1. ആമുഖം
This instruction manual provides essential information for the proper installation, operation, and maintenance of your Nordyne 903110A Furnace Igniter Kit with Plug. Please read this manual thoroughly before attempting any installation or service to ensure safe and efficient use of the product.
സുരക്ഷാ മുന്നറിയിപ്പ്: The igniter element is extremely fragile. Handle with care. Do not touch the igniter element directly with bare hands as oils can shorten its lifespan. Always disconnect power to the furnace before installation or maintenance.
2. ഉൽപ്പന്നം കഴിഞ്ഞുview
The Nordyne 903110A Igniter Kit is a replacement igniter designed for various furnace models, including those starting with M1M from Nordyne, Miller, Intertherm, and Broan. It replaces older style spiral igniters and is compatible with part numbers 632313, 632313C, 903110, 903110A, FC047, and F-1022-21.
- ഉൽപ്പന്ന തരം: Auto Part (Furnace Igniter)
- മെറ്റീരിയൽ: Heat-Resistant Silicon Nitride for durability and anti-aging properties.
- ബ്രാക്കറ്റ്: Aluminum Alloy bracket for higher heat resistance and improved power connection.
- പ്ലഗ്: Highly engineered plug, tested to OEM standards.
Figure 2.1: The Nordyne 903110A Furnace Igniter Kit, showing the igniter element, wiring, and connector.
ചിത്രം 2.2: ഒരു അടുത്ത് view of the igniter element and its mounting bracket.
Figure 2.3: The igniter kit showing the full length of the igniter and its attached wiring.
ഉൽപ്പന്ന വീഡിയോ കഴിഞ്ഞുview
വീഡിയോ 2.1: ഒരു ഓവർview of the 903110A Furnace Hot Surface Ignitor, detailing its features and applications. This video is provided by the seller to demonstrate the product.
3 അനുയോജ്യത
This igniter kit is designed as a direct replacement for the following part numbers and is compatible with furnace models from various brands:
- പാർട്ട് നമ്പറുകൾ മാറ്റിസ്ഥാപിക്കുന്നു: 632313, 632313C, 903110, 903110A, FC047, F-1022-21, 632666.
- അനുയോജ്യമായ ബ്രാൻഡുകൾ: Nordyne, Miller, Intertherm, Broan, Frigidaire, Maytag, Gibson.
- Specifically designed for furnace models starting with M1M.
4 സുരക്ഷാ വിവരങ്ങൾ
Adhering to safety precautions is crucial when working with furnace components. Failure to follow these instructions could result in property damage, personal injury, or death.
- പവർ വിച്ഛേദിക്കുക: Always turn off the electrical power to the furnace at the main service panel before beginning any installation, maintenance, or troubleshooting.
- ഗ്യാസ് വിതരണം: Ensure the gas supply to the furnace is turned off before working on the igniter.
- ദുർബലമായ ഘടകം: The igniter element is ceramic and very fragile. Avoid dropping or striking it.
- മലിനീകരണം ഒഴിവാക്കുക: Do not touch the igniter element with bare hands. Oils from your skin can create hot spots and shorten the igniter's lifespan. Use clean gloves or handle by the ceramic base.
- പ്രൊഫഷണൽ ഇൻസ്റ്റാളേഷൻ: If you are not comfortable performing this installation, it is recommended to contact a qualified HVAC technician.
- ശരിയായ ഉപകരണങ്ങൾ: Use appropriate tools for the job to prevent damage to the igniter or furnace components.
5. സജ്ജീകരണവും ഇൻസ്റ്റാളേഷനും
Follow these steps carefully to replace your furnace igniter. Refer to your furnace's specific service manual for detailed instructions if available.
- ഇൻസ്റ്റാളേഷനായി തയ്യാറെടുക്കുക:
- Turn off all electrical power to the furnace at the main breaker.
- ചൂളയിലേക്കുള്ള ഗ്യാസ് വിതരണം ഓഫ് ചെയ്യുക.
- Locate the igniter within your furnace. It is typically found near the burners.
- Remove Old Igniter:
- Carefully disconnect the electrical connector from the old igniter.
- Unscrew any mounting screws or clips holding the old igniter in place.
- Gently remove the old igniter, being careful not to damage other components.
- പുതിയ ഇഗ്നിറ്റർ ഇൻസ്റ്റാൾ ചെയ്യുക:
- Handle the new igniter by its ceramic base or with clean gloves to avoid touching the silicon nitride element.
- Position the new igniter in the same location and orientation as the old one.
- Secure the igniter with the mounting screws or clips. Ensure it is firmly in place but do not overtighten.
- Connect the electrical plug of the new igniter to the furnace wiring harness. Ensure a secure connection.
