1. ആമുഖം
This instruction manual provides essential information for the proper handling, installation, and maintenance of the Genuine Acura 45022-S0K-A11 Front Brake Pad Set. These brake pads are designed to meet the original equipment manufacturer (OEM) specifications for your Acura vehicle, ensuring optimal braking performance and safety. Please read this manual thoroughly before proceeding with any installation or maintenance.
2 സുരക്ഷാ വിവരങ്ങൾ
Brake system work is critical for vehicle safety. Improper installation can lead to serious injury or death. It is highly recommended that installation be performed by a qualified automotive technician.
- Always wear appropriate personal protective equipment (PPE), including safety glasses, gloves, and closed-toe shoes.
- Ensure the vehicle is securely supported on jack stands on a level surface before beginning any work. Never rely solely on a jack.
- Allow the brake system to cool down completely before handling components.
- Do not use petroleum-based lubricants on brake components, as they can damage rubber parts.
- Dispose of old brake pads and brake fluid according to local environmental regulations.
- നിർദ്ദിഷ്ട ടോർക്ക് സ്പെസിഫിക്കേഷനുകൾക്കും നടപടിക്രമങ്ങൾക്കും നിങ്ങളുടെ വാഹനത്തിന്റെ സർവീസ് മാനുവൽ പരിശോധിക്കുക.
3. പാക്കേജ് ഉള്ളടക്കം
The Genuine Acura 45022-S0K-A11 Front Brake Pad Set typically includes the following components:
- Four (4) Front Brake Pads (two inner, two outer)
- Shims (pre-attached or separate, depending on design)
- Hardware (e.g., clips, pins, if applicable)
Image: Genuine Acura 45022-S0K-A11 Front Brake Pad Set. The image displays four individual brake pads, two with their dark friction material facing up, and two flipped to show the metal backing plates, which include pre-attached shims and small metal clips, indicating a complete set for a vehicle's front axle.
4. ഇൻസ്റ്റലേഷൻ നടപടിക്രമം
This section outlines the general steps for replacing front brake pads. Specific procedures may vary by vehicle model. Always refer to your vehicle's factory service manual for detailed instructions.
- തയ്യാറാക്കൽ: Park the vehicle on a level surface, engage the parking brake, and block the rear wheels. Loosen the front wheel lug nuts.
- ലിഫ്റ്റ് ആൻഡ് സെക്യൂർ: Safely lift the front of the vehicle using a jack and support it securely with jack stands. Remove the front wheels.
- Caliper Removal: Locate the brake caliper. Remove the caliper guide pin bolts. Carefully slide the caliper off the rotor and support it to prevent strain on the brake hose. Do not let the caliper hang by the brake hose.
- Pad Removal: കാലിപ്പർ ബ്രാക്കറ്റിൽ നിന്ന് പഴയ ബ്രേക്ക് പാഡുകൾ നീക്കം ചെയ്യുക. അവയുടെ ഓറിയന്റേഷൻ ശ്രദ്ധിക്കുക.
- വൃത്തിയാക്കി പരിശോധിക്കുക: Clean the caliper bracket and guide pins. Inspect the brake rotor for wear, scoring, or warping. Replace rotors if necessary. Lubricate caliper guide pins with appropriate brake grease.
- Piston Retraction: Use a brake caliper piston compression tool to slowly and evenly push the caliper piston(s) back into the caliper bore. This creates space for the new, thicker pads. Open the brake fluid reservoir cap before retracting pistons.
- New Pad Installation: Install the new Acura brake pads into the caliper bracket, ensuring correct orientation (inner and outer pads). Apply a thin layer of brake lubricant to the backing plates of the pads where they contact the caliper and shims, if not pre-applied.
- Caliper Reinstallation: Carefully slide the caliper back over the new pads and rotor. Reinstall and torque the caliper guide pin bolts to the manufacturer's specifications.
- അവസാന ഘട്ടങ്ങൾ: Reinstall the wheels and torque the lug nuts to specifications. Lower the vehicle. Pump the brake pedal several times until it feels firm before driving. Check the brake fluid level and top off if necessary.
