Bison Express Wood Glue D2 - 750g Instruction Manual

1. ഉൽപ്പന്നം കഴിഞ്ഞുview

Bison Express Wood Glue is a high-quality, D2-rated vinyl adhesive designed for strong and durable wood bonding. This solvent-free glue is moisture-resistant, dries quickly, and becomes transparent upon drying, making it suitable for various indoor applications. It is also paintable after curing.

Image of the yellow bottle of Bison Express Wood Glue with a red cap, showing the brand logo and product name. This 750g bottle is designed for easy application.

പ്രധാന സവിശേഷതകൾ:

• D2 Moisture Resistance: Suitable for indoor use with occasional short-term exposure to high humidity or water.
• Stronger Than Wood: Creates a bond that is typically stronger than the wood itself.
• വേഗത്തിലുള്ള ഉണക്കൽ: Accelerates project completion.
• Transparent After Drying: Ensures a clean finish.
• പെയിന്റ് ചെയ്യാവുന്നത്: Can be painted over once fully cured.
• Solvent-Free: Safer for use and environmentally friendlier.
• താപനില പ്രതിരോധം: Withstands temperatures from -20°C to +60°C.

2 സുരക്ഷാ വിവരങ്ങൾ

Always read the product label before use. Keep out of reach of children. Avoid contact with skin and eyes. In case of contact, rinse immediately with plenty of water. If swallowed, seek medical advice immediately and show this container or label. Use in a well-ventilated area. Do not empty into drains.

3. തയ്യാറാക്കൽ

1. ഉപരിതല അവസ്ഥ: Ensure all surfaces to be bonded are clean, dry, free of grease, and dust.
2. താപനില: Apply at room temperature (ideally between +5°C and +30°C).
3. ഉപകരണങ്ങൾ: Have a fine-toothed glue comb (1 mm) or a brush ready for application, along with clamps or presses.

4 അപേക്ഷ

1. പശ പ്രയോഗിക്കുക: Apply a thin, even layer of Bison Express Wood Glue to one or both surfaces to be bonded. Use a fine-toothed glue comb (1 mm) or a brush for even distribution.
2. തുറക്കുന്ന സമയം: Allow the glue to penetrate for a few minutes.
3. കൂട്ടിച്ചേർക്കുക: Join the two parts within 8 minutes of applying the glue.
4. Press/Clamp: Immediately clamp or press the assembled parts together for a minimum of 60 minutes. The recommended pressure is 2-5 kg/cm².

5. Drying and Curing

• Clampസമയം: Minimum 60 minutes under pressure.
• Initial Strength: Achieved quickly, allowing for further processing.
• Full Cure: The glue reaches its full strength and moisture resistance after approximately 24 hours, depending on temperature, humidity, and material porosity.
• സുതാര്യത: The glue will dry transparent.

6 വൃത്തിയാക്കലും സംഭരണവും

• Wet Glue: Remove wet glue residues immediately with water.
• Dried Glue: Dried glue residues are very difficult to remove. Mechanical removal may be necessary.
• സംഭരണം: Store the product in a cool, dry, and frost-free place. Ensure the cap is tightly closed.
• ഷെൽഫ് ലൈഫ്: Refer to the product packaging for specific shelf life information.

7. പ്രശ്‌നപരിഹാരം

• മോശം അഡീഷൻ:
  • Ensure surfaces are clean, dry, and free of contaminants (grease, dust).
  • Verify sufficient clamping pressure and duration.
  • Check ambient temperature; very low temperatures can affect curing.
• Slow Drying:
  • High humidity or low temperatures can extend drying times.
  • Excessive glue application can also prolong drying.
• Visible Glue Line:
  • While the glue dries transparent, excessive squeeze-out or uneven application can still be visible. Clean excess glue immediately.

8 സ്പെസിഫിക്കേഷനുകൾ

9. വാറൻ്റിയും പിന്തുണയും

For specific warranty information, please refer to the official Bison website or contact their customer support directly. Keep your purchase receipt as proof of purchase. For technical assistance or product inquiries, please visit the manufacturer's webസൈറ്റ് അല്ലെങ്കിൽ അവരുടെ ഉപഭോക്തൃ സേവന വിഭാഗവുമായി ബന്ധപ്പെടുക.

നിർമ്മാതാവ്: കാട്ടുപോത്ത്