ആമുഖം
The Puig 4322N Rear Stand is designed to provide stable support for motorcycles with conventional swingarms. Constructed from high-resistance steel with a black epoxy paint finish, this stand ensures durability and corrosion protection. It is ideal for various tasks including maintenance, cleaning, lubrication, part replacement, and secure long-term parking, helping to extend the vehicle's lifespan and facilitate care.
സുരക്ഷാ വിവരങ്ങൾ
- Always ensure the motorcycle is on a flat, stable, and non-slip surface before using the stand.
- Verify that the stand is correctly positioned under the swingarm spools or contact points before lifting.
- Never leave the motorcycle unattended while it is on the stand, especially during initial setup.
- Do not exceed the weight capacity of the stand. While not explicitly stated, exercise caution with heavy motorcycles.
- Keep hands and feet clear of moving parts during lifting and lowering operations.
- Regularly inspect the stand for any signs of damage, wear, or corrosion. Do not use a damaged stand.
- കയ്യുറകളും സുരക്ഷാ ഗ്ലാസുകളും പോലുള്ള ഉചിതമായ വ്യക്തിഗത സംരക്ഷണ ഉപകരണങ്ങൾ (പിപിഇ) ഉപയോഗിക്കുക.
പാക്കേജ് ഉള്ളടക്കം
പാക്കേജിൽ ഉൾപ്പെടുന്നു:
- One Puig 4322N adjustable steel motorcycle rear stand.
- Necessary hardware for assembly (if applicable, typically pre-assembled or minimal assembly).
സജ്ജീകരണവും അസംബ്ലിയും
The Puig 4322N rear stand is designed for straightforward assembly. Most units come partially assembled, requiring minimal final setup.
- ഘടകങ്ങൾ അൺപാക്ക് ചെയ്യുക: പാക്കേജിംഗിൽ നിന്ന് എല്ലാ ഭാഗങ്ങളും ശ്രദ്ധാപൂർവ്വം നീക്കം ചെയ്യുക. എല്ലാ ഘടകങ്ങളും ഉണ്ടെന്നും കേടുപാടുകൾ സംഭവിച്ചിട്ടില്ലെന്നും പരിശോധിക്കുക.
- പ്രധാന ഫ്രെയിം കൂട്ടിച്ചേർക്കുക: If the main frame is not pre-assembled, connect the two main stand arms using the provided fasteners. Ensure all bolts are tightened securely.
- Attach Swingarm Supports: Install the swingarm support pads or spools onto the stand arms. These are typically adjustable to accommodate different swingarm widths.
- വീതി ക്രമീകരിക്കുക: Place the stand behind your motorcycle. Adjust the width of the swingarm supports to match the width of your motorcycle's swingarm or spools. Ensure a snug fit without being too tight.
- അന്തിമ പരിശോധന: Before use, double-check all connections and adjustments to ensure the stand is stable and ready.
പ്രവർത്തന നിർദ്ദേശങ്ങൾ
Follow these steps to safely lift and lower your motorcycle using the Puig 4322N rear stand.
- മോട്ടോർസൈക്കിൾ തയ്യാറാക്കുക: Ensure the motorcycle is in neutral gear and on its side stand.
- സ്റ്റാൻഡ് സ്ഥാനം: Place the rear stand behind the motorcycle. Align the stand's support pads or spools with the motorcycle's swingarm or spools. Ensure the stand is centered and the contact points are secure.
- Lift Motorcycle: While holding the motorcycle upright with one hand on the handlebar or rear grab handle, firmly push down on the stand's lever arm with your foot or other hand. The motorcycle's rear wheel should lift smoothly off the ground. Ensure the stand's feet are flat on the ground and stable.
- സ്ഥിരത പരിശോധിക്കുക: Once lifted, gently rock the motorcycle to confirm it is stable on the stand.
- Lower Motorcycle: To lower, firmly hold the motorcycle upright. Place one foot on the stand's lever arm and carefully lift the stand's handle, allowing the motorcycle to gently descend onto its wheels and side stand.
മെയിൻ്റനൻസ്
Proper maintenance ensures the longevity and safe operation of your Puig 4322N rear stand.
- പതിവ് വൃത്തിയാക്കൽ: പരസ്യം ഉപയോഗിച്ച് സ്റ്റാൻഡ് തുടയ്ക്കുകamp cloth to remove dirt, grease, and debris.
- കേടുപാടുകൾക്കായി പരിശോധിക്കുക: Periodically check the steel frame for dents, bends, cracks, or signs of corrosion. Inspect the epoxy paint for chips that could expose the metal to rust.
- ഫാസ്റ്റനറുകൾ പരിശോധിക്കുക: Ensure all bolts, nuts, and pivot points are tight. Re-tighten if necessary.
- ചലിക്കുന്ന ഭാഗങ്ങൾ ലൂബ്രിക്കേറ്റ് ചെയ്യുക: If the stand has pivot points or adjustable mechanisms, apply a small amount of appropriate lubricant to ensure smooth operation.
- ശരിയായി സംഭരിക്കുക: When not in use, store the stand in a dry environment to prevent rust and damage.
ട്രബിൾഷൂട്ടിംഗ്
If you encounter issues while using your rear stand, consider the following:
- Motorcycle feels unstable:
- Ensure the stand is on a perfectly flat and level surface.
- Verify that the swingarm supports are correctly adjusted to the motorcycle's width and are making full contact with the swingarm or spools.
- Confirm all fasteners on the stand are securely tightened.
- Difficulty lifting the motorcycle:
- Ensure the stand's lever arm is fully depressed.
- Check that the motorcycle's weight is within a manageable range for a single person to lift with the stand.
- Verify that the stand's wheels are rolling freely.
- Stand appears damaged:
- Do not use the stand if any structural components are bent, cracked, or severely corroded. Contact Puig support for assistance.
സ്പെസിഫിക്കേഷനുകൾ
| ബ്രാൻഡ്: | പ്യൂഗ് |
| മോഡൽ നമ്പർ: | 4322N |
| നിറം: | കറുപ്പ് |
| മെറ്റീരിയൽ: | ഉരുക്ക് |
| ഉൽപ്പന്ന അളവുകൾ: | 54.7 x 48.1 x 8 സെ.മീ |
| ഉൽപ്പന്ന ഭാരം: | 3 കി.ഗ്രാം |
| പ്രത്യേക സവിശേഷതകൾ: | ക്രമീകരിക്കാവുന്ന |
| ശുപാർശ ചെയ്യുന്ന ഉപയോഗം: | Motorcycle Support |
വാറൻ്റിയും പിന്തുണയും
For warranty information or technical support regarding your Puig 4322N Rear Stand, please refer to the documentation provided with your purchase or visit the official Puig website. Contact their customer service for any inquiries or assistance.
Official Puig Webസൈറ്റ്: www.puig.tv
