ആമുഖം
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Rev-A-Shelf LD-0220-50SC Soft-Close Pivot Hinges. Please read this manual thoroughly before installation and retain it for future reference.
സുരക്ഷാ വിവരങ്ങൾ
- Always wear appropriate safety gear, including eye protection, during installation.
- Ensure all tools are in good working condition.
- ശ്വാസംമുട്ടൽ ഉണ്ടാകുന്നത് തടയാൻ ചെറിയ ഭാഗങ്ങൾ കുട്ടികളിൽ നിന്ന് അകറ്റി നിർത്തുക.
- ഏതെങ്കിലും ഘട്ടത്തെക്കുറിച്ച് നിങ്ങൾക്ക് ഉറപ്പില്ലെങ്കിൽ, യോഗ്യതയുള്ള ഒരു പ്രൊഫഷണലിനെ സമീപിക്കുക.
പാക്കേജ് ഉള്ളടക്കം
- (1) Left Soft-Close Pivot Hinge
- (1) Right Soft-Close Pivot Hinge
- (1) സ്ക്രൂ പായ്ക്ക്
Image: A pair of Rev-A-Shelf LD-0220-50SC Soft-Close Pivot Hinges, showing the spring-loaded mechanism and mounting plates.
സ്പെസിഫിക്കേഷനുകൾ
| ഫീച്ചർ | വിശദാംശങ്ങൾ |
|---|---|
| മോഡൽ നമ്പർ | LD-0220-50SC |
| മെറ്റീരിയൽ | ലോഹം |
| ഫിനിഷ് തരം | പൂർത്തിയാകാത്തത് |
| മൗണ്ടിംഗ് തരം | Face Mount |
| തുറക്കുന്ന ആംഗിൾ | 50-ഡിഗ്രി |
| അളവുകൾ (W x D x H) | 1" (26 mm) W x 2-5/8" (67 mm) D x 3-7/8" (99 mm) H |
| ഉൾപ്പെടുത്തിയ ഘടകങ്ങൾ | (1) Left hinge, (1) right hinge, and screw pack |
സജ്ജീകരണവും ഇൻസ്റ്റാളേഷനും
Proper installation is key to the smooth operation of your soft-close pivot hinges. Follow these steps carefully.
1. Measure Your Cabinet Opening
Before installing, accurately measure the width, height, and depth of your cabinet opening. This ensures compatibility and proper fit for any accessories you plan to use with the tip-out tray.
Video: This video from Rev-A-Shelf provides guidance on how to measure your cabinet opening correctly for various products.
Video: This video explains how to measure and determine if your cabinet hinge is a 1/2" overlay, which is important for proper fit.
2. ഇൻസ്റ്റാളേഷനായി തയ്യാറെടുക്കുക
- Identify the left (L) and right (R) hinges.
- Ensure you have all necessary tools: drill, 3/32 drill bit, pencil, and screwdriver.
3. Mark and Drill Holes on Face Frame
- With the drawer front panel still installed (or aligned to its desired location), use a pencil to lightly mark its perimeter on the front of the face frame.
- Remove the drawer front panel.
- Place one hinge on the appropriate side of the face frame. Align it so the bottom rests on the face frame and the front is flush with the face frame's front.
- Trace the locations of two mounting holes onto the frame. Avoid holes too close to the top or bottom edges for easier drilling.
- മറുവശത്ത് ആവർത്തിക്കുക.
- Drill the marked holes into the face frame using a 3/32 drill bit.
Image: A Rev-A-Shelf Soft-Close Pivot Hinge installed on the inside of a cabinet, with a tip-out tray partially open.
4. Attach Hinges to Face Frame
- Attach the hinges to the face frame using the provided screws.
5. Mark and Drill Holes on Drawer Front Panel
- Place the drawer front panel against the face frame in its desired location, using your previously traced perimeter as a guide.
- From the inside of the cabinet, mark the mounting hole locations from the hinges onto the back of the drawer front panel.
- Remove the panel and carefully drill the mounting holes with a 3/32 bit. Caution: Do not drill all the way through the panel. A drill bit stop collar is recommended.
