ZTW TY15124544

ZTW Mantis Slim 15A Brushless ESC Instruction Manual

മോഡൽ: TY15124544

1. ആമുഖം

The ZTW Mantis Slim 15A Brushless Electronic Speed Controller (ESC) is designed for F3P airplanes and gliders, offering super smooth startup and throttle response. This manual provides essential information for safe and efficient operation of your ESC. Please read it thoroughly before use.

2 പ്രധാന സവിശേഷതകൾ

3 സ്പെസിഫിക്കേഷനുകൾ

ഫീച്ചർമൂല്യം
ESC Size (LxWxH)27mm x 14mm x 5.5mm
ഇൻപുട്ട് പവർ2-4S Lipo / 5-12NC
BEC ഔട്ട്പുട്ട്2A/5V (3A peak)
തുടർച്ചയായ കറൻ്റ്15എ
ഭാരം6.8 ഗ്രാം
മോട്ടോർ കണക്റ്റർ2.0mm female bullet connector
പവർ കണക്റ്റർJST (female case with male pin)

Product Dimensions: 1.2 x 1 x 0.1 inches. Item Weight: 0.64 ounces.

ZTW Mantis Slim 15A ESC with detailed dimensions

Figure 1: ZTW Mantis Slim 15A ESC with detailed dimensions (Length: 27mm, Width: 14mm, Height: 5.5mm).

4. സജ്ജീകരണവും ഇൻസ്റ്റാളേഷനും

Proper installation is crucial for the performance and safety of your ESC. Follow these steps carefully:

4.1 വയറിംഗ് കണക്ഷനുകൾ

ZTW Mantis Slim 15A ESC with labeled 2.0mm female bullet motor connectors and JST female power connector

Figure 2: ZTW Mantis Slim 15A ESC showing 2.0mm female bullet motor connectors and JST female power connector.

4.2 ESC മൌണ്ട് ചെയ്യുന്നു

Choose a location that has good airflow to offer best cooling to prevent overheating. Do NOT cover the side with the flat heat shield with hook and loop tape or any other material as this will greatly lower its effectiveness. Mount the ESC with a combination of hook and loop tape or 2-sided foam tape.

Video 1: Brushless ESC for Drone & RC Plane Easy to install (Source: HAWK'S WORK). This video demonstrates the general installation process of a Brushless ESC for a Drone or RC Plane, highlighting easy installation steps.

5. പ്രവർത്തന നിർദ്ദേശങ്ങൾ

Always perform throttle calibration before the first use or if you change your transmitter.

5.1 ത്രോട്ടിൽ കാലിബ്രേഷൻ

  1. നിങ്ങളുടെ റേഡിയോ ഓണാക്കി ത്രോട്ടിൽ സ്റ്റിക്ക് മുകളിലെ സ്ഥാനത്ത് വയ്ക്കുക.
  2. Connect the battery pack to the ESC. Wait for about 2 seconds, the motor will beep twice, then pull the throttle to the minimum position. The motor will also beep, which indicates that your ESC has got the signal range of the throttle from your transmitter.

Video 2: How to do throttle calibration for Mantis Slim G2 20A/30A (Source: ZTW Model). This video provides instructions on how to perform throttle calibration for the Mantis Slim G2 20A/30A ESC, which is applicable to the 15A model.

Video 3: How to calibrate ESC (Source: HAWK'S WORK). This video demonstrates the general process of calibrating an ESC, which can be helpful for understanding the throttle calibration process.

5.2 Programming the ESC

The ZTW Mantis Slim ESC can be programmed using a ZTW Beatles series programming card or directly via your transmitter.

5.2.1 Using an LCD Program Card

  1. Unplug the ESC throttle cable from the receiver.
  2. Insert the LCD Program Card G2 into the ESC's throttle cable port.
  3. Connect the ESC to the battery.
  4. Wait for the LCD screen to display the power-on interface.
  5. Press the "ITEM" or "OK" button to enter the parameter setting interface.
  6. Use the navigation buttons to select parameters and adjust values.
  7. Upon completion of programming, press the "OK" button to save the parameters.

