Eurolite 70064224 ESX-4R Switchpack 4-Channel DMX Controller Instruction Manual

1. ആമുഖം

This manual provides detailed instructions for the safe and efficient operation of your Eurolite 70064224 ESX-4R Switchpack. The ESX-4R is a robust 4-channel DMX switchpack designed for controlling various lighting fixtures and electrical devices in stage and event environments. It features four Type F output sockets, DMX512 input and output, and a maximum total current capacity of 16A.

Please read this manual thoroughly before initial use and keep it for future reference. Adherence to these instructions is crucial for proper function and safety.

2. സുരക്ഷാ നിർദ്ദേശങ്ങൾ

പൊതു സുരക്ഷ:

• This device is intended for professional use only.
• ഉപകരണം ഒരു ഗ്രൗണ്ടഡ് പവർ ഔട്ട്‌ലെറ്റുമായി ബന്ധിപ്പിച്ചിട്ടുണ്ടെന്ന് ഉറപ്പാക്കുക.
• മഴയോ ഈർപ്പമോ ഉപകരണത്തെ തുറന്നുകാട്ടരുത്.
• Disconnect from mains power before cleaning or servicing.
• പവർ കോർഡിനോ പ്ലഗ്ഗിനോ കേടുപാടുകൾ സംഭവിച്ചാൽ ഉപകരണം പ്രവർത്തിപ്പിക്കരുത്.
• എല്ലാ അറ്റകുറ്റപ്പണികളും യോഗ്യതയുള്ള സേവന ഉദ്യോഗസ്ഥർ നടത്തണം.
• അമിതമായി ചൂടാകുന്നത് തടയാൻ യൂണിറ്റിന് ചുറ്റും മതിയായ വായുസഞ്ചാരം ഉറപ്പാക്കുക.

ഇലക്ട്രിക്കൽ സുരക്ഷ:

• The maximum current per channel is 5A. Do not exceed this limit.
• The maximum total current for the unit is 16A.
• The device uses triac switching. Be aware that a small residual voltage may be present on the output even when a channel is switched off. This can cause low-energy devices (e.g., some LED bulbs) to glow faintly or flicker. This is a characteristic of triac-based switching and not a defect.

3. ഉൽപ്പന്ന ഘടകങ്ങളും നിയന്ത്രണങ്ങളും

ചിത്രം 3.1: കോണാകൃതിയിലുള്ളത് view of the Eurolite ESX-4R Switchpack, showing the front panel with controls and the four output sockets.

3.1 ഫ്രണ്ട് പാനൽ

Figure 3.2: Close-up of the ESX-4R Switchpack front panel.

• CH1-CH4 Output Sockets: Four Type F sockets for connecting electrical loads. Each channel can handle up to 5A.
• സർക്യൂട്ട് ബ്രേക്കർ: Provides overload protection for the unit.
• ഡിജിറ്റൽ ഡിസ്പ്ലേ: Shows current DMX address and menu options.
• Control Buttons (ESC, DOWN, UP, ENTER): Used for navigating menus and setting DMX addresses.
• Channel Status LEDs (CH1-CH4): Indicate the on/off status of each channel.

3.2 പിൻ പാനൽ

Figure 3.3: Close-up of the ESX-4R Switchpack rear panel.

• DMX IN (XLR 3-pin): Connects to a DMX controller or the preceding DMX device.
• DMX OUT (XLR 3-pin): Connects to the next DMX device in the chain.
• പവർ ഇൻപുട്ട്: Standard IEC power connector for mains power supply.

4. സജ്ജീകരണവും ഇൻസ്റ്റാളേഷനും

4.1 മൗണ്ടിംഗ്:

• The ESX-4R Switchpack can be placed on a flat surface or mounted in a rack using appropriate mounting hardware (not included).
• Ensure the mounting location is stable and provides adequate ventilation.

4.2 പവർ കണക്ഷൻ:

1. Connect the supplied power cable to the power input on the rear panel of the ESX-4R.
2. Plug the other end of the power cable into a suitable grounded mains power outlet (230V AC, 50Hz).
3. Ensure the circuit breaker on the front panel is in the "ON" position.

4.3 DMX Connection:

1. Connect a DMX cable from your DMX controller's output to the DMX IN (3-pin XLR) connector on the rear panel of the ESX-4R.
2. If chaining multiple DMX devices, connect a DMX cable from the DMX OUT (3-pin XLR) of the ESX-4R to the DMX IN of the next device.
3. For optimal signal integrity, terminate the last device in the DMX chain with a DMX terminator.

