1. ഉൽപ്പന്നം കഴിഞ്ഞുview
The ICON 12511 Hub Fitting is designed to facilitate the transition from polyethylene holding tanks to standard ABS plumbing systems. This essential component ensures a secure and leak-free connection in RV waste water and sanitation setups.
Image: The ICON 12511 3-inch Hub Fitting. This black, polyethylene fitting is cylindrical, featuring a wider opening at the top for connection to a holding tank and a narrower section at the bottom for ABS plumbing. An O-ring is included for a secure seal.
2. ബോക്സിൽ എന്താണുള്ളത്?
The package for the ICON 12511 Fitting, Hub, 3" includes the following components:
- One (1) ICON 12511 Holding Tank Fitting 3" Hub Fitting
- One (1) O-ring (pre-installed or included for the 3" female slip end)
3. സജ്ജീകരണവും ഇൻസ്റ്റാളേഷനും
This section provides instructions for the proper installation of the ICON 12511 Hub Fitting. Ensure all safety precautions are followed during installation.
3.1. Required Materials (Not Included)
- Butyl sealant (ICON part # 12062 recommended)
- Hose pipe clamp (appropriate size for 3" connection)
- Standard ABS plumbing adhesive/cement (for ABS connections)
3.2 ഇൻസ്റ്റലേഷൻ ഘട്ടങ്ങൾ
- Prepare the Holding Tank: Ensure the polyethylene holding tank has a molded collar suitable for a 3-inch hub connection. Clean the area around the collar thoroughly to remove any debris or residue.
- സീലന്റ് പ്രയോഗിക്കുക: Apply a generous amount of butyl sealant (e.g., ICON part # 12062) around the molded polyethylene collar of the holding tank. This will create a watertight seal between the tank and the hub fitting.
- Attach the Hub Fitting: Carefully slide the ICON 12511 Hub Fitting onto the molded polyethylene collar of the holding tank. Ensure the O-ring is properly seated within the female slip end of the hub to provide an initial seal.
- Cl ഉപയോഗിച്ച് സുരക്ഷിതമാക്കുകamp: Place a hose pipe clamp around the connection point where the hub fitting meets the holding tank's collar. Tighten the clamp securely to compress the butyl sealant and create a robust, leak-proof connection.
- Connect to ABS Plumbing: The 3-inch female slip end of the hub fitting is designed for connection to standard ABS plumbing. Use appropriate ABS plumbing adhesive/cement to join the hub fitting to your ABS drain pipe. Follow the adhesive manufacturer's instructions for curing times.
- ചോർച്ചയ്ക്കുള്ള പരിശോധന: After the adhesive has cured, fill the holding tank with water and inspect all connections for any signs of leaks. Address any leaks immediately before putting the system into full operation.
4. ഓപ്പറേഷൻ
The ICON 12511 Hub Fitting is a passive component designed to facilitate fluid transfer. Once properly installed, its operation is integrated with the overall RV waste water system. Ensure that all connected plumbing components are functioning correctly to allow for proper waste drainage.
5. പരിപാലനം
Regular inspection of the ICON 12511 Hub Fitting and surrounding plumbing is recommended to ensure long-term performance and prevent issues.
- വിഷ്വൽ പരിശോധന: Periodically check the hub fitting and its connections for any signs of cracks, wear, or leaks. Pay close attention to the areas where the butyl sealant and hose clamp are applied, as well as the ABS plumbing joints.
- ശുചിത്വം: While the fitting itself is part of a waste system, ensuring the exterior is free from excessive dirt or debris can help in visual inspections.
- മുദ്ര സമഗ്രത: If any leaks are detected, re-evaluate the application of the butyl sealant and the tightness of the hose pipe clamp. If necessary, disassemble, clean, reapply sealant, and re-secure the connection.
6. പ്രശ്നപരിഹാരം
This section addresses common issues that may arise with the ICON 12511 Hub Fitting.
- Leakage at Tank Connection:
- കാരണം: Insufficient butyl sealant, improperly seated O-ring, or loose hose pipe clamp.
- പരിഹാരം: Ensure adequate butyl sealant is applied. Verify the O-ring is correctly positioned. Tighten the hose pipe clamp. If leakage persists, disassemble, clean surfaces, reapply sealant, and reassemble.
- Leakage at ABS Plumbing Connection:
- കാരണം: Improper application of ABS adhesive/cement, insufficient curing time, or damaged ABS pipe.
- പരിഹാരം: Ensure proper technique for ABS cementing. Allow sufficient curing time as per adhesive manufacturer's instructions. Inspect ABS pipe for damage and replace if necessary.
- Difficulty Connecting to Tank/Plumbing:
- കാരണം: Incorrect sizing, debris in connection points, or manufacturing defect.
- പരിഹാരം: Verify that the tank collar and ABS pipe are indeed 3-inch compatible. Clean all connection surfaces. If the issue persists and sizing is correct, contact ICON customer support.
7 സ്പെസിഫിക്കേഷനുകൾ
| ആട്രിബ്യൂട്ട് | വിശദാംശങ്ങൾ |
|---|---|
| ബ്രാൻഡ് | ഐക്കൺ |
| മോഡൽ നമ്പർ | 12511 |
| വലിപ്പം | Standard (3 inch) |
| മെറ്റീരിയൽ | പോളിയെത്തിലീൻ |
| നിറം | കറുപ്പ് |
| ഇനത്തിന്റെ അളവുകൾ (L x W x H) | 5 x 5 x 9 ഇഞ്ച് |
| കണക്റ്റർ തരം | Coupling (3" female slip end) |
| ത്രെഡ് വലുപ്പം | 3 inch (NPT) |
| എക്സ്റ്റീരിയർ ഫിനിഷ് | കറുപ്പ് |
| ഇനത്തിൻ്റെ ഭാരം | 0.48 ഔൺസ് (ഏകദേശം 13.61 ഗ്രാം) |
| കഷണങ്ങളുടെ എണ്ണം | 1 |
| നിർമ്മാതാവ് | Icon Technologies Limited |
| യു.പി.സി | 628423125119 |
| ആദ്യം ലഭ്യമായ തീയതി | ഏപ്രിൽ 19, 2019 |
8. വാറൻ്റിയും പിന്തുണയും
For information regarding product warranty, returns, or technical support, please contact ICON Technologies Limited directly. Refer to the original product packaging or the manufacturer's official website for the most current contact details and warranty policy.
നിർമ്മാതാവ്: Icon Technologies Limited
Webസൈറ്റ്: Visit the ICON Store on Amazon (പൊതു ബ്രാൻഡ് വിവരങ്ങൾക്ക്)