- പവർ പുനഃസ്ഥാപിക്കുകയും പരിശോധിക്കുകയും ചെയ്യുക:
- Turn the gas supply back on.
- Restore electrical power to the furnace at the main breaker.
- Initiate a heating cycle on your thermostat to test the new igniter. Observe for proper ignition.
- If the furnace does not ignite or operates abnormally, refer to the Troubleshooting section.
6. പ്രവർത്തന നിർദ്ദേശങ്ങൾ
The igniter operates automatically as part of your furnace's ignition sequence. When the thermostat calls for heat, the igniter will glow hot to ignite the gas burners. No direct user interaction is required for the igniter's operation once installed correctly.
- Ensure your thermostat is set to "Heat" mode and the desired temperature is above the current room temperature.
- The furnace control board will initiate the igniter, which will heat up to a high temperature.
- Once sufficiently hot, the gas valve will open, and the gas will ignite from the hot surface of the igniter.
- The igniter will then turn off as the flame sensor confirms successful ignition.
7. പരിപാലനം
Regular maintenance helps ensure the longevity and efficient operation of your furnace and its components, including the igniter.
- വാർഷിക പരിശോധന: It is recommended to have your furnace inspected annually by a qualified HVAC technician. They can check the igniter for signs of wear or damage.
- വൃത്തിയാക്കൽ: If the igniter appears dirty or coated with residue, it can be gently cleaned with a soft brush. Ensure the furnace is powered off and cooled down before attempting any cleaning. Avoid using abrasive materials or chemicals.
- ദൃശ്യ പരിശോധന: Periodically, visually inspect the igniter for cracks, discoloration, or other signs of degradation. A healthy igniter should glow brightly and consistently.
- ശാരീരിക സമ്പർക്കം ഒഴിവാക്കുക: As mentioned, avoid touching the igniter element directly to prevent contamination.
8. പ്രശ്നപരിഹാരം
If your furnace is experiencing issues related to ignition, consult the table below for common problems and potential solutions. Always ensure power and gas are off before inspecting components.
| പ്രശ്നം | സാധ്യമായ കാരണം | പരിഹാരം |
|---|---|---|
| Igniter does not glow. | No power to furnace, faulty igniter, loose wiring connection, faulty control board. | Check furnace breaker. Verify wiring connections. Test igniter for continuity (if comfortable and knowledgeable). Replace igniter if faulty. Consult HVAC technician for control board issues. |
| Igniter glows but gas does not ignite. | No gas supply, faulty gas valve, dirty burners, faulty flame sensor. | Ensure gas supply is on. Check for gas leaks. Clean burners. Inspect flame sensor for damage or dirt. Consult HVAC technician for gas valve or flame sensor replacement. |
| Igniter glows weakly or intermittently. | Aging igniter, contaminated igniter surface, low voltage. | Replace igniter. Gently clean igniter surface (see Maintenance). Check furnace wiring for proper voltage. |
| ചൂള വേഗത്തിൽ ഓണും ഓഫും ആക്കുന്നു (ഷോർട്ട് സൈക്ലിംഗ്). | Could be related to ignition issues, but often other furnace problems (e.g., airflow, thermostat). | Ensure igniter is functioning correctly. Check air filter. Consult HVAC technician for diagnosis. |
If you are unable to resolve the issue after following these steps, it is recommended to contact a qualified HVAC professional for further assistance.
9 സ്പെസിഫിക്കേഷനുകൾ
| ഫീച്ചർ | വിശദാംശങ്ങൾ |
|---|---|
| ബ്രാൻഡ് | നോർഡിൻ |
| മോഡൽ നമ്പർ | I903110 (Replaces 903110A) |
| ഉൽപ്പന്ന തരം | Furnace Igniter Kit |
| Igniter Material | Heat-Resistant Silicon Nitride |
| ബ്രാക്കറ്റ് മെറ്റീരിയൽ | അലുമിനിയം അലോയ് |
| ഇൻസ്റ്റലേഷൻ തരം | ബോൾട്ട്-ഓൺ |
| കണക്റ്റർ ലിംഗഭേദം | പുരുഷൻ |
| ഇനത്തിൻ്റെ ഭാരം | 0.1 കിലോഗ്രാം (ഏകദേശം 3.52 ഔൺസ്) |
| പാക്കേജ് അളവുകൾ | ഏകദേശം 5.39 x 3.15 x 2.91 ഇഞ്ച് |
| യു.പി.സി | 663132151295 |
10. വാറൻ്റിയും പിന്തുണയും
For specific warranty information regarding your Nordyne 903110A Furnace Igniter Kit, please refer to the documentation provided with your purchase or contact Nordyne customer support directly. Keep your proof of purchase for warranty claims.
If you require technical assistance or have questions not covered in this manual, please contact a qualified HVAC professional or the manufacturer's customer service department.
