KUS S3 Fuel and Water Tank Level Sensor (150mm) Instruction Manual

1. ഉൽപ്പന്നം കഴിഞ്ഞുview

The KUS S3 Fuel and Water Tank Level Sensor is designed for accurate measurement of liquid levels in tanks. Constructed from durable SUS316 stainless steel, it offers excellent corrosion resistance, making it suitable for marine and other demanding applications. This sensor operates on the principle of a magnetic field to control a reed on-off switch, ensuring a long lifespan and reliable performance.

പ്രധാന സവിശേഷതകൾ:

• നീളം: 150 മിമി
• Signal Output: 0-190ohm
• Assembly: BSP 1 1/4" thread twist-in, or NPT thread twist-in
• മിഴിവ്: 21 മിമി
• Material: SUS316 Stainless Steel
• Protection Rank: IP67
• പ്രവർത്തന താപനില: -40°C മുതൽ +85°C വരെ

Figure 1: KUS S3 Fuel and Water Tank Level Sensor (150mm) with wiring.

വിശദമായ ഓവറിനായിview of the product and its features, please watch the following video:

2. സജ്ജീകരണവും ഇൻസ്റ്റാളേഷനും

Proper installation is crucial for accurate readings and long-term performance. Follow these steps carefully:

1. ടാങ്ക് തയ്യാറാക്കുക: Ensure the tank is empty and clean before beginning installation.
2. മൗണ്ടിംഗ് ലൊക്കേഷൻ നിർണ്ണയിക്കുക: Select a flat surface on the top of the tank for mounting.
3. Mark and Drill: Use the provided gasket as a template to mark the center hole and screw holes. Drill the center hole with a 40mm opener. Drill smaller pilot holes for the screws.
4. Measure Tank Depth: Measure the internal depth of your tank from the mounting surface to the bottom. Ensure at least 1 inch of clearance between the float retaining collar and the tank bottom. The sensor length should be appropriate for your tank depth.
5. Install Gasket and Sensor: Place the gasket over the drilled holes. Insert the sensor into the tank, aligning the screw holes.
6. സെൻസർ സുരക്ഷിതമാക്കുക: Fasten the screws in a sequence (e.g., diagonally) to ensure even pressure. Do not overtighten to prevent damage and ensure a leak-free seal.

For a visual guide on installation, please refer to the following video:

3. Wiring and Operation

The KUS S3 sensor provides a 0-190ohm resistance output. It can be connected to compatible fuel or water level gauges that accept this signal range.

വയറിംഗ് നിർദ്ദേശങ്ങൾ:

• Connect the sensor's signal wire (typically blue or orange) to the gauge's signal input.
• Connect the sensor's ground wire (typically black) to the battery negative terminal and the gauge's ground input.
• Connect the gauge's positive power input (typically red) to the battery positive terminal.
• If your gauge has a backlight, connect its positive wire (typically orange) to a switched 12V or 24V positive source.

Once wired, the sensor's float mechanism will move with the liquid level, and the connected gauge will display the corresponding level. The gauge provides a smooth and consistent sweep for accurate readings.

4. പരിപാലനം

The KUS S3 sensor is designed for minimal maintenance due to its robust SUS316 stainless steel construction. However, periodic checks can ensure optimal performance:

• വിഷ്വൽ പരിശോധന: Periodically inspect the sensor for any physical damage, corrosion, or debris accumulation, especially if used in harsh environments.
• വൃത്തിയാക്കൽ: If necessary, gently clean the sensor rod and float with a soft cloth and appropriate cleaning solution for stainless steel. Avoid abrasive materials that could scratch the surface.
• കണക്ഷൻ പരിശോധന: എല്ലാ വൈദ്യുത കണക്ഷനുകളും സുരക്ഷിതമായും തുരുമ്പെടുക്കാതെയും നിലനിർത്തുന്നുവെന്ന് ഉറപ്പാക്കുക.

5. പ്രശ്‌നപരിഹാരം

If you encounter issues with your KUS S3 sensor, consider the following:

• കൃത്യമല്ലാത്ത വായനകൾ:
  • Check for proper sensor length relative to tank depth.
  • Verify electrical connections are secure and correctly wired.
  • Ensure the float moves freely along the sensor rod without obstruction.
  • Confirm the connected gauge is compatible with a 0-190ohm resistance signal.
• No Reading:
  • Check power supply to the gauge and sensor.
  • Inspect wiring for breaks or loose connections.
  • Test the sensor's resistance output directly with a multimeter if possible.
• Leaks at Mounting Point:
  • Ensure the gasket is properly seated and undamaged.
  • Verify screws are tightened evenly, but not excessively.

For further assistance, contact KUS customer support.

6 സ്പെസിഫിക്കേഷനുകൾ

7. വാറൻ്റിയും പിന്തുണയും

For warranty information and technical support, please refer to the official KUS website or contact your authorized dealer. Keep your purchase receipt for warranty claims.

ബന്ധപ്പെടാനുള്ള വിവരങ്ങൾ:

• KUS Americas Inc. Store on Amazon