1. ആമുഖം
The Lumenier 30A BLHeli_S ESC is an Electronic Speed Controller designed for high-performance RC applications, particularly multirotors. It features the powerful BusyBee2 (EFM8BB21F16) chip, operating at 48MHz, which provides precise motor control and takes full advantage of the BLHeli_S firmware. This ESC is compact, lightweight, and supports various digital and analog protocols for versatile integration into your system.
2 പ്രധാന സവിശേഷതകൾ
- പ്രോസസ്സർ: New BusyBee2 MCU (EFM8BB21F16) operating at 48MHz, supporting up to 500k eRPM.
- ഫേംവെയർ: Improved BLHeli_S firmware pre-installed.
- PWM Driver: Hardware PWM controller at 36KHz for ultra-smooth throttle response and near-silent motor operation.
- പ്രോട്ടോക്കോൾ പിന്തുണ: Compatible with DSHOT, Oneshot125 (125-250us), Oneshot42 (41.7-83.3us), and Multishot (5-25us). Features auto-detection.
- ഡിസൈൻ: Ultra-lightweight and compact size for easy integration.
- മോട്ടോർ അനുയോജ്യത: Adaptive timing, compatible with a wide range of motors and Kv values.
- കാര്യക്ഷമത: Synchronous rectification technology enhances efficiency and provides dampഎഡ് ലൈറ്റ്.
- ബ്രേക്കിംഗ്: Powerful regenerative braking / active braking.
- ബാറ്ററി അനുയോജ്യത: Supports 2-4s LiPo batteries.
- കോൺഫിഗറേഷൻ: OPTO (no BEC) design.
3. സജ്ജീകരണവും ഇൻസ്റ്റാളേഷനും
3.1 വയറിംഗ് കണക്ഷനുകൾ
The Lumenier 30A BLHeli_S ESC comes pre-soldered with motor, signal, and power wires for convenience.
- മോട്ടോർ വയറുകൾ: Connect the three motor wires to your brushless motor. The order may affect motor rotation direction; this can be adjusted in BLHeli_S configurator if needed.
- Signal Wire: Connect the signal wire to the appropriate motor output pin on your flight controller.
- പവർ വയറുകൾ: Connect the red (+) and black (-) power wires to your LiPo battery distribution board or direct battery connection. Ensure correct polarity.
Image 1: Lumenier 30A BLHeli_S ESC showing the main board and pre-soldered motor, signal, and power wires.
Image 2: Lumenier 30A BLHeli_S ESC with protective heat shrink, showing the signal wire connector and power leads.
3.2 ഫേംവെയറും കോൺഫിഗറേഷനും
The ESC comes with BLHeli_S firmware pre-installed. No initial firmware installation is required.
- Protocol Auto-Detection: The ESC automatically detects the protocol (PWM, Oneshot125, Oneshot42, Multishot, etc.) enabled in your flight controller software. Simply enable the desired feature in your flight controller's configuration.
- BLHeli Configurator: For advanced settings, motor direction changes, or firmware updates, use the official BLHeli Configurator software. This tool allows you to fine-tune ESC parameters. You can download the latest version from the official BLHeli resources.
4. ഓപ്പറേഷൻ
Once properly installed and configured with your flight controller, the Lumenier 30A BLHeli_S ESC will operate seamlessly.
- Smooth Throttle: The 36KHz hardware PWM driver ensures a very smooth and responsive throttle curve.
- മോട്ടോർ ശബ്ദം: Expect near-silent motor operation due to the high PWM frequency.
- Adaptive Timing: The ESC automatically adjusts motor timing for optimal performance across various motors and Kv ratings.
- Active Braking: The powerful regenerative braking (damped light) feature provides quick motor response and improved flight characteristics.
5 സ്പെസിഫിക്കേഷനുകൾ
| ഫീച്ചർ | വിശദാംശങ്ങൾ |
|---|---|
| ഇൻപുട്ട് വോളിയംtage | 2-4s LiPoly |
| സ്ഥിരമായ കറൻ്റ് | 30 Amps |
| ബേസ്റ്റ് കറന്റ് | 35 Amps |
| ബി.ഇ.സി | No BEC, OPTO only |
| അളവുകൾ | 28mm x 14mm x 5mm |
| Signal Wire Length | 15 സെ.മീ |
| Motor/Power Wire Length | 9 സെ.മീ |
| ഭാരം | 5g (without motor wires) |
| എം.സി.യു | BusyBee2 (EFM8BB21F16) |
| പിഡബ്ല്യുഎം ഫ്രീക്വൻസി | 36KHz (Hardware PWM) |
| പിന്തുണയ്ക്കുന്ന പ്രോട്ടോക്കോളുകൾ | DSHOT, Oneshot125, Oneshot42, Multishot |
6. പരിപാലനം
The Lumenier 30A BLHeli_S ESC is designed for durability and reliability. Minimal maintenance is required.
- പരിശോധന: Periodically inspect the ESC for any signs of physical damage, loose connections, or burnt components.
- വൃത്തിയാക്കൽ: Keep the ESC free from dust, dirt, and moisture. Use compressed air or a soft brush for cleaning.
- ചൂട് മാനേജ്മെൻ്റ്: Ensure adequate airflow around the ESC during operation to prevent overheating, especially in enclosed spaces.
- ഫേംവെയർ അപ്ഡേറ്റുകൾ: Check the official BLHeli resources periodically for any new firmware updates that may offer performance improvements or bug fixes.
7. പ്രശ്നപരിഹാരം
If you encounter issues with your Lumenier 30A BLHeli_S ESC, consider the following troubleshooting steps:
- മോട്ടോർ കറങ്ങുന്നില്ല:
- Check all wiring connections between the ESC, motor, and flight controller for continuity and correct polarity.
- Verify that the flight controller is sending a valid signal to the ESC.
- Ensure the motor is not physically obstructed.
- ക്രമരഹിതമായ മോട്ടോർ പെരുമാറ്റം:
- Confirm that the correct ESC protocol (DSHOT, Oneshot, etc.) is selected in your flight controller software.
- Check for any loose motor connections.
- Inspect the ESC for any visible damage or signs of overheating.
- ESC Not Powering Up:
- Ensure the battery is fully charged and connected with correct polarity.
- Check for any short circuits in the power lines.
- അമിത ചൂടാക്കൽ:
- Ensure adequate ventilation around the ESC.
- Verify that the motor and propeller combination is not drawing excessive current.
- Check for any motor issues that might cause high current draw.
For further assistance, refer to online resources for BLHeli_S firmware or contact Lumenier support.
8. വാറൻ്റിയും പിന്തുണയും
Lumenier products are manufactured to high standards. For specific warranty information, please refer to the official Lumenier webസൈറ്റിൽ പ്രവേശിക്കുക അല്ലെങ്കിൽ അവരുടെ ഉപഭോക്തൃ പിന്തുണയുമായി നേരിട്ട് ബന്ധപ്പെടുക.
For technical support, product inquiries, or warranty claims, please visit the Lumenier Store on Amazon അല്ലെങ്കിൽ അവരുടെ ഉദ്യോഗസ്ഥൻ webസൈറ്റ്.
