പോളിവൻസ് 3701-4 ബമ്പർ & ക്ലാഡിംഗ് കളർ കോട്ട് യൂസർ മാനുവൽ
മോഡൽ: 3701-4
1. ഉൽപ്പന്നം കഴിഞ്ഞുview
The Polyvance Bumper & Cladding Color Coat (Model 3701-4) is an advanced, low-VOC, solvent-based coating specifically formulated to permanently recolor molded-in-color textured TPO and polypropylene plastic components. This includes bumpers, side cladding, and trim found on various vehicles.
Unlike temporary silicone-based products, this color coat adheres strongly to the plastic surface, providing a durable and lasting finish that resists fading, marring, and staining. It is designed for direct application without the need for adhesion promoters or extensive sanding on compatible plastic types.
Image 1.1: Polyvance 3701-4 Bumper & Cladding Color Coat in a quart can, showing product labeling and key features.
പ്രധാന സവിശേഷതകൾ:
- Permanently recolors faded, scuffed, marred, discolored, or damaged plastic bumpers, side cladding, and trim.
- Adheres to TPO and Polypropylene (PP) plastic without sanding, adhesion promoter, or primer.
- Forms a strong, durable bond that resists removal by pressure washing.
- Low VOC (Volatile Organic Compound) formula.
2 സുരക്ഷാ വിവരങ്ങൾ
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
DANGER: FLAMMABLE. HARMFUL OR FATAL IF SWALLOWED. READ CAUTIONS ON BACK PANEL.
Always read and understand the Safety Data Sheet (SDS) for this product before use. The SDS provides detailed information on hazards, safe handling, and emergency procedures.
പൊതു സുരക്ഷാ മുൻകരുതലുകൾ:
- വെൻ്റിലേഷൻ: Use in a well-ventilated area or outdoors. Avoid breathing vapors.
- വ്യക്തിഗത സംരക്ഷണ ഉപകരണങ്ങൾ (PPE): Wear appropriate PPE, including chemical-resistant gloves, eye protection (safety goggles), and a respirator suitable for organic vapors.
- ജ്വലനം: ചൂട്, തീപ്പൊരി, തുറന്ന തീജ്വാലകൾ, ചൂടുള്ള പ്രതലങ്ങൾ എന്നിവയിൽ നിന്ന് അകറ്റി നിർത്തുക. പുകവലി പാടില്ല.
- സംഭരണം: Store in a cool, dry, well-ventilated place, away from incompatible materials and direct sunlight. Keep container tightly closed.
- നീക്കം ചെയ്യൽ: പ്രാദേശിക, പ്രാദേശിക, ദേശീയ, അന്തർദേശീയ നിയന്ത്രണങ്ങൾക്കനുസൃതമായി ഉള്ളടക്കങ്ങളും കണ്ടെയ്നറും വിനിയോഗിക്കുക.
- പ്രഥമ ശ്രുശ്രൂഷ: In case of contact with skin or eyes, rinse immediately with plenty of water. If swallowed, do NOT induce vomiting. Call a Poison Control Center or doctor immediately.
3. തയ്യാറാക്കലും സജ്ജീകരണവും
Proper preparation of the surface is crucial for optimal adhesion and finish quality, even though sanding and adhesion promoters are not required for compatible plastics.
ഉപരിതല അനുയോജ്യത:
- ശുപാർശ ചെയ്യുന്നത്: Molded-in-color textured TPO (Thermoplastic Olefin) and polypropylene (PP) plastic bumpers, side cladding, and trim.
- Not Recommended Without Sanding: Raw polyurethane (PUR) or OEM primed bumpers. These substrates require proper sanding and preparation before application.
തയ്യാറെടുപ്പ് ഘട്ടങ്ങൾ:
- ഉപരിതലം വൃത്തിയാക്കുക: Thoroughly clean the plastic surface to be coated. Use a suitable automotive cleaner or degreaser to remove all dirt, grease, wax, silicone, and other contaminants. Rinse thoroughly with water and allow to dry completely. Any residue will compromise adhesion.
- മാസ്കിംഗ്: Mask off any areas not intended for coating, such as painted body panels, chrome trim, or adjacent components, using automotive masking tape and paper/plastic sheeting.
- താപനിലയും ഈർപ്പവും: Ensure the application area is within recommended temperature and humidity ranges (refer to product label for specifics, typically room temperature and moderate humidity).
- നന്നായി കുലുക്കുക: Before opening, shake the can vigorously for at least 2-3 minutes to ensure the color coat is thoroughly mixed. Continue to shake periodically during application.
4. Application Instructions (Operating)
Follow these steps for effective application of the Polyvance Bumper & Cladding Color Coat:
- Ventilation and PPE: Ensure adequate ventilation and wear all recommended personal protective equipment (gloves, eye protection, respirator).
