Zerone Automatic Pump Control Pressure Switch Controller 110V User Manual

1. ഉൽപ്പന്നം കഴിഞ്ഞുview

The Zerone Automatic Pump Control Pressure Switch Controller is designed to automate the operation of various water pumps. It replaces traditional pump control systems, offering functions such as automatic pump start/stop, water level monitoring, and dry-run protection. This controller is suitable for well pumps, jet pumps, garden pumps, clarified water pumps, and centrifugal pumps.

Figure 1: Zerone Automatic Pump Control Pressure Switch Controller

2 പ്രധാന സവിശേഷതകൾ

• യാന്ത്രിക പ്രവർത്തനം: Starts and stops the pump automatically based on water demand.
• ഡ്രൈ-റൺ സംരക്ഷണം: Automatically stops the pump in case of water shortagകേടുപാടുകൾ തടയാൻ ഇ.
• സംയോജിത നിയന്ത്രണം: Replaces traditional pressure switches, pressure tanks, and check valves for a streamlined system.
• Efficient Power Handling: Supports 110V input, up to 1.1KW pump power, and a maximum current of 10A.
• ഉയർന്ന മർദ്ദ ശേഷി: Operates effectively up to 10 bar (1 MPa) pressure.
• വിശാലമായ അനുയോജ്യത: Works with self-priming, jet, garden, clarified water, and centrifugal pumps.

3. ഇൻസ്റ്റലേഷനും സജ്ജീകരണവും

Proper installation is crucial for the safe and efficient operation of the pump controller. If you are unsure about any steps, consult a qualified professional.

3.1 ഘടകങ്ങൾ കഴിഞ്ഞുview

ചിത്രം 2: കോണാകൃതിയിലുള്ളത് view of the controller showing inlet and outlet ports.

3.2 മൗണ്ടിംഗ്

Mount the controller vertically on a wall or stable surface using appropriate fasteners. Ensure it is protected from direct sunlight, rain, and freezing temperatures. The unit should be installed above the highest water level of the pump to prevent water ingress into the electrical components.

3.3 പ്ലംബിംഗ് കണക്ഷനുകൾ

1. Connect the pump's discharge pipe to the controller's inlet port (typically marked 'IN' or with an arrow indicating flow into the unit).
2. Connect the household water supply pipe to the controller's outlet port (typically marked 'OUT' or with an arrow indicating flow out of the unit).
3. Ensure all connections are watertight using thread sealant tape or appropriate gaskets.

ചിത്രം 3: ഉദാamples of pump controller installations with various pump types.

3.4 ഇലക്ട്രിക്കൽ കണക്ഷനുകൾ

This device operates on 110V AC. All electrical wiring should be performed by a qualified electrician in accordance with local codes and regulations.

1. ഏതെങ്കിലും വൈദ്യുത കണക്ഷനുകൾ നടത്തുന്നതിന് മുമ്പ് പ്രധാന വൈദ്യുതി വിതരണം വിച്ഛേദിക്കപ്പെട്ടുവെന്ന് ഉറപ്പാക്കുക.
2. Connect the power supply cable (110V AC) to the designated input terminals on the controller.
3. Connect the pump's power cable to the designated output terminals on the controller.
4. Secure all wiring connections and ensure proper grounding.

Figure 4: Additional installation scenarios for the pump controller.

4. ഓപ്പറേഷൻ

Once properly installed and powered, the Zerone Automatic Pump Control operates automatically.

4.1 പ്രാരംഭ ആരംഭം

1. Open a tap in your water system to allow water to flow.
2. Restore power to the controller. The 'Power on' indicator should illuminate.
3. The pump will start automatically. Allow it to run until water flows steadily from the open tap, indicating the system is primed.
4. Close the tap. The pump should continue to run for a few seconds to build pressure, then stop. The 'Pump on' indicator will turn off.

4.2 Automatic Function

The controller monitors water pressure and flow. When a tap is opened, the pressure drops, and the controller starts the pump. When the tap is closed, the pressure rises, and the controller stops the pump after a short delay.

4.3 Dry-Run Protection and Restart

If the pump runs without water (dry-run), the 'Failure' indicator will illuminate, and the pump will stop to prevent damage. To restart the pump after a dry-run event:

1. Ensure the water supply to the pump is restored.
2. അമർത്തുക പുനരാരംഭിക്കുക button on the controller. The pump will attempt to restart.
3. If the water supply is still insufficient, the 'Failure' indicator will re-illuminate, and the pump will stop again. Repeat the process once water supply is confirmed.

5. പരിപാലനം

The Zerone Automatic Pump Control is designed for minimal maintenance. However, regular checks can ensure longevity and optimal performance.

• കണക്ഷനുകൾ പരിശോധിക്കുക: Periodically check all plumbing and electrical connections for leaks or loose wiring. Tighten as necessary.
• വൃത്തിയുള്ള പുറം: കൺട്രോളറിന്റെ പുറംഭാഗം പൊടിയും അവശിഷ്ടങ്ങളും ഇല്ലാതെ വൃത്തിയായി സൂക്ഷിക്കുക. മൃദുവായ, ഡി ക്ലീനർ ഉപയോഗിക്കുക.amp വൃത്തിയാക്കാനുള്ള തുണി. ഉരച്ചിലുകളുള്ള ക്ലീനറുകളോ ലായകങ്ങളോ ഉപയോഗിക്കരുത്.
• ശീതകാലം: In areas prone to freezing, ensure the controller and connected pipes are drained or protected from freezing temperatures to prevent damage.

6. പ്രശ്‌നപരിഹാരം

പൊതുവായ പ്രശ്നങ്ങളും അവയുടെ പരിഹാരങ്ങളും അറിയാൻ താഴെയുള്ള പട്ടിക കാണുക.

7 സ്പെസിഫിക്കേഷനുകൾ

ചിത്രം 5: ഉൽപ്പന്ന അളവുകൾ.

8. വാറൻ്റിയും പിന്തുണയും

For warranty information or technical support, please contact Zerone customer service. Keep your purchase receipt and product model number (B07K6FWC17) handy for faster service.