SkyTech SKY-5301 Fireplace Remote and Thermostat Instruction Manual

1. ആമുഖം

The SkyTech SKY-5301 remote control system provides a safe, reliable, and user-friendly method for operating gas heating appliances. This system allows for both thermostatic and manual control directly from the handheld transmitter. It operates using radio frequencies (RF) within a 20-foot range, utilizing non-directional signals. The system is pre-programmed with one of 1,048,567 security codes at the factory. For initial use, the remote receiver's code must be matched to the transmitter's code.

2 സുരക്ഷാ വിവരങ്ങൾ

• ഇൻസ്റ്റാളേഷനും പ്രവർത്തനത്തിനും മുമ്പ് എല്ലാ നിർദ്ദേശങ്ങളും ശ്രദ്ധാപൂർവ്വം വായിക്കുക.
• This system is designed for use with millivolt gas valves only. The receiver acts as a dry contact switch and will not output any voltage.
• Ensure all wiring is performed by a qualified technician and complies with local codes.
• Do not expose the transmitter or receiver to water or extreme temperatures.
• Replace batteries promptly when the low battery indicator appears to ensure proper operation.
• കുട്ടികൾക്ക് ലഭ്യമാകാതെ സൂക്ഷിക്കുക.

3. പാക്കേജ് ഉള്ളടക്കം

നിങ്ങളുടെ പാക്കേജിൽ എല്ലാ ഘടകങ്ങളും ഉണ്ടെന്ന് ഉറപ്പാക്കുക:

• Handheld Transmitter (with LCD display)
• Receiver Box (wall plate mounted)
• Wall Plate (for receiver mounting)
• ഇൻസ്റ്റലേഷൻ നിർദ്ദേശങ്ങൾ
• Batteries (4 AA batteries for transmitter and receiver)

4. ഘടകങ്ങൾ കഴിഞ്ഞുview

The SkyTech SKY-5301 system consists of a handheld transmitter and a wall-mounted receiver unit. Understanding each component is essential for proper setup and operation.

ചിത്രം 1: കഴിഞ്ഞുview of the SkyTech SKY-5301 system, showing the handheld transmitter with its backlit LCD screen displaying temperature and time, and the wall-mounted receiver with its ON/REMOTE/OFF slider switch and LEARN button.

4.1. Handheld Transmitter

• LCD ഡിസ്പ്ലേ: Shows room temperature, set temperature, 24-hour clock, and a 9-hour countdown timer. Features a backlight for visibility.
• ബട്ടണുകൾ: Three buttons (Up, Mode, Down) for navigation and setting adjustments.
• പ്രവർത്തനക്ഷമത: Allows for manual or thermostatic control of the fireplace.

4.2. Wall-Mounted Receiver

• സ്ലൈഡർ സ്വിച്ച്: Features ON, REMOTE, and OFF positions for direct control or remote operation.
• പഠിക്കുക ബട്ടൺ: Used to synchronize the receiver with the transmitter.
• ശക്തി: Battery-powered for reliable operation.
• അനുയോജ്യത: Designed exclusively for millivolt gas valves, acting as a dry contact switch. It does not output voltage.

5. സജ്ജീകരണം

5.1. ബാറ്ററി ഇൻസ്റ്റാളേഷൻ

Install the included AA batteries into both the transmitter and the receiver unit.

1. ട്രാൻസ്മിറ്റർ: Open the battery compartment on the back of the handheld transmitter. Insert the batteries, observing the correct polarity (+/-). Close the compartment.
2. റിസീവർ: Remove the wall plate cover. Open the battery compartment on the receiver unit. Insert the batteries, observing the correct polarity (+/-). Close the compartment.

5.2. Receiver Wiring

The receiver unit must be wired to your fireplace's millivolt gas valve. This process typically involves connecting two wires from the receiver to the appropriate terminals on the gas valve. Ensure the fireplace's gas supply is turned OFF before proceeding with any wiring.

1. Locate the millivolt gas valve on your fireplace.
2. Identify the two terminals designated for remote control or thermostat connection. These are typically labeled TH and TH/TP or similar.
3. Connect the two wires from the receiver unit to these terminals. The polarity of these wires usually does not matter for a dry contact switch.
4. കണക്ഷനുകൾ സുരക്ഷിതമാക്കുക.

