തുടർച്ചയുള്ള പ്രവർത്തനം)

To turn timer ON for extended periods of time, press and hold the push button for more than 2 seconds. Timer enters HOLD mode, HOLD LED turns on, and the connected load is turned ON. To exit HOLD mode press and release the push button, all 5 LED's go off and the connected load turns OFF.

Image of the Intermatic EI200LA timer face, showing the push button and LED indicators for 5, 10, 15, 30 minutes, and HOLD mode.

മെയിൻ്റനൻസ്

The Intermatic EI200LA timer is designed for maintenance-free operation. To ensure longevity and proper function, keep the device clean and free from dust. Do not use abrasive cleaners or solvents. If the device requires cleaning, gently wipe the surface with a soft, damp cloth. Ensure power is disconnected at the circuit breaker before any cleaning or inspection.

ട്രബിൾഷൂട്ടിംഗ്

• Timer not responding: Ensure power is supplied to the circuit. Check the circuit breaker. Verify all wiring connections are secure according to the installation instructions.
• Load not turning ON/OFF: Confirm the timer is correctly wired to the load. Check the selected time setting or if the timer is in HOLD mode.
• ഇടവിട്ടുള്ള പ്രവർത്തനം: Inspect wiring for loose connections. Ensure the timer is not overloaded beyond its specified electrical ratings.

If issues persist after following these steps, contact a qualified electrician or Intermatic customer support for assistance.

സ്പെസിഫിക്കേഷനുകൾ

വാറൻ്റി വിവരങ്ങൾ

This Intermatic product is covered by a 1 വർഷത്തെ വാറൻ്റി. This warranty covers replacement of the unit but does not include labor costs. For detailed warranty terms and conditions, please refer to the official Intermatic warranty statement or contact customer support.

ഉപഭോക്തൃ പിന്തുണ

For technical assistance, troubleshooting, or warranty claims, please contact Intermatic customer support. You can find contact information on the official Intermatic webസൈറ്റ് അല്ലെങ്കിൽ ഉൽപ്പന്ന പാക്കേജിംഗ് പരാമർശിച്ചുകൊണ്ട്.