Video 4: How to set parameter for Mantis Slim G2 20A/30A by LCD Card (Source: ZTW Model). This video demonstrates how to set parameters for Mantis Slim G2 20A/30A using an LCD Card, which is applicable to the 15A model.

5.2.2 Setting SMR (Switch Motor Rotation) Function

The SMR function allows you to change the motor rotation direction. It is only allowed to be used when the aircraft is landing on the ground, and it can effectively shorten the landing distance of the aircraft.

Video 5: Set the SMR (Reverse) function of your ESC (Source: TOYTENSI). This video explains how to set the SMR (Switch Motor Rotation) function for your ESC, which is useful for controlling motor direction during landing.

6. പരിപാലനം

To ensure the longevity and optimal performance of your ZTW Mantis Slim ESC, follow these maintenance guidelines:

7. പ്രശ്‌നപരിഹാരം

നിങ്ങളുടെ ESC-യിൽ പ്രശ്നങ്ങൾ നേരിടുകയാണെങ്കിൽ, ഇനിപ്പറയുന്ന പൊതുവായ ട്രബിൾഷൂട്ടിംഗ് ഘട്ടങ്ങൾ പരിഗണിക്കുക:

8 സുരക്ഷാ വിവരങ്ങൾ

Always prioritize safety when operating RC equipment. Failure to do so may result in property damage, injury, or death.

9. വാറണ്ടിയും പിന്തുണയും

ZTW and HAWK HOBBY offer a 100% free warranty for this ESC. For any issues or support needs, please contact your retailer or the manufacturer directly.

അനുബന്ധ രേഖകൾ - TY15124544

പ്രീview ZTW Mantis Slim G2 15A ESC User Manual
User manual for the ZTW Mantis Slim G2 15A ESC, detailing features, specifications, setup, programming, and troubleshooting for RC aircraft. Learn how to calibrate, program, and maintain your ESC for optimal performance.
പ്രീview ZTW Mantis Slim G2 Series ESC User Manual
User manual for the ZTW Mantis Slim G2 Series Brushless Electronic Speed Controller (ESC), detailing features, specifications, setup, programming, and troubleshooting for RC applications.
പ്രീview ZTW സ്കൈഹോക്ക് സീരീസ് ESC ഉപയോക്തൃ മാനുവൽ
ZTW SkyHawk സീരീസ് ബ്രഷ്‌ലെസ് ഇലക്ട്രോണിക് സ്പീഡ് കൺട്രോളറുകൾ (ESC)ക്കായുള്ള ഉപയോക്തൃ മാനുവൽ, RC വിമാനങ്ങൾക്കും ഹെലികോപ്റ്ററുകൾക്കുമുള്ള സവിശേഷതകൾ, സ്പെസിഫിക്കേഷനുകൾ, ട്രബിൾഷൂട്ടിംഗ് എന്നിവ വിശദീകരിക്കുന്നു.
പ്രീview ZTW Beast Pro 30A G2 BLE Brushless ESC User Manual
User manual for the ZTW Beast Pro 30A G2 BLE ESC, covering features, specifications, calibration, app usage, and programmable settings for 1:28 RC cars.
പ്രീview ZTW Brushless ESC Program Card Instructions
Instructions for using the ZTW Brushless ESC Program Card to set up ZTW's Brushless Electronic Speed Controller parameters. Covers use with ESCs with and without built-in BEC.
പ്രീview ZTW Beast Pro 120A, 160A, 220A Brushless ESC User Manual
User manual for ZTW Beast Pro series brushless electronic speed controllers (ESC) models 120A, 160A, and 220A. This guide details features, specifications, setup, calibration, and advanced programming options for 1:10 & 1:12 scale RC cars and trucks, enhancing performance and driveability.