Sinopé Non-Programmable Expansion Unit for Floor Heating Thermostat TR1310 Instruction Manual

ആമുഖം

The Sinopé TR1310 Non-Programmable Expansion Unit is designed to increase the maximum load capacity of your Sinopé floor heating thermostat. This unit is essential for large floor heating areas exceeding 15 amperes, allowing a single master thermostat to control multiple floor heating sections efficiently. By integrating this expansion unit, you can manage extensive heated floor areas without the need for additional thermostats, optimizing your heating system and potentially reducing costs.

This manual provides detailed instructions for the safe and correct installation, operation, and maintenance of your TR1310 expansion unit. Please read all instructions carefully before beginning installation or use.

ഉൽപ്പന്ന സവിശേഷതകൾ

• Compatible with Floor Heating: Works seamlessly with any Sinopé smart, programmable, or non-programmable floor heating thermostat.
• Increased Load Capacity: Multiplies the allowed maximum load by combining this expansion unit with any compatible floor heating thermostat, enabling control of large floor heating installations exceeding 15 A.
• വികസിപ്പിക്കാവുന്ന സിസ്റ്റം: Connect up to 10 expansion units per thermostat for extensive coverage.
• ഇൻസ്റ്റാൾ ചെയ്യാൻ എളുപ്പമാണ്: Designed for straightforward setup with a handy installation guide.
• സംയോജിത സുരക്ഷ: Equipped with a built-in Class A Ground Fault Circuit Interrupter (GFCI) and protection for engineered wood flooring.

പാക്കേജ് ഉള്ളടക്കം

Upon opening the product box, verify that all components are present and undamaged:

• Sinopé TR1310 Expansion Unit
• ഇൻസ്ട്രക്ഷൻ മാനുവൽ
• Floor Temperature Sensor (if applicable)
• Wire Nuts / Connectors
• മൗണ്ടിംഗ് സ്ക്രൂകൾ
• Small Screwdriver (for terminal connections)

Image: Sinopé TR1310 Non-Programmable Expansion Unit in its packaging, showing the main unit, sensor cable, wire nuts, and instruction manual.

സുരക്ഷാ വിവരങ്ങൾ

മുന്നറിയിപ്പ്: Risk of electric shock. Installation must be performed by a qualified electrician in accordance with local and national electrical codes. Disconnect power at the main service panel before installing or servicing this unit.

• Always turn off the main power supply at the circuit breaker before performing any electrical work.
• വൈദ്യുതാഘാതം തടയാൻ ശരിയായ ഗ്രൗണ്ടിംഗ് ഉറപ്പാക്കുക.
• Do not use the unit if it appears damaged.
• This unit is designed for resistive loads only.
• ഓപ്പറേറ്റിംഗ് വോളിയംtage: 120/208/240 Vac, 50/60 Hz.
• Maximum load: 3600 W @ 240 V / 15 A.

ഇൻസ്റ്റലേഷൻ

Professional installation by a qualified electrician is highly recommended to ensure safety and compliance with electrical codes.

ഘട്ടം 1: ഇൻസ്റ്റാളേഷനായി തയ്യാറെടുക്കുക

1. Turn off the power to the floor heating circuit at the main electrical panel.
2. Remove the existing thermostat (if any) and identify the power supply wires (Line 1, Line 2/Neutral) and the heating element wires (Load 1, Load 2).
3. Separate the front panel of the TR1310 expansion unit from its back plate using a small screwdriver.

Step 2: Wiring the Expansion Unit

The TR1310 unit has pre-attached wires for connection. Ensure all connections are secure and insulated with wire nuts.

• Connect Heating Element Wires (Load): The expansion unit has two wires labeled 'LOAD' (typically black and white, or as indicated by stickers). Connect these to the wires leading to your floor heating element (e.g., heating cable, heating film, or heating mat) using the provided wire nuts.
• Connect Power Supply Wires (Line): The unit also has two wires for power supply (Line 1 and Line 2/Neutral). Connect these to your main power supply wires from the electrical panel. The unit is dual voltage compatible (120VAC or 240VAC).
• Connect Floor Temperature Sensor: If using a floor temperature sensor, connect its two wires to the designated sensor terminals (typically labeled 'Sensor' or with numbers 1 and 2) on the back plate of the expansion unit. Tighten the terminal screws to secure the connections.

