AURSINC MMDVM Duplex Hotspot Module V1.5.2 with OLED Display User Manual

1. ആമുഖം

The AURSINC MMDVM Duplex Hotspot Module V1.5.2 is designed for digital amateur radio communication, supporting various modes such as DMR, P-25, D-Star, and System Fusion. This module features a 0.96-inch OLED display and is compatible with a range of Raspberry Pi models, including Pi 1, 2/2B, 3/3B/3B+, 4/4B, Pi Zero, and Pi Zero 2W. It utilizes a 32-bit ARM processor and offers up to 10mW RF power. The duplex design allows for two time slots on DMR, enhancing communication capabilities.

Figure 1: AURSINC MMDVM Duplex Hotspot Module with antennas and SMA connectors.

2. പാക്കേജ് ഉള്ളടക്കം

താഴെ ലിസ്റ്റ് ചെയ്തിരിക്കുന്ന എല്ലാ ഇനങ്ങളും നിങ്ങളുടെ പാക്കേജിൽ ഉൾപ്പെടുത്തിയിട്ടുണ്ടെന്ന് ഉറപ്പാക്കുക:

• 1x MMDVM Duplex Hotspot Module
• 2x ആന്റിന
• 2x SMA socket (right-angle adapters)

Figure 2: Contents of the AURSINC MMDVM Duplex Hotspot Module package, including the module, two antennas, and two SMA right-angle adapters.

3. സജ്ജീകരണം

This section outlines the steps to physically set up your AURSINC MMDVM Duplex Hotspot Module with a Raspberry Pi.

3.1 അനുയോജ്യത

The module is compatible with the following Raspberry Pi models:

• റാസ്ബെറി പൈ 1
• Raspberry Pi 2/2B
• Raspberry Pi 3/3B/3B+
• Raspberry Pi 4/4B
• റാസ്ബെറി പൈ സീറോ
• റാസ്‌ബെറി പൈ സീറോ 2W

3.2 ഫിസിക്കൽ അസംബ്ലി

1. Attach the Module to Raspberry Pi: Carefully align the 40-pin GPIO header on the MMDVM Duplex Hotspot Module with the corresponding pins on your Raspberry Pi. Gently press down until the module is securely seated.
2. ആന്റിനകൾ ബന്ധിപ്പിക്കുക: Screw the two provided antennas onto the SMA connectors on the MMDVM module. Ensure they are finger-tight.
3. (Optional) Connect SMA Sockets: If your enclosure requires it, attach the two SMA right-angle adapters to the module's SMA ports before screwing on the antennas.
4. വൈദ്യുതി വിതരണം: Connect a stable 5V power supply to your Raspberry Pi. A power supply rated for at least 3.5A is recommended to prevent operational issues.

ചിത്രം 3: ഇൻസ്റ്റലേഷൻ ഉദാamples showing the MMDVM Duplex Hotspot Module mounted on different Raspberry Pi models, including Pi Zero and standard Pi boards, within various enclosures.

4. ഓപ്പറേഷൻ

Once the module is physically connected and your Raspberry Pi is powered on with appropriate software (e.g., Pi-Star), the module will begin operation. The onboard 0.96-inch OLED display provides real-time status information, and LEDs indicate various operational states.

4.1 LED സൂചകങ്ങൾ

The module features several LEDs to indicate its status:

• PWR: പവർ സൂചകം.
• SVC: Service indicator.
• COS: Carrier Operated Switch.
• പിടി: Push-To-Talk indicator.
• DMR: Digital Mobile Radio mode indicator.
• YSF: Yaesu System Fusion mode indicator.
• P25: Project 25 mode indicator.
• NXDN: Next Generation Digital Narrowband mode indicator.

ചിത്രം 4: വിശദമായ ഒരു view of the MMDVM Duplex Hotspot Module, highlighting the 0.96-inch OLED display and the array of status LEDs (PWR, SVC, COS, PTT, DMR, YSF, P25, NXDN).

4.2 Duplex Functionality

This module supports duplex operation, allowing for two independent time slots on DMR. This enables more efficient use of the radio spectrum and can facilitate simultaneous communication paths.

5. Configuration Tips

Proper software configuration is essential for optimal performance. These tips are primarily for use with Pi-Star software.

