Zippo 45016 Digital Quartz Watch

ആമുഖം

Thank you for choosing the Zippo 45016 Digital Quartz Watch. This manual provides detailed instructions to help you understand and operate your new watch effectively. Please read this manual thoroughly before use and keep it for future reference.

സുരക്ഷാ വിവരങ്ങൾ

• Do not attempt to open the watch case or replace the battery yourself, as this may void the warranty and damage the watch.
• വാച്ചിൽ തീവ്രമായ താപനില, ദീർഘനേരം നേരിട്ടുള്ള സൂര്യപ്രകാശം, അല്ലെങ്കിൽ ശക്തമായ കാന്തികക്ഷേത്രങ്ങൾ എന്നിവ ഏൽക്കുന്നത് ഒഴിവാക്കുക.
• മൃദുവായതും ഉണങ്ങിയതുമായ തുണി ഉപയോഗിച്ച് വാച്ച് വൃത്തിയാക്കുക. കെമിക്കൽ ക്ലീനറുകൾ ഉപയോഗിക്കരുത്.
• While the watch is designed for daily wear, avoid direct impact or dropping it.

സജ്ജമാക്കുക

Initial Power-On and Time Setting

Your Zippo 45016 watch comes with a pre-installed battery. Upon first use, you may need to set the current time and date.

1. Locate the mode button (usually on the bottom left) and the adjustment buttons (usually on the right side).
2. Press the mode button repeatedly until the time setting mode is displayed. Digits for hours or minutes will typically flash.
3. Use the adjustment buttons (e.g., 'Start/Stop' or 'Reset') to increase or decrease the flashing value.
4. Press the mode button again to move to the next setting (minutes, year, month, day).
5. Once all settings are correct, press the mode button one last time to exit the setting mode.

Image: Zippo 45016 Digital Quartz Watch. This image shows the watch face and strap, illustrating its general appearance and button placement for setup and operation.

പ്രവർത്തന നിർദ്ദേശങ്ങൾ

അടിസ്ഥാന സമയ പ്രദർശനം

In the default mode, the watch displays the current time (hours, minutes, seconds) and often the day of the week and date.

ലൈറ്റ് ഫംഗ്ഷൻ

To illuminate the display in low-light conditions:

• Press the 'Light' button (typically located on the top left or top right of the watch).
• The backlight will activate for a few seconds.

Lap Timer (Stopwatch) Function

The lap timer allows you to measure elapsed time.

1. Press the 'Mode' button until the stopwatch display appears (usually indicated by 'STW' or a stopwatch icon).
2. Press the 'Start/Stop' button (often on the top right) to begin timing.
3. To record a lap time without stopping the main timer, press the 'Lap' or 'Reset' button. The lap time will display briefly.
4. Press 'Start/Stop' again to pause the timer.
5. Press 'Reset' (often on the bottom right) while the timer is paused to clear the stopwatch to zero.

മെയിൻ്റനൻസ്

നിങ്ങളുടെ വാച്ച് വൃത്തിയാക്കൽ

നിങ്ങളുടെ വാച്ചിന്റെ രൂപം നിലനിർത്താൻ:

• Wipe the watch case and strap with a soft, slightly damp തുണി.
• For stubborn dirt, use a mild soap solution, then wipe clean with a damp തുണി നന്നായി ഉണക്കുക.
• Avoid using abrasive cleaners or solvents, as these can damage the watch's finish.

ബാറ്ററി മാറ്റിസ്ഥാപിക്കൽ

The Zippo 45016 uses a product-specific battery. When the display becomes dim or the watch stops functioning, the battery may need replacement. It is recommended to have the battery replaced by a qualified watch technician to ensure proper sealing and functionality.

ട്രബിൾഷൂട്ടിംഗ്

സ്പെസിഫിക്കേഷനുകൾ

• മോഡൽ നമ്പർ: 45016
• ബ്രാൻഡ്: സിപ്പോ
• പ്രസ്ഥാനം: ഡിജിറ്റൽ ക്വാർട്സ്
• ബാറ്ററി: 1 product-specific battery (included)
• ഉൽപ്പന്ന അളവുകൾ: 25.4 x 4.9 x 0.64 സെ.മീ
• ഭാരം: 54.43 ഗ്രാം
• ASIN: B004WMEY9K

വാറൻ്റിയും പിന്തുണയും

For warranty information, please refer to the warranty card included with your purchase or visit the official Zippo website. If you require technical assistance or have questions not covered in this manual, please contact Zippo customer support through their official channels.