5.3. റിസീവർ മൌണ്ട് ചെയ്യുന്നു

After wiring, mount the receiver unit to the wall using the provided wall plate and hardware. Ensure it is in a location where it can receive signals from the transmitter, ideally within 20 feet and not obstructed by large metal objects.

5.4. Pairing the Transmitter and Receiver (Learning Function)

The transmitter and receiver must be paired to communicate. This process is called the "learning function."

1. Ensure batteries are installed in both units.
2. On the receiver unit, slide the ON/REMOTE/OFF switch to the റിമോട്ട് സ്ഥാനം.
3. അമർത്തിപ്പിടിക്കുക പഠിക്കുക button on the receiver for approximately 3 seconds until you hear a short beep.
4. Within 20 seconds of the beep, press any button on the handheld transmitter.
5. The receiver will emit a series of beeps, confirming that the transmitter and receiver are now paired.
6. Test the connection by pressing the "Up" or "Down" button on the transmitter to see if the fireplace responds.

6. ഓപ്പറേഷൻ

6.1. Transmitter Display and Controls

The backlit LCD on the transmitter provides essential information and allows for easy control.

• വിവരങ്ങൾ പ്രദർശിപ്പിക്കുക:
  • നിലവിലെ മുറിയിലെ താപനില
  • താപനില സജ്ജമാക്കുക
  • 24-മണിക്കൂർ ക്ലോക്ക്
  • 9-മണിക്കൂർ കൗണ്ട്‌ഡൗൺ ടൈമർ
  • ബാറ്ററി ലെവൽ ഇൻഡിക്കേറ്റർ
• ബട്ടണുകൾ:
  • മുകളിലേക്ക് (▲): Increases set temperature, adjusts time/timer up.
  • മോഡ്/സെറ്റ്: Cycles through operating modes, enters setting menus.
  • താഴേക്ക് (▼): Decreases set temperature, adjusts time/timer down.

6.2 ഓപ്പറേറ്റിംഗ് മോഡുകൾ

The system supports two primary operating modes:

• മാനുവൽ മോഡ്: The fireplace turns ON or OFF directly when commanded by the transmitter, regardless of temperature.
• തെർമോസ്റ്റാറ്റിക് മോഡ്: The fireplace will turn ON or OFF automatically to maintain the set temperature.

6.3. താപനില ക്രമീകരണം

1. അമർത്തുക മോഡ്/സെറ്റ് button until the display shows the desired operating mode (e.g., "THERMO").
2. ഉപയോഗിക്കുക യുപി (▲) or ഡൗൺ (▼) buttons to adjust the set temperature to your desired level. The display will show the set temperature.
3. The system will automatically maintain this temperature in thermostatic mode.

6.4. ടൈമർ സജ്ജീകരിക്കുന്നു

The 9-hour countdown timer can be used to automatically turn off the fireplace after a set duration.

1. അമർത്തുക മോഡ്/സെറ്റ് button until the display shows "TIMER".
2. ഉപയോഗിക്കുക യുപി (▲) or ഡൗൺ (▼) buttons to set the desired countdown duration (up to 9 hours).
3. Once set, the timer will begin counting down. The fireplace will turn off when the timer reaches zero.

7. പരിപാലനം

7.1. ബാറ്ററി മാറ്റിസ്ഥാപിക്കൽ

When the low battery indicator appears on the transmitter's LCD, or if the system becomes unresponsive, replace the batteries in both the transmitter and receiver with fresh AA batteries. Always replace all batteries at the same time.

7.2. വൃത്തിയാക്കൽ

Wipe the transmitter and receiver surfaces with a soft, dry cloth. Do not use abrasive cleaners or immerse the units in water.

8. പ്രശ്‌നപരിഹാരം

9 സ്പെസിഫിക്കേഷനുകൾ

10. വാറൻ്റിയും പിന്തുണയും

For warranty information or technical support, please refer to the contact details provided with your product packaging or visit the official SkyTech webസൈറ്റ്. വാറൻ്റി ക്ലെയിമുകൾക്കായി നിങ്ങളുടെ വാങ്ങൽ രസീത് സൂക്ഷിക്കുക.