1. ആമുഖം
This manual provides essential information for the safe and effective use of your TRUPER BOAP-1 1 HP Peripheral Water Pump. This pump is designed to generate higher pressure and lift water to greater heights compared to centrifugal pumps, though its flow rate is lower. It is primarily intended for agricultural use with clean water and can be integrated into hydropneumatic systems or irrigation setups.
2 സുരക്ഷാ വിവരങ്ങൾ
Read all safety warnings and instructions carefully before installing or operating the pump. Failure to follow these instructions may result in electric shock, fire, serious injury, or property damage.
- ഇലക്ട്രിക്കൽ സുരക്ഷ: Ensure the pump is connected to a grounded outlet with the correct voltage (127 V) and frequency (60 Hz). Do not operate with damaged cords or plugs. Avoid operating the pump in wet conditions or with wet hands.
- ജല സുരക്ഷ: This pump is designed for clean water only. Do not use it for flammable, corrosive, or abrasive liquids. Ensure all connections are watertight to prevent leaks and electrical hazards.
- ഇൻസ്റ്റലേഷൻ: Install the pump in a covered, dry, and well-ventilated area. The ambient temperature should not exceed 40°C (104°F). Secure the pump horizontally on a flat surface using screws.
- പ്രവർത്തനം: Never run the pump dry. Always ensure the pump is fully primed with clean water before starting. Adhere to the recommended duty cycle of 50 minutes of work for 20 minutes of rest, with a daily maximum of 6 hours.
- പരിപാലനം: ഏതെങ്കിലും അറ്റകുറ്റപ്പണികൾ അല്ലെങ്കിൽ വൃത്തിയാക്കൽ നടത്തുന്നതിന് മുമ്പ് വൈദ്യുതി വിച്ഛേദിക്കുക.
3. ഉൽപ്പന്നം കഴിഞ്ഞുview
The TRUPER BOAP-1 is a robust peripheral water pump designed for demanding applications requiring high pressure. Key features include:
- Generates higher pressure and lifts water to a greater height than centrifugal pumps.
- Suitable for lifting water to high places (above approximately 15 meters).
- Recommended for agricultural use with clean water exclusively.
- Can be used with hydropneumatic systems to increase pressure.
- Ideal for irrigation systems with mini sprinklers or aerial spraying.
ചിത്രം 3.1: ഫ്രണ്ട് view of the TRUPER BOAP-1 water pump, showing the inlet and outlet ports.
ചിത്രം 3.2: Key components of the pump, including the thermal protector, continuous duty capacitor, brass plug, electric motor with external ventilation, and brass impeller for durability and constant pressure.
ചിത്രം 3.3: Illustration of the pump's capabilities, highlighting its ability to generate high pressure, pump water up to 70m, maximum suction depth of 8m, IPX4 protection, and durable brass impeller.
4 സ്പെസിഫിക്കേഷനുകൾ
Detailed technical specifications for the TRUPER BOAP-1 1 HP Peripheral Water Pump are provided below:
| ഫീച്ചർ | സ്പെസിഫിക്കേഷൻ |
|---|---|
| ശക്തി | 1 HP (750 W) |
| പരമാവധി ഉയരം | 70 മീ (229.6 അടി) |
| പരമാവധി ഒഴുക്ക് നിരക്ക് | 50 ലിറ്റർ/മിനിറ്റ് (13.2 ജിപിഎം) |
| പരമാവധി സക്ഷൻ ഡെപ്ത് | 8 മീ (26.2 അടി) |
| ഡ്യൂട്ടി സൈക്കിൾ | 50 minutes work / 20 minutes rest (Daily maximum 6 hours) |
| ഇൻലെറ്റ് / ഔട്ട്ലെറ്റ് വ്യാസം | 1" എൻപിടി |
| വാല്യംtagഇ / ആവൃത്തി | 127V / 60Hz |
| നിലവിലുള്ളത് | 11 എ |
| വേഗത | 3,450 ആർ/മിനിറ്റ് |
| അളവുകൾ (L x W x H) | 13.86" x 7.32" x 8.5" (31 x 14 x 18 സെ.മീ) |
| ഭാരം | 22.9 പൗണ്ട് (10 കി.ഗ്രാം) |
| മെറ്റീരിയൽ | ഉരുക്ക് |
| സംരക്ഷണ റേറ്റിംഗ് | IPX4 |
ചിത്രം 4.1: Visual representation of key performance specifications including maximum flow, maximum height, weight, voltagഇ, ശക്തിയും.
ചിത്രം 4.2: Dimensional drawing of the TRUPER BOAP-1 pump, indicating height, width, and depth.
5. സജ്ജീകരണവും ഇൻസ്റ്റാളേഷനും
പമ്പിന്റെ പ്രകടനത്തിനും ദീർഘായുസ്സിനും ശരിയായ ഇൻസ്റ്റാളേഷൻ നിർണായകമാണ്. ഈ ഘട്ടങ്ങൾ ശ്രദ്ധാപൂർവ്വം പാലിക്കുക:
- സ്ഥാനം: Select a location that is covered, dry, and well-ventilated. Ensure the ambient temperature does not exceed 40°C (104°F).