5. പ്രവർത്തന, ബ്രേക്ക്-ഇൻ നടപടിക്രമം
After installing new brake pads, a proper break-in (bedding-in) procedure is crucial for optimal performance and longevity. This process transfers a thin layer of friction material to the rotor surface, ensuring consistent braking and preventing noise.
- വാഹനം മിതമായ വേഗതയിൽ ഓടിക്കുക (ഉദാ: മണിക്കൂറിൽ 30-40 മൈൽ).
- ബ്രേക്കുകൾ മിതമായി മാത്രം ഉപയോഗിക്കുക (ആക്രമണാത്മകമായിട്ടല്ല) ഏകദേശം 10 mph ആയി വേഗത കുറയ്ക്കുക. പൂർണ്ണമായും നിർത്തരുത്.
- Repeat this process approximately 10-15 times, allowing a short cool-down period between each stop.
- Avoid hard braking or prolonged braking (e.g., long downhill descents) for the first 200-300 miles after installation.
During the break-in period, you may notice a slight burning smell or reduced braking effectiveness. This is normal. Braking performance will improve as the pads bed in.
6. പരിപാലനം
Regular inspection of your brake pads is essential for safety and performance.
- പതിവ് പരിശോധന: Inspect brake pads for wear during tire rotations or at least every 10,000-15,000 miles.
- കുറഞ്ഞ കനം: Replace brake pads when the friction material wears down to the minimum recommended thickness (typically 2-3mm, or as indicated by your vehicle's wear indicators).
- ബ്രേക്ക് ഫ്ലൂയിഡ്: Check brake fluid level regularly and ensure it is within the recommended range. Brake fluid should be flushed and replaced according to your vehicle manufacturer's schedule.
- റോട്ടർ അവസ്ഥ: Always inspect brake rotors for excessive wear, deep grooves, or cracks when replacing pads. Rotors should be resurfaced or replaced if they are below minimum thickness or show significant damage.
7. പ്രശ്നപരിഹാരം
If you experience any issues after brake pad installation, consider the following common problems and solutions:
| ലക്ഷണം | സാധ്യമായ കാരണം | പരിഹാരം |
|---|---|---|
| ഞരക്കമോ അലർച്ചയോ ഉള്ള ശബ്ദം | Improper break-in, lack of lubrication on backing plates/shims, worn pads (wear indicator), foreign material. | Perform break-in procedure. Re-lubricate contact points. Inspect pads for wear. Clean brake components. |
| പൊടിക്കുന്ന ശബ്ദം | Severely worn pads (metal-on-metal contact), foreign object lodged in caliper. | Immediately inspect and replace worn pads. Remove foreign objects. Inspect rotors for damage. |
| Pulsating Brake Pedal | വളഞ്ഞ ബ്രേക്ക് റോട്ടറുകൾ. | Inspect and replace or resurface brake rotors. |
| Soft/Spongy Pedal | Air in the brake lines, low brake fluid, faulty master cylinder. | Bleed the brake system. Check brake fluid level. Inspect for leaks. Consult a professional. |
If troubleshooting steps do not resolve the issue, or if you are unsure, consult a certified automotive technician.
8 സ്പെസിഫിക്കേഷനുകൾ
Key specifications for the Genuine Acura 45022-S0K-A11 Front Brake Pad Set:
- ഭാഗം നമ്പർ: 45022-S0K-A11
- ബ്രാൻഡ്: അക്കുറ
- സ്ഥാനം: ഫ്രണ്ട് ആക്സിൽ
- ഇനത്തിൻ്റെ ഭാരം: ഏകദേശം 4.4 പൗണ്ട് (സെറ്റിന്)
- ഉൽപ്പന്ന അളവുകൾ: ഏകദേശം 6.5 x 3.27 x 2.52 ഇഞ്ച് (പാക്കേജിംഗ്)
- സ്പെസിഫിക്കേഷൻ മെറ്റ്: OEM
Note: These specifications are based on typical product information and may vary slightly. Always verify compatibility with your specific vehicle model and year.
9. വാറൻ്റിയും പിന്തുണയും
For information regarding the warranty of Genuine Acura parts, please refer to the warranty documentation provided with your purchase or contact an authorized Acura dealership or parts distributor. They can provide details on coverage, terms, and conditions.
For technical support or further assistance, it is recommended to contact your local authorized Acura service center or a certified automotive professional.
