Roco RQ-W1LT1700 HB Mechanical Pencil User Manual

1. ആമുഖം

Thank you for choosing the Roco RQ-W1LT1700 HB Mechanical Pencil set. This set includes four 0.5 mm mechanical pencils designed for smooth and consistent writing and drawing. This manual provides essential information on how to set up, operate, maintain, and troubleshoot your mechanical pencils to ensure optimal performance and longevity.

ചിത്രം 1: മുൻഭാഗം view of the Roco RQ-W1LT1700 HB Mechanical Pencil 4-Pieces package, showing four pencils in various colors.

2. സജ്ജീകരണം

Your Roco mechanical pencils come pre-loaded with HB lead. To load or replace lead:

1. Locate the eraser at the top of the pencil.
2. Gently pull the eraser and the attached mechanism straight out from the pencil body. This will reveal the lead reservoir.
3. Insert new 0.5 mm lead sticks into the reservoir. Do not overfill; typically, 2-3 lead sticks are sufficient.
4. Carefully push the eraser and mechanism back into the pencil body until it is securely seated.

Figure 2: Back of the product packaging illustrating the "PULL OUT" and "PUSH IN" steps for lead replacement.

3. പ്രവർത്തന നിർദ്ദേശങ്ങൾ

Using your Roco mechanical pencil is straightforward:

• To extend the lead, press the top button (where the eraser is located) repeatedly until the desired lead length is exposed.
• To retract the lead, press and hold the top button, then gently push the lead back into the tip.
• The eraser can be used by removing the cap or by simply using the exposed part.

4. പരിപാലനം

Proper maintenance ensures the longevity and smooth operation of your mechanical pencils:

• നുറുങ്ങ് വൃത്തിയാക്കൽ: If lead dust accumulates in the tip, gently remove it using a soft brush or a piece of cloth. Avoid using sharp objects that could damage the mechanism.
• ലെഡ് സംഭരണം: Store extra lead in a secure container to prevent breakage.
• തുള്ളികൾ ഒഴിവാക്കുക: Dropping the pencil, especially on its tip, can damage the internal mechanism or bend the lead sleeve, leading to lead breakage or jamming.
• ഇറേസർ മാറ്റിസ്ഥാപിക്കൽ: When the eraser wears down, it can be replaced by pulling out the old one and inserting a new compatible eraser.

5. പ്രശ്‌നപരിഹാരം

നിങ്ങൾ നേരിട്ടേക്കാവുന്ന പൊതുവായ പ്രശ്നങ്ങൾക്കുള്ള പരിഹാരങ്ങൾ ഇതാ:

• Lead Not Advancing:
  • Check if the lead reservoir is empty. Load new lead if necessary.
  • Ensure the lead is the correct 0.5 mm diameter. Incorrect lead size can cause jamming.
  • Inspect the tip for broken lead pieces or debris. Clear any obstructions carefully.
• Lead Breaking Frequently:
  • Avoid extending too much lead at once. A short extension provides better support.
  • Apply less pressure when writing.
  • Ensure you are using good quality 0.5 mm HB lead.
• Eraser Not Staying In:
  • Ensure the eraser is fully pushed into the mechanism.
  • If the eraser is old or worn, it might have shrunk. Replace it with a new one.

6 സ്പെസിഫിക്കേഷനുകൾ

7. വാറൻ്റിയും പിന്തുണയും

Roco mechanical pencils are manufactured to high-quality standards. While specific warranty details are not provided in this manual, please retain your proof of purchase for any potential warranty claims. For product support or inquiries, please refer to the retailer where the product was purchased or visit the official Roco webബന്ധപ്പെടാനുള്ള വിവരങ്ങൾക്കുള്ള സൈറ്റ്.

For general information about Roco products, you may visit: www.roco.com (കുറിപ്പ്: ഇതൊരു പ്ലെയ്‌സ്‌ഹോൾഡറാണ് URL (ഉൽപ്പന്ന ഡാറ്റയിൽ പ്രത്യേക പിന്തുണാ ലിങ്ക് നൽകിയിട്ടില്ലാത്തതിനാൽ.)