4.4 Connecting Loads:

1. Connect your lighting fixtures or other electrical devices to the CH1-CH4 output sockets on the front panel.
2. Ensure that the total current draw for each channel does not exceed 5A and the total current for the entire unit does not exceed 16A.

5. ഓപ്പറേഷൻ

The ESX-4R Switchpack operates by receiving DMX512 signals from a DMX controller. Each of the four channels corresponds to a DMX channel, allowing you to switch connected devices on or off.

5.1 Setting the DMX Address

The DMX address determines the starting channel for the ESX-4R on your DMX universe. The ESX-4R requires 4 DMX channels (one for each output). If you set the starting address to 1, then Channel 1 will respond to DMX channel 1, Channel 2 to DMX channel 2, and so on.

1. അമർത്തുക ഇഎസ്സി button to enter the main menu if not already there.
2. ഉപയോഗിക്കുക UP or താഴേക്ക് buttons to navigate to the "ADDR" (Address) setting.
3. അമർത്തുക പ്രവേശിക്കുക to select the address setting.
4. ഉപയോഗിക്കുക UP or താഴേക്ക് buttons to adjust the DMX starting address (from 1 to 512).
5. അമർത്തുക പ്രവേശിക്കുക to confirm the new address.
6. അമർത്തുക ഇഎസ്സി മെനുവിൽ നിന്ന് പുറത്തുകടക്കാൻ.

5.2 DMX Channel Control

Once the DMX address is set, the ESX-4R will respond to DMX signals:

• Each channel (CH1-CH4) corresponds to a sequential DMX channel starting from your set DMX address.
• When the DMX value for a channel is above a certain threshold (typically 128-255), the corresponding output channel will switch ON.
• When the DMX value is below this threshold (typically 0-127), the corresponding output channel will switch OFF.
• The channel status LEDs on the front panel will indicate the current state (ON/OFF) of each output.

5.3 Important Note on Triac Switching

The ESX-4R utilizes triac-based switching for its outputs. This technology is efficient but has a characteristic where a very small residual voltage may remain on the output even when the channel is commanded OFF. For most traditional incandescent loads, this is imperceptible. However, for highly sensitive or low-power devices such as certain LED lamps or some types of relays, this residual voltage can cause them to:

• Glow faintly when switched off.
• Flicker intermittently when switched off.
• Cause small relays to activate or larger relays to hum.

This behavior is inherent to triac switching and is not a malfunction of the device. If this effect is undesirable, consider using devices designed for zero-cross switching or incorporating a dummy load (e.g., a small incandescent bulb) in parallel with the sensitive load to dissipate the residual voltage.

6. പരിപാലനം

6.1 വൃത്തിയാക്കൽ:

• Disconnect the device from mains power before cleaning.
• യൂണിറ്റിന്റെ പുറംഭാഗം വൃത്തിയാക്കാൻ ഉണങ്ങിയതും മൃദുവായതുമായ തുണി ഉപയോഗിക്കുക.
• ലിക്വിഡ് ക്ലീനറുകളോ ലായകങ്ങളോ ഉപയോഗിക്കരുത്.
• Periodically check ventilation grilles for dust accumulation and clean as necessary to ensure proper airflow.

6.2 Fuse Replacement:

The unit is protected by an internal circuit breaker. If the breaker trips, disconnect all loads and reset it. If it trips repeatedly, consult a qualified technician.

7. പ്രശ്‌നപരിഹാരം

8 സാങ്കേതിക സവിശേഷതകൾ

9. വാറൻ്റി വിവരങ്ങൾ

Eurolite products are manufactured to high-quality standards. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Eurolite webസൈറ്റ്. ഏതെങ്കിലും വാറന്റി ക്ലെയിമുകൾക്ക് നിങ്ങളുടെ വാങ്ങലിന്റെ തെളിവ് സൂക്ഷിക്കുക.

10. ഉപഭോക്തൃ പിന്തുണ

For technical assistance, spare parts, or service inquiries, please contact your local Eurolite dealer or the official Eurolite customer support. Contact information can typically be found on the Eurolite webസൈറ്റ് അല്ലെങ്കിൽ ഉൽപ്പന്ന പാക്കേജിംഗിൽ.

നിർമ്മാതാവ്: Eurolite (Steinigke Showtechnic)