ഉൽപ്പന്നം കഴിഞ്ഞുview
The Emtek 7103 Passage Set is a high-quality knobset designed for doors that do not require a locking mechanism, such as closet doors, hallway doors, or pantry doors. This set includes a Madison Black Knob and a #3 Wrought Steel Rosette with a Flat Black Steel (FBS) finish. It is manufactured by Emtek and includes a standard rotation latch and strike plate. The knobset is designed for a standard 2-1/8 inch door preparation. The standard latch is for a 2-3/8 inch backset, with a 2-3/4 inch backset available if specified.
This image displays the Emtek 7103 Passage Set, featuring a round Madison Black Knob mounted on a rectangular Flat Black Wrought Steel Rosette. The knob has a smooth, glossy black finish, contrasting with the textured matte black finish of the rosette.
സജ്ജീകരണവും ഇൻസ്റ്റാളേഷനും
This section provides instructions for the proper setup and installation of your Emtek 7103 Passage Set.
നിങ്ങൾ ആരംഭിക്കുന്നതിന് മുമ്പ്
- Ensure all components are present: knobset, rosette, latch, strike plate, and mounting screws.
- Verify door thickness and backset requirements. Standard backset is 2-3/8 inches. If 2-3/4 inches is required, ensure you have the correct latch.
- Tools required: Phillips head screwdriver, tape measure, pencil.
ഇൻസ്റ്റലേഷൻ ഘട്ടങ്ങൾ
- വാതിൽ തയ്യാറാക്കുക: Ensure the door has a standard 2-1/8 inch bore hole for the knobset and a 1-inch bore hole for the latch.
- ലാച്ച് ഇൻസ്റ്റാൾ ചെയ്യുക: Insert the latch into the edge of the door, ensuring the bevel faces the door frame. Secure with screws.
- Install the Exterior Knob/Rosette: Place the exterior knob and rosette assembly through the 2-1/8 inch bore hole, aligning the spindle with the latch mechanism.
- Install the Interior Knob/Rosette: Place the interior knob and rosette assembly onto the spindle, aligning the mounting posts with the holes on the exterior rosette.
- അസംബ്ലി സുരക്ഷിതമാക്കുക: Insert and tighten the mounting screws through the interior rosette into the exterior rosette. Do not overtighten.
- സ്ട്രൈക്ക് പ്ലേറ്റ് ഇൻസ്റ്റാൾ ചെയ്യുക: Mark and chisel the door frame for the strike plate. Secure the strike plate with screws, ensuring the latch engages smoothly.
- ടെസ്റ്റ് ഓപ്പറേഷൻ: Rotate the knobs to ensure the latch retracts and extends freely. Check for smooth operation from both sides of the door.
പ്രവർത്തന നിർദ്ദേശങ്ങൾ
The Emtek 7103 Passage Set is designed for doors that do not require locking, such as closet doors, hallway doors, or pantry doors. It allows for free passage from both sides at all times.
- To open the door, simply turn the knob in either direction. The latch bolt will retract, allowing the door to open.
- To close the door, push the door shut. The latch bolt will automatically engage with the strike plate, holding the door closed.
മെയിൻ്റനൻസ്
Proper maintenance will ensure the longevity and smooth operation of your Emtek 7103 Passage Set.
- വൃത്തിയാക്കൽ: Clean the knob and rosette surfaces with a soft, damp cloth. Avoid abrasive cleaners, solvents, or polishes that may damage the finish.
- ലൂബ്രിക്കേഷൻ: Periodically apply a small amount of silicone-based lubricant to the latch mechanism to ensure smooth operation. Do not use oil-based lubricants as they can attract dust and grime.
- മുറുകുന്ന സ്ക്രൂകൾ: Over time, mounting screws may loosen. Periodically check and gently tighten any loose screws to maintain stability. Do not overtighten.
- പരിശോധന: Regularly inspect the knobset for any signs of wear, damage, or misalignment.
ട്രബിൾഷൂട്ടിംഗ്
| പ്രശ്നം | സാധ്യമായ കാരണം | പരിഹാരം |
|---|---|---|
| Knob is loose or wobbly. | മൗണ്ടിംഗ് സ്ക്രൂകൾ അയഞ്ഞതാണ്. | Tighten the mounting screws on the interior rosette. |
| ലാച്ച് സുഗമമായി പിൻവാങ്ങുന്നില്ല. | ലൂബ്രിക്കേഷന്റെ അഭാവം; മെക്കാനിസത്തിലെ അവശിഷ്ടങ്ങൾ. | Apply silicone-based lubricant to the latch bolt. Clean any visible debris. |
| Door does not close properly or rattles. | Strike plate misalignment; worn latch. | Adjust the strike plate position. If latch is worn, consider replacement. |
| Knob is stiff to turn. | Spindle misalignment; internal mechanism friction. | Loosen mounting screws slightly, adjust knob position, then retighten. Lubricate internal mechanism if accessible. |
സ്പെസിഫിക്കേഷനുകൾ
- മോഡൽ: Emtek 7103 Passage Set
- മെറ്റീരിയൽ: Wrought Steel
- നോബ് ശൈലി: Madison Black Knob
- Rosette Style: #3 Rosette
- പൂർത്തിയാക്കുക: Flat Black Steel (FBS)
- വാതിൽ തയ്യാറാക്കൽ: Standard 2-1/8" bore hole
- ബാക്ക്സെറ്റ്: Standard 2-3/8" (2-3/4" available upon request)
- UPC: 751125555226
വാറൻ്റിയും പിന്തുണയും
Emtek products are manufactured to high-quality standards. For specific warranty information regarding your Emtek 7103 Passage Set, please refer to the documentation provided with your purchase or visit the official Emtek webസൈറ്റ്. വാറന്റി നിബന്ധനകളും വ്യവസ്ഥകളും വ്യത്യാസപ്പെടാം.
For technical support, product inquiries, or assistance with installation or troubleshooting, please contact Emtek customer service directly. Their contact information can typically be found on their official webഉൽപ്പന്ന പാക്കേജിംഗിനുള്ളിൽ.
നിർമ്മാതാവ്: എംടെക്
ഉദ്യോഗസ്ഥൻ Webസൈറ്റ്: www.emtek.com
