RunCam Hybrid 2 4K FPV and HD Recording Camera Instruction Manual

ആമുഖം

The RunCam Hybrid 2 is an advanced dual-lens camera system designed for FPV (First Person View) applications and high-definition (HD) video recording. It integrates a 4K HD recording lens with a dedicated analog Phoenix 2 sensor lens, providing both high-quality recorded footage and a clear, low-latency FPV feed. This manual provides essential information for the proper installation, operation, and maintenance of your RunCam Hybrid 2 camera.

ഉൽപ്പന്നം കഴിഞ്ഞുview

The RunCam Hybrid 2 features a compact, single-board design, making it suitable for micro FPV setups. Its dual-lens configuration ensures that the FPV view closely matches the recorded HD footage, enhancing the piloting experience.

പ്രധാന സവിശേഷതകൾ:

• ഡ്യുവൽ ലെൻസ് സിസ്റ്റം: Combines a 4K HD recording lens (SONY 8MP sensor) with an analog FPV lens (Phoenix 2, SONY 1.3MP sensor).
• Single Board Design: Achieves a compact form factor with both lenses mounted closely on a single PCB.
• എളുപ്പമുള്ള ഇൻസ്റ്റാളേഷൻ: 19mm camera module width allows direct mounting in micro FPV frames without adapters.
• QR Code Parameter Settings: Configure camera settings conveniently via a smartphone app by scanning a generated QR code.
• UART നിയന്ത്രണം: Connects to a flight controller's UART port for remote control of recording functions via your radio transmitter.

Image: Analog Output Upgraded to Phoenix 2. The camera provides an improved FPV image feed.

Image: Single board design for simple installation.

പാക്കേജ് ഉള്ളടക്കം

താഴെ ലിസ്റ്റ് ചെയ്തിരിക്കുന്ന എല്ലാ ഇനങ്ങളും നിങ്ങളുടെ പാക്കേജിൽ ഉൾപ്പെടുത്തിയിട്ടുണ്ടെന്ന് ഉറപ്പാക്കുക:

• 1x RunCam Hybrid 2 Camera
• 1x Plastic cover
• 1x 3PIN FPV silicone cable (male)
• 1x 3PIN FPV silicone cable (female)
• 1x Set of M2 screws
• 1x മാനുവൽ

Image: Package contents of the RunCam Hybrid 2.

സ്പെസിഫിക്കേഷനുകൾ

Image: RunCam Hybrid 2 Dimensions.

സജ്ജമാക്കുക

Follow these steps to properly set up your RunCam Hybrid 2 camera:

1. ഫിസിക്കൽ ഇൻസ്റ്റലേഷൻ: Mount the 19mm camera module into your drone or vehicle frame. The compact design allows for direct integration into micro FPV setups.
2. വയറിംഗ് കണക്ഷനുകൾ: Refer to the wiring diagram below for correct connections.
   • VCC+ (5-20V): നിർദ്ദിഷ്ട വോള്യത്തിനുള്ളിൽ ഒരു സ്ഥിരതയുള്ള DC പവർ സ്രോതസ്സിലേക്ക് കണക്റ്റുചെയ്യുക.tagഇ ശ്രേണി. Warning: Do not directly power with a 4S battery or higher, as this can cause overvoltage and damage the camera.
   • GND: നിലവുമായി ബന്ധിപ്പിക്കുക.
   • വീഡിയോ: Connect to your FPV video transmitter (VTX) for analog video output.
   • TX/RX: Connect to a UART port on your flight controller for remote control functionality and firmware updates.
3. Micro SD Card Insertion: Insert a formatted Micro SD card (FAT32 format, U3 speed class recommended for 2.7K60/1080P120, U1 for other resolutions) into the designated slot. Ensure the card is inserted correctly to avoid data corruption.

Image: RunCam Hybrid 2 PCB Layout and Wiring Diagram.

പ്രവർത്തിക്കുന്നു

Once the camera is installed and powered, you can begin operation:

1. പവർ ഓൺ: Apply power to the camera. The FPV feed should appear on your goggles or monitor.
2. റെക്കോർഡിംഗ് നിയന്ത്രണം:
   • സ്വമേധയാലുള്ള നിയന്ത്രണം: Use the Power/Shutter Button on Side A of the PCB to start and stop HD recording.
   • UART Remote Control: If connected to a flight controller's UART, configure your Betaflight (or similar) settings to assign a switch on your radio to control recording start/stop.
3. മോഡ് സ്വിച്ചിംഗ്: Use the Mode Switch Button on Side A to cycle through different camera modes or settings if available.
4. QR Code Parameter Settings: For advanced configuration, download the RunCam app on your smartphone. Adjust desired settings within the app, generate a QR code, and then scan this QR code with the RunCam Hybrid 2 camera. The camera will automatically apply the new settings.

Image: QR Code Parameter Settings via RunCam App.

മെയിൻ്റനൻസ്

To ensure optimal performance and longevity of your RunCam Hybrid 2 camera, follow these maintenance guidelines:

• ലെൻസ് ക്ലീനിംഗ്: Regularly clean both the HD and FPV lenses with a soft, lint-free cloth and lens cleaning solution. Avoid abrasive materials that could scratch the lenses.
• വൈദ്യുതി വിതരണം: Always ensure the camera receives power within the specified DC 5-20V range. Incorrect voltage can cause irreversible damage.
• SD കാർഡ് മാനേജുമെന്റ്: നിങ്ങളുടെ റെക്കോർഡ് ചെയ്‌ത foo ഇടയ്ക്കിടെ ബാക്കപ്പ് ചെയ്യുകtage and format the Micro SD card to maintain optimal recording performance and prevent file corruption. Use a high-quality, recommended speed class SD card.
• ശാരീരിക പരിശോധന: Regularly check for any loose connections, damaged cables, or physical damage to the camera module.

ട്രബിൾഷൂട്ടിംഗ്

If you encounter issues with your RunCam Hybrid 2, refer to the following common problems and solutions:

• പവർ ഇല്ല/ക്യാമറ ഓണാക്കുന്നില്ല:
  • Check all power connections (VCC+, GND) for proper wiring and secure contact.
  • ഇൻപുട്ട് വോളിയം ആണെന്ന് പരിശോധിക്കുകtage is within the DC 5-20V range.
  • Ensure no short circuits are present in the wiring.
• No FPV Video Output:
  • Check the video signal cable connection from the camera to your VTX and from the VTX to your goggles/monitor.
  • Confirm that the TV mode (NTSC/PAL) setting on the camera matches your display device. This can be adjusted via QR code settings.
  • Ensure the VTX is powered and functioning correctly.
• Recording Errors / Corrupted Files:
  • മൈക്രോ എസ്ഡി കാർഡ് FAT32-ലേക്ക് ഫോർമാറ്റ് ചെയ്തിട്ടുണ്ടെന്ന് ഉറപ്പാക്കുക.
  • Use a high-speed Micro SD card (U3 or higher for 4K/high frame rate recording).
  • Try formatting the SD card again or using a different, known-good SD card.
  • Check the SD card slot for any debris or damage.
• QR Code Settings Not Applying:
  • Ensure the QR code is clearly visible and well-lit when scanning.
  • Hold the QR code steady in front of the camera lens until the settings are confirmed.
  • Verify that you are using the official RunCam app for generating QR codes.
• UART Control Not Working:
  • Check TX/RX wiring between the camera and the flight controller.
  • Verify UART settings in your flight controller firmware (e.g., Betaflight) are correctly configured for camera control.
  • Ensure the correct protocol is selected in the flight controller software.