Image: A Rev-A-Shelf Soft-Close Pivot Hinge installed on the inside of a cabinet, with a tip-out tray open, showing the hinge mechanism.
6. Install Drawer Front Panel
- Attach the drawer front panel to the installed hinges. This can be done from inside the cabinet with the hinges "closed" or from outside with them "open."
- Do not fully tighten screws until all four are in place and the panel is aligned.
ചിത്രം: ഒരു ക്ലോസ്-അപ്പ് view of the Rev-A-Shelf Soft-Close Pivot Hinge mechanism, demonstrating its movement.
7. Test and Adjust
- Test the function of the tip-out tray.
- If needed, slightly loosen the screws and adjust the panel to ensure it closes flush and evenly.
Video: This video demonstrates the installation and operation of the soft-close pivot hinges in a tip-out tray application.
ഓപ്പറേഷൻ
The Rev-A-Shelf LD-0220-50SC hinges feature a 50-degree opening and a soft-close dampener mechanism. This allows the tip-out tray to open smoothly and close quietly, preventing slamming.
- To open: Gently pull the top edge of the tip-out tray forward. The hinges will pivot, allowing access to the interior.
- To close: Gently push the tip-out tray back into its closed position. The soft-close mechanism will engage, ensuring a quiet and controlled closure.
Video: This video illustrates the smooth operation of tip-out tray hinges, showcasing the soft-close feature.
Video: A short demonstration of a tilt-out tray hinge in operation, highlighting its functionality.
മെയിൻ്റനൻസ്
These hinges are designed for durability and require minimal maintenance.
- വൃത്തിയാക്കൽ: മൃദുവായ, ഡി തുണി ഉപയോഗിച്ച് ഹിഞ്ചുകൾ ഇടയ്ക്കിടെ തുടയ്ക്കുക.amp cloth to remove dust and debris. Avoid abrasive cleaners or harsh chemicals that could damage the finish.
- ലൂബ്രിക്കേഷൻ: The hinges are pre-lubricated. If you notice any stiffness over time, a small amount of silicone-based lubricant can be applied to the pivot points.
- പരിശോധന: Regularly check all screws to ensure they are tight. Re-tighten if necessary.
ട്രബിൾഷൂട്ടിംഗ്
Tray Not Closing Softly
- തടസ്സങ്ങൾക്കായി പരിശോധിക്കുക: Ensure nothing is blocking the hinge mechanism or the path of the tray.
- ഇൻസ്റ്റാളേഷൻ പരിശോധിക്കുക: Re-check that the hinges are installed correctly and securely, and that the screws are not overtightened, which could impede movement.
- വിന്യാസം ക്രമീകരിക്കുക: Slight adjustments to the panel's alignment might be needed. Loosen mounting screws slightly, adjust the panel, and re-tighten.
Tray Not Opening Smoothly
- അവശിഷ്ടങ്ങൾക്കായി പരിശോധിക്കുക: Clear any debris that might be caught in the hinge mechanism.
- ലൂബ്രിക്കേഷൻ: Apply a small amount of silicone-based lubricant to the pivot points if the movement feels stiff.
വാറൻ്റി
Rev-A-Shelf LD-0220-50SC Soft-Close Pivot Hinges come with a പരിമിതമായ ആജീവനാന്ത വാറൻ്റി. This warranty covers defects in material and workmanship under normal use. For specific details regarding warranty claims, please refer to the official Rev-A-Shelf webസൈറ്റ് അല്ലെങ്കിൽ ഉപഭോക്തൃ പിന്തുണയുമായി ബന്ധപ്പെടുക.
പിന്തുണ
For further assistance, technical support, or to inquire about replacement parts, please visit the official Rev-A-Shelf webസൈറ്റ് അല്ലെങ്കിൽ അവരുടെ ഉപഭോക്തൃ സേവന വിഭാഗവുമായി ബന്ധപ്പെടുക.
Webസൈറ്റ്: www.rev-a-shelf.com
കസ്റ്റമർ സർവീസ്: റഫർ ചെയ്യുക webബന്ധപ്പെടാനുള്ള വിശദാംശങ്ങൾക്കുള്ള സൈറ്റ്.
