ILIFE NOISZ S8 Pro Robot Vacuum and Mop Instruction Manual

1. ആമുഖം

This manual provides essential information for the safe and efficient operation of your ILIFE NOISZ S8 Pro Robot Vacuum and Mop. Please read it thoroughly before using the appliance and retain it for future reference.

2. ഉൽപ്പന്നം കഴിഞ്ഞുview

ഉൾപ്പെടുത്തിയ ഘടകങ്ങൾ

• ILIFE NOISZ S8 Pro Robot Vacuum and Mop Unit
• ചാർജിംഗ് ഡോക്ക്
• പവർ അഡാപ്റ്റർ
• സൈഡ് ബ്രഷുകൾ (2 ജോഡി)
• High-Performance Filters (2)
• Mop Pad (2)
• Water Tank (300 ml)
• ക്ലീനിംഗ് ടൂൾ
• ElectroWall (Virtual Barrier)

Figure 1: ILIFE NOISZ S8 Pro Robot Vacuum and Mop with its charging dock and a mop pad.

3. സജ്ജീകരണം

3.1 ചാർജിംഗ് ഡോക്ക് പ്ലേസ്മെന്റ്

Place the charging dock against a wall in an open, uncluttered area. Ensure there is at least 1 meter (3 feet) of clear space on both sides of the dock and 2 meters (6 feet) in front of it. Plug the power adapter into the charging dock and then into a wall outlet.

3.2 പ്രാരംഭ ചാർജിംഗ്

Place the robot onto the charging dock, ensuring the charging pins align. The robot will begin charging automatically. For first-time use, fully charge the robot for at least 5-6 hours.

3.3 Attaching Side Brushes

Press the side brushes onto the square posts on the bottom of the robot until they click into place. Ensure the 'L' and 'R' markings on the brushes match the corresponding markings on the robot.

3.4 Filling Water Tank (for Mopping)

Open the water tank cover, fill with clean water, and securely close the cover. Attach a clean mop pad to the bottom of the water tank. Slide the filled water tank into the slot at the rear of the robot until it clicks.

4. ഓപ്പറേഷൻ

4.1 വൃത്തിയാക്കൽ ആരംഭിക്കൽ/നിർത്തൽ

Press the 'CLEAN' button on the robot or use the remote control to start or pause cleaning. The robot will automatically begin cleaning in Auto mode.

4.2 ക്ലീനിംഗ് മോഡുകൾ

• യാന്ത്രിക മോഡ്: The robot cleans automatically using its gyroscope navigation to cover the entire area in a systematic, row-by-row pattern.
• സ്പോട്ട് മോഡ്: For concentrated cleaning of a specific dirty area, place the robot on the desired spot and select Spot mode. The robot will clean in a spiral pattern. The S8 Pro provides up to 2000Pa powerful suction in spot mode.
• എഡ്ജ് മോഡ്: റോബോട്ട് ചുവരുകളിലും ഫർണിച്ചറിന്റെ അരികുകളിലും വൃത്തിയാക്കുന്നു.
• മോപ്പിംഗ് മോഡ്: പരസ്യത്തോടൊപ്പം വാട്ടർ ടാങ്ക് ഘടിപ്പിക്കുകamp mop pad. The robot will vacuum and mop simultaneously. Water volume can be adjusted to adapt to different floor messes.

Figure 2: The robot utilizes gyroscope navigation for efficient, row-by-row cleaning.

4.3 Route Planning & Navigation

The S8 Pro uses gyroscope navigation to ensure maximum coverage and reduce missed areas. It follows a planned cleaning path for thorough cleaning.

4.4 ElectroWall (Virtual Barrier)

Use the ElectroWall device to create an invisible barrier that the robot will not cross. This helps to restrict the robot to specific areas or prevent it from entering unwanted zones.

4.5 Carpet Boost

The vacuum suction automatically boosts when the robot detects it is on a carpeted surface, providing enhanced cleaning power for medium-pile carpets. The underneath floating roller brush maintains close contact to lift stuck-in dirt. The robot can smoothly cross gaps within 15 mm, transitioning from hard floors to carpets.

Figure 3: The robot automatically boosts suction on carpets for effective cleaning.

5. പരിപാലനം

5.1 Emptying Dustbin

The cellular dustbin features a 4-layer filtration system. After each cleaning cycle, press the 'PUSH' button on the top cover to open it. Remove the dustbin and empty its contents. The dustbin has a capacity of 450ml.

Figure 4: The cellular dustbin's 4-layer filtration system captures fine dust.

5.2 ക്ലീനിംഗ് ഫിൽട്ടറുകൾ

Remove the high-performance filters from the dustbin. Tap them gently to remove dust. Do not wash the high-performance filters with water. Replace filters as needed to maintain optimal suction.

5.3 Cleaning Main Brush

Open the main brush cover on the bottom of the robot. Remove the main brush and use the cleaning tool to cut and remove any hair or debris tangled around it. Reinstall the main brush.

5.4 ക്ലീനിംഗ് സൈഡ് ബ്രഷുകൾ

Periodically check the side brushes for tangled hair or debris. Pull them off their posts and use the cleaning tool to remove any obstructions. Reattach them firmly.

5.5 Cleaning Water Tank/Mop Pad

After mopping, empty any remaining water from the tank. Remove the mop pad and wash it thoroughly. Allow both to air dry completely before reattaching or storing.

5.6 ക്ലീനിംഗ് സെൻസറുകൾ

Wipe the cliff sensors and charging contacts on the bottom of the robot with a clean, dry cloth to ensure proper function.

6. പ്രശ്‌നപരിഹാരം

If the robot encounters an issue, it may emit an audible alert or display an error code. Refer to the full user manual for a comprehensive list of error codes and troubleshooting steps. Common issues include:

• റോബോട്ട് ചാർജ് ചെയ്യുന്നില്ല: Ensure the charging dock is powered on and the robot's charging contacts are clean and aligned with the dock.
• റോബോട്ട് കുടുങ്ങിപ്പോകുന്നു: Clear obstacles from the cleaning path. Use ElectroWall to block off problematic areas.
• Reduced suction: Check and clean the dustbin and filters. Ensure the main brush and side brushes are free of tangles.
• Mopping issues: വാട്ടർ ടാങ്ക് നിറഞ്ഞിട്ടുണ്ടെന്നും മോപ്പ് പാഡ് വൃത്തിയുള്ളതും ശരിയായി ഘടിപ്പിച്ചിട്ടുണ്ടെന്നും ഉറപ്പാക്കുക.

7 സ്പെസിഫിക്കേഷനുകൾ

8. വാറൻ്റിയും പിന്തുണയും

The ILIFE NOISZ S8 Pro comes with a 1-year limited warranty from the date of purchase. For warranty claims, technical support, or service inquiries, please refer to the contact information provided in your full user manual or visit the official ILIFE webസൈറ്റ്.