5.1 Pi-Star Settings

• മോഡം തിരഞ്ഞെടുക്കൽ: In the Pi-Star configuration, select STM32_HS_GPIO as the modem type. Any modem type ending in GPIO should be supported.
• Radio/Modem Type: ഇത് സജ്ജമാക്കുക STM32-DVM/MMDVM_HS-Raspberry pi Hat(GPIO).
• ഫ്രീക്വൻസി ക്രമീകരണങ്ങൾ:
  • UHF: 433-900MHz
  • VHF: 144-220 MHz (Main band: 144-148, 219-225, 420-475, 842-950)
  • Recommended amateur band: 430-440 MHz.
  • കുറിപ്പ്: Set TX = 0, RX = 0 in the frequency configuration.
• OLED Display Configuration:
  • To ensure the screen remains on:
    1. In the Pi-Star configuration, set "OLED Type" to "OLED Type 3".
    2. Set "Port" to "modem".
    3. In the Expert section, navigate to "MMDVM host" and scroll to the "OLED" section.
    4. സജ്ജമാക്കുക LogoScreensaver വരെ 1. This setting prevents the screen from going blank when idle.
• മോഡ് തിരഞ്ഞെടുക്കൽ: Choose between DUPLEX Mode and SIMPLE Mode based on your operational requirements.

5.2 ഫേംവെയർ അപ്‌ഡേറ്റ്

To update the firmware, access the Pi-Star terminal via SSH (user: pi-star, pass: raspberry) and run the following command:

sudo pistar-mmdvmhshatflash hs_dual_hat

If the above command does not work, refer to the official MMDVM documentation or community resources for alternative update methods.

6. പരിപാലനം

The AURSINC MMDVM Duplex Hotspot Module is designed for reliable operation with minimal maintenance. Adhering to these guidelines will help ensure its longevity:

• ശുചിത്വം: Keep the module free from dust and debris. Use a soft, dry cloth for cleaning. Avoid liquid cleaners.
• പരിസ്ഥിതി വ്യവസ്ഥകൾ: Operate the module in a dry environment, away from extreme temperatures and humidity.
• വൈദ്യുതി വിതരണം: Always use a stable and appropriately rated 5V power supply for your Raspberry Pi to prevent damage or erratic behavior.
• ഫേംവെയർ അപ്‌ഡേറ്റുകൾ: Periodically check for and apply firmware updates as recommended by the Pi-Star community or AURSINC to benefit from performance improvements and bug fixes.

7. പ്രശ്‌നപരിഹാരം

If you encounter issues with your MMDVM Duplex Hotspot Module, refer to the following common problems and solutions:

7.1 OLED Display Not Lighting Up

• GPIO Conflicts: Ensure no other HATs or devices are connected to the Raspberry Pi's GPIO pins that might conflict with the OLED display's pins. Remove any conflicting accessories and retest.
• സോഫ്റ്റ്‌വെയർ കോൺഫിഗറേഷൻ: Verify that "OLED Type 3" is selected in Pi-Star's display type field and "Port" is set to "modem". Also, confirm that LogoScreensaver ആയി സജ്ജീകരിച്ചിരിക്കുന്നു 1 in the MMDVM host expert settings.
• സുരക്ഷിത കണക്ഷൻ: Ensure the MMDVM module is securely seated on the Raspberry Pi's GPIO header.

7.2 Module Not Functioning Correctly (e.g., No Transmit/Receive)

• വൈദ്യുതി വിതരണം: An underpowered Raspberry Pi can cause instability. Use a robust 5V power supply rated for at least 3.5A.
• മോഡം തിരഞ്ഞെടുക്കൽ: Double-check that STM32_HS_GPIO is correctly selected as the modem type in Pi-Star.
• ഫ്രീക്വൻസി ക്രമീകരണങ്ങൾ: Confirm that TX and RX frequencies are correctly configured (TX=0, RX=0) and within the module's operating range.
• ഫേംവെയർ: Ensure the module's firmware is up to date. Refer to the firmware update section.
• ആന്റിന കണക്ഷൻ: Verify that both antennas are securely connected to the module.

7.3 General Instability or Errors

• Pi-Star Logs: Check the Pi-Star dashboard logs for any error messages that might indicate the root cause.
• Re-flash Pi-Star: If software configuration becomes problematic, consider re-flashing your Pi-Star SD card with a fresh image.
• കമ്മ്യൂണിറ്റി പിന്തുണ: Consult online forums and communities dedicated to MMDVM hotspots and Pi-Star for further assistance.

8 സ്പെസിഫിക്കേഷനുകൾ

9. വാറൻ്റിയും പിന്തുണയും

9.1 ഉപഭോക്തൃ പിന്തുണ

AURSINC is dedicated to providing professional electronic products and customer satisfaction. If you have any questions, concerns, or require assistance with your MMDVM Duplex Hotspot Module, please contact AURSINC customer support. You can typically find contact information on the official AURSINC webസൈറ്റ് അല്ലെങ്കിൽ നിങ്ങളുടെ വാങ്ങൽ പ്ലാറ്റ്‌ഫോം വഴി.

For additional resources and community support, consider visiting online forums and groups dedicated to MMDVM hotspots and Pi-Star software, where experienced users often share valuable insights and troubleshooting tips.

9.2 ഉൽപ്പന്ന വാറന്റി

Specific warranty details may vary by region and retailer. Please refer to the documentation provided with your purchase or contact AURSINC customer support for information regarding the product warranty.