- ടെസ്റ്റ് ഏരിയ: If possible, test the color coat on an inconspicuous area or a scrap piece of the same plastic to verify color match and adhesion.
- അപേക്ഷാ രീതി: This product is typically applied using a spray gun. Consult the product label for specific nozzle and pressure recommendations. Apply in thin, even coats.
- ആദ്യ കോട്ട്: Apply a light, even mist coat to the prepared surface. This initial coat helps promote adhesion and provides a base for subsequent coats.
- Subsequent Coats: Allow appropriate flash-off time between coats (refer to product label, typically 5-10 minutes). Apply additional thin, even coats until desired coverage and color uniformity are achieved. Avoid applying excessively thick coats, which can lead to runs or uneven drying.
- ഉണക്കൽ സമയം: Allow the coated surface to dry completely before handling or exposing to moisture. Drying times will vary based on temperature, humidity, and film thickness. Refer to the product label for specific recoat and full cure times.
- ക്ലീനപ്പ്: Clean spray equipment immediately after use with appropriate solvent.
5. പരിപാലനം
Once cured, the Polyvance Bumper & Cladding Color Coat provides a durable and permanent finish. Maintenance is straightforward:
- വൃത്തിയാക്കൽ: Clean the coated surface with standard automotive car wash soap and water. Avoid harsh abrasive cleaners or strong solvents, which could potentially damage the finish over time.
- സംരക്ഷണം: While the coating is highly durable, regular waxing or application of a UV protectant designed for automotive plastics can help extend its lifespan and maintain its appearance, especially in harsh environmental conditions.
- കേടുപാടുകൾ തീർക്കൽ: In case of new damage (scratches, scuffs) to the coated area, the product can be reapplied to the affected section after proper cleaning and preparation.
6. പ്രശ്നപരിഹാരം
This section addresses common issues that may arise during or after application.
| പ്രശ്നം | സാധ്യമായ കാരണം | പരിഹാരം |
|---|---|---|
| Product clumping or poor consistency | Expired product, improper storage (e.g., extreme temperatures), or insufficient mixing. | Check the manufacturing or expiration date on the can. Ensure product is stored in a cool, dry place. Shake vigorously before and during use. If product is expired or consistency is poor despite mixing, do not use. |
| Poor adhesion or peeling | Inadequate surface cleaning (presence of grease, wax, silicone), incompatible substrate (e.g., raw PUR without sanding), or application in unsuitable environmental conditions. | Ensure surface is meticulously clean and dry. Verify substrate compatibility. Apply within recommended temperature and humidity ranges. Re-prepare and reapply. |
| Uneven finish or runs | Applying coats too thick, insufficient flash-off time between coats, or improper spray technique. | Apply multiple thin, even coats. Allow adequate flash-off time between coats. Maintain consistent spray distance and speed. |
| Color not matching expectation | Variations in base plastic color, lighting conditions, or product batch. | Always perform a test application on an inconspicuous area first. Ensure consistent application technique. |
7 സ്പെസിഫിക്കേഷനുകൾ
| ഉൽപ്പന്നത്തിൻ്റെ പേര് | Bumper & Cladding Color Coat |
| മോഡൽ നമ്പർ | 3701-4 |
| ബ്രാൻഡ് | പോളിവാൻസ് |
| നിർമ്മാതാവ് | പോളിവാൻസ് |
| നിറം | കറുപ്പ് |
| വോളിയം | 1 ക്വാർട്ട് (945 മില്ലി) |
| ഇനത്തിൻ്റെ ഭാരം | 2.25 പൗണ്ട് |
| ഉൽപ്പന്ന അളവുകൾ | 3.38 x 3.38 x 8.75 ഇഞ്ച് |
| ഉപരിതല ശുപാർശ | Plastic (TPO, Polypropylene) |
| ഫിറ്റ് തരം | വാഹനത്തിൻ്റെ പ്രത്യേക ഫിറ്റ് |
| യു.പി.സി | 694687002688 |
8. വാറൻ്റിയും പിന്തുണയും
Polyvance is committed to providing high-quality plastic repair products and expertise. While specific warranty details for the 3701-4 Bumper & Cladding Color Coat are not provided in this manual, customers are encouraged to contact Polyvance directly for any warranty-related inquiries or product support.
Polyvance has been assisting with plastic repairs since 1981 and focuses exclusively on products that aid in repairing or refinishing broken plastic. For technical assistance, application advice, or to report product issues, please refer to the contact information provided on the product packaging or the official Polyvance webസൈറ്റ്.
For more information about Polyvance and their commitment to quality, visit their official webസൈറ്റ് അല്ലെങ്കിൽ അവരുടെ ഉപഭോക്തൃ സേവന വിഭാഗവുമായി ബന്ധപ്പെടുക.