- മൗണ്ടിംഗ്: Place the pump in a horizontal position on a flat, stable surface. Secure it using appropriate screws through the mounting holes in the base to prevent vibration and movement during operation.
- ജല കണക്ഷനുകൾ: Connect the inlet and outlet pipes to the pump's 1" NPT ports. Ensure all connections are sealed tightly to prevent air leaks on the suction side and water leaks on the discharge side. The maximum suction depth is 8 meters.
- പ്രൈമിംഗ്: Before the first use, and whenever the pump runs dry, completely fill the pump casing with clean water through the priming port. This is essential for peripheral pumps to operate correctly.
- ഇലക്ട്രിക്കൽ കണക്ഷൻ: Connect the pump to a dedicated 127 V / 60 Hz grounded electrical outlet. Ensure the electrical circuit can handle the pump's 11 A current draw.
6. പ്രവർത്തന നിർദ്ദേശങ്ങൾ
Follow these guidelines for optimal operation of your peripheral water pump:
- പ്രാരംഭ ആരംഭം: After installation and priming, ensure all connections are secure. Plug in the pump or turn on the power switch. The pump should start drawing water.
- തുടർച്ചയായ പ്രവർത്തനം: Monitor the pump during initial operation to ensure proper water flow and no unusual noises or vibrations.
- ഡ്യൂട്ടി സൈക്കിൾ: Adhere strictly to the recommended duty cycle: 50 minutes of continuous operation followed by a 20-minute rest period. The maximum daily operation should not exceed 6 hours. This prevents overheating and extends the pump's lifespan.
- ജലത്തിൻ്റെ ഗുണനിലവാരം: This pump is designed exclusively for pumping clean water. Pumping abrasive particles or corrosive liquids will damage the impeller and internal components, voiding the warranty.
- അപേക്ഷകൾ: The pump is suitable for agricultural irrigation (mini sprinklers, aerial spraying), increasing pressure in hydropneumatic systems, and general water supply where high lift is required.
7. പരിപാലനം
Regular maintenance ensures the longevity and efficient operation of your pump. Always disconnect the pump from the power supply before performing any maintenance.
- വൃത്തിയാക്കൽ: Periodically clean the exterior of the pump to prevent dust and debris buildup, which can hinder cooling.
- പരിശോധന: Regularly inspect the power cord for damage and all pipe connections for leaks. Ensure the mounting bolts are tight.
- ശീതകാലം (ബാധകമെങ്കിൽ): In freezing climates, drain all water from the pump and pipes to prevent damage from ice expansion. Store the pump in a warm, dry place if it will not be used for extended periods during cold weather.
- Impeller Check: If flow rate decreases significantly, the impeller may be obstructed or worn. Consult a qualified technician for inspection and replacement if necessary.
8. പ്രശ്നപരിഹാരം
Refer to this section for common issues and their potential solutions. For problems not listed or if solutions do not resolve the issue, contact customer support.
| പ്രശ്നം | സാധ്യമായ കാരണം | പരിഹാരം |
|---|---|---|
| പമ്പ് ആരംഭിക്കുന്നില്ല | No power; tripped circuit breaker; faulty switch. | Check power supply, circuit breaker, and connections. Ensure the switch is ON. |
| പമ്പ് ഓടുന്നു, പക്ഷേ വെള്ളം ഒഴുകുന്നില്ല | Pump not primed; air leak in suction line; clogged inlet/impeller; suction lift too high. | Prime the pump completely. Check all suction line connections for leaks. Clear any blockages. Ensure suction depth is within 8m. |
| കുറഞ്ഞ ജലസമ്മർദ്ദം/പ്രവാഹം | Partial blockage; worn impeller; air in system; discharge head too high. | Check for partial blockages in pipes or impeller. Re-prime the pump. Verify the discharge height is within the pump's maximum (70m). |
| പമ്പ് ശബ്ദമുണ്ടാക്കുന്നു അല്ലെങ്കിൽ അമിതമായി വൈബ്രേറ്റ് ചെയ്യുന്നു | Air in system; loose mounting; foreign object in pump; worn bearings. | Bleed air from the system. Tighten mounting bolts. Disconnect power and inspect for foreign objects (if safe). Contact service for worn bearings. |
| പമ്പ് അമിതമായി ചൂടാകുകയും ഓഫാകുകയും ചെയ്യുന്നു | Exceeding duty cycle; low voltage; running dry; motor overload. | Adhere to the duty cycle. Check voltage supply. Ensure pump is primed and not running dry. Allow pump to cool down. |
9. വാറൻ്റിയും പിന്തുണയും
The TRUPER BOAP-1 1 HP Peripheral Water Pump comes with a 5 വർഷത്തെ വാറൻ്റി നിർമ്മാണ വൈകല്യങ്ങൾക്കെതിരെ. വാറന്റി ക്ലെയിമുകൾക്കായി നിങ്ങളുടെ വാങ്ങിയതിന്റെ തെളിവ് സൂക്ഷിക്കുക.
For technical assistance, spare parts, or warranty service, please contact your authorized Truper dealer or visit the official Truper website for customer support information. Do not attempt to repair the pump yourself, as this may void the warranty and pose safety risks.