ആമുഖം
This manual provides essential information for the proper installation, maintenance, and care of your Chrysler Genuine 5020664AC B-Pillar Molding. Please read this manual thoroughly before beginning installation to ensure correct procedure and optimal performance.
സുരക്ഷാ വിവരങ്ങൾ
Always exercise caution when working with automotive parts. Wear appropriate personal protective equipment (PPE) such as gloves and eye protection. Ensure the vehicle is stable and secure before beginning any work. Keep small parts away from children.
പാക്കേജ് ഉള്ളടക്കം
പാക്കേജ് തുറക്കുമ്പോൾ എല്ലാ ഘടകങ്ങളും ഉണ്ടെന്നും കേടുപാടുകൾ സംഭവിച്ചിട്ടില്ലെന്നും ഉറപ്പാക്കുക.
- 1 x Chrysler Genuine 5020664AC B-Pillar Molding
ചിത്രം 1: മുൻഭാഗം view of the B-Pillar Molding, showing its overall shape and finish.
ഇൻസ്റ്റലേഷൻ നിർദ്ദേശങ്ങൾ
This B-Pillar Molding is designed for direct replacement or installation on the vehicle's B-pillar surface. Proper surface preparation is crucial for secure adhesion.
- ഉപരിതലം തയ്യാറാക്കുക: Thoroughly clean the B-pillar surface where the molding will be applied. Use an automotive-grade degreaser or alcohol wipe to remove any dirt, wax, or grease. Allow the surface to dry completely.
- ടെസ്റ്റ് ഫിറ്റ്: Before removing the adhesive backing, carefully position the molding on the B-pillar to ensure it aligns correctly. Note the exact placement.
- Apply Adhesive (Optional, Recommended): For enhanced adhesion, a thin layer of automotive-grade adhesive (e.g., strong automotive adhesive) can be applied to the back of the molding, avoiding the pre-applied adhesive strips. This step is optional but recommended for a more solid bond.
- പശ പിൻഭാഗം നീക്കം ചെയ്യുക: Carefully peel off the protective film from the adhesive strips on the back of the molding. It is critical not to remove the adhesive tape until the piece is ready for final installation.
- Install the Molding: Align the molding with the prepared B-pillar surface and firmly press it into place. Apply even pressure along the entire length of the molding to ensure full contact with the adhesive. Hold pressure for several minutes.
- ക്യൂറിംഗ് സമയം: Allow the adhesive to cure for at least 24 hours before exposing the vehicle to extreme weather conditions or car washes. Refer to the adhesive manufacturer's instructions if an additional adhesive was used.
ചിത്രം 2: പിൻഭാഗം view of the B-Pillar Molding, highlighting the pre-applied adhesive strips for installation.
മെയിൻ്റനൻസ്
The B-Pillar Molding requires minimal maintenance. Regularly clean the surface with standard automotive cleaning products. Avoid abrasive cleaners or harsh chemicals that could damage the finish or adhesive bond.
ട്രബിൾഷൂട്ടിംഗ്
- Molding not adhering properly: Ensure the surface was thoroughly cleaned and dry before installation. Temperature can affect adhesive performance; install in moderate temperatures. Re-apply with a stronger automotive adhesive if necessary.
- Molding appears misaligned: This typically occurs during initial placement. If the adhesive has not fully cured, it may be possible to carefully reposition. If fully cured, removal may damage the molding or vehicle surface.
സ്പെസിഫിക്കേഷനുകൾ
| ആട്രിബ്യൂട്ട് | വിശദാംശങ്ങൾ |
|---|---|
| ഉൽപ്പന്ന തരം | Auto Part (B-Pillar Molding) |
| ബ്രാൻഡ് | ക്രിസ്ലർ |
| മോഡൽ നമ്പർ | 5020664എസി |
| നിർമ്മാതാവിൻ്റെ ഭാഗം നമ്പർ | 5020664എസി |
| ഇനത്തിൻ്റെ ഭാരം | 7.2 ഔൺസ് (0.44974301448 പൗണ്ട്) |
| പാക്കേജ് അളവുകൾ | 25.98 x 10 x 0.2 ഇഞ്ച് |
| ഉപരിതല ശുപാർശ | സ്തംഭം |
വാറൻ്റിയും പിന്തുണയും
For warranty information or technical support regarding your Chrysler Genuine 5020664AC B-Pillar Molding, please contact Chrysler customer service or refer to the official Chrysler webസൈറ്റ്. വാങ്ങിയതിന്റെ തെളിവായി നിങ്ങളുടെ വാങ്ങൽ രസീത് സൂക്ഷിക്കുക.
Visit the official Chrysler store for more information: Chrysler Store