ഘട്ടം 3: യൂണിറ്റ് മൌണ്ട് ചെയ്യുന്നു

1. എല്ലാ വയറുകളും ശ്രദ്ധാപൂർവ്വം ഇലക്ട്രിക്കൽ ബോക്സിൽ തിരുകുക.
2. Secure the back plate of the expansion unit to the electrical box using the provided mounting screws.
3. Align the front panel with the back plate and gently push until it clicks into place. Ensure the pins are straight and not bent.

Step 4: Initial Power-Up and GFCI Test

1. Restore power to the circuit at the main electrical panel.
2. The unit should power on. Locate the GFCI test button (usually on the side or bottom of the unit).
3. Press the GFCI test button. The unit should trip, indicating the GFCI is functioning correctly.
4. Press the reset button (if separate) or cycle the power to reset the GFCI.

പ്രവർത്തന നിർദ്ദേശങ്ങൾ

The Sinopé TR1310 is a non-programmable expansion unit, meaning its primary function is to extend the load capacity of a master thermostat. It does not have independent temperature controls or scheduling features. All temperature settings and programming are managed by the connected master Sinopé thermostat.

GFCI Test and Reset

The built-in GFCI is a critical safety feature. It is recommended to test the GFCI monthly.

• To test, press the 'TEST' button on the unit. The unit should trip, cutting power to the heating element.
• To reset, press the 'RESET' button (if available) or cycle the power to the unit.
• If the GFCI does not trip or reset correctly, discontinue use and contact a qualified electrician.

മെയിൻ്റനൻസ്

The Sinopé TR1310 expansion unit requires minimal maintenance.

• വൃത്തിയാക്കൽ: Wipe the unit's surface with a soft, damp തുണി. ഉരച്ചിലുകളുള്ള ക്ലീനറുകളോ ലായകങ്ങളോ ഉപയോഗിക്കരുത്.
• Periodic GFCI Testing: Test the GFCI monthly as described in the Operating Instructions section to ensure continued safety.
• പരിശോധന: Periodically inspect the unit and wiring for any signs of damage or wear. If any issues are found, disconnect power and contact a qualified electrician.

ട്രബിൾഷൂട്ടിംഗ്

If you experience issues with your TR1310 expansion unit, refer to the following common troubleshooting steps:

• യൂണിറ്റ് പവർ ചെയ്യുന്നില്ല:
  • Check the circuit breaker for the floor heating circuit.
  • എല്ലാ വയറിംഗ് കണക്ഷനുകളും സുരക്ഷിതമാണെന്ന് ഉറപ്പാക്കുക.
  • Verify the main power supply is active.
• GFCI Trips Frequently:
  • This indicates a ground fault. Inspect the heating element and wiring for damage.
  • Ensure the unit is not exposed to moisture.
  • Contact a qualified electrician to diagnose and repair the fault.
• Floor Not Heating:
  • Check the settings on the master Sinopé thermostat.
  • Ensure the GFCI on the expansion unit has not tripped.
  • Verify the heating element is properly connected and functional.

For issues not resolved by these steps, please contact Sinopé Technologies customer support or a qualified electrician.

സ്പെസിഫിക്കേഷനുകൾ

വാറൻ്റിയും പിന്തുണയും

വാറൻ്റി വിവരണം: This Sinopé product is covered by a 3-year manufacturer limited warranty from the date of purchase.

നിർമ്മാതാവ്: Sinopé Technologies

ബിസിനസ് സ്ഥലം: Sinopé Technologies Inc., 705 av. Montrichard, Saint-Jean-sur-Richelieu, QC, Canada, J2X 5K8.

ഉപഭോക്തൃ പിന്തുണ: For technical assistance or warranty claims, please contact Sinopé Technologies at 1-855-741-7701 or visit their official webസൈറ്റ്.