1. ആമുഖം
This manual provides comprehensive instructions for the QIACHIP EV1527 Rf433m Wireless Remote Transmitters. These transmitters are designed to be used with a compatible 12V 1-channel wireless receiver (receiver not included) to control various electronic devices remotely. Please read this manual carefully before use to ensure proper setup and operation.
Image 1.1: Three QIACHIP EV1527 Rf433m Wireless Remote Transmitters. Each remote features two buttons, labeled 'A' and 'B', and an attached metal keychain clip.
2. ഉൽപ്പന്നം കഴിഞ്ഞുview
The QIACHIP EV1527 Rf433m Wireless Remote Transmitter is a compact and ergonomic device designed for convenient remote control. Each remote features two silicone buttons and an indicator light.
2.1 ഘടകങ്ങൾ
- Silicone Buttons (A and B): Used to send control signals to the paired receiver.
- ഇൻഡിക്കേറ്റർ ലൈറ്റ്: Illuminates when a button is pressed, indicating signal transmission.
- Chrome Bezel: Provides a durable and aesthetic finish.
- Metal Keychain: Allows for easy attachment to keys or other items.
Image 2.1: Diagram illustrating the key components of the remote control, including the silicone buttons (A and B), indicator light, chrome bezel, and metal keychain.
2.2 പ്രവർത്തന ശ്രേണി
These remote transmitters offer a wide operating range, typically up to 100 meters in an open, unobstructed area. Actual range may vary depending on environmental factors and obstacles.
Image 2.2: Illustration depicting the effective operating range of the wireless remote, showing a signal reaching up to 100 meters in an open environment.
3. സജ്ജീകരണം
3.1 ബാറ്ററി ഇൻസ്റ്റാളേഷൻ
The remote control requires one CR2032 button cell battery. The battery is typically pre-installed, but if replacement is needed or if the remote is not functioning, follow these steps:
- റിമോട്ട് സി ശ്രദ്ധാപൂർവ്വം തുറക്കുകasing. This usually involves prying apart the two halves of the remote, often near the keychain loop.
- Locate the battery compartment on the circuit board.
- പഴയ CR2032 ബാറ്ററി നീക്കം ചെയ്യുക, അതിന്റെ പോളാരിറ്റി ശ്രദ്ധിക്കുക.
- പോസിറ്റീവ് (+) വശം മുകളിലേക്ക് അഭിമുഖീകരിക്കുന്ന ഒരു പുതിയ CR2032 ബാറ്ററി ഇടുക.
- റിമോട്ട് സി അടയ്ക്കുകasinഗ്രാം സുരക്ഷിതമായി.
ചിത്രം 3.1: View of the remote's internal circuit board, showing the placement of the CR2032 button cell battery.
3.2 ഒരു റിസീവറുമായി ജോടിയാക്കൽ
These transmitters are designed to work with a compatible QIACHIP 12V 1-channel wireless receiver (not included). A single receiver can pair with up to 20 remotes. The pairing process typically involves the following steps, though specific details may vary based on your receiver model:
- പവർ ഓൺ റിസീവർ: Ensure your 12V 1-channel wireless receiver is powered on.
- Clear Existing Programming (Recommended): To prevent conflicts, it is often recommended to clear any previous pairings on the receiver. This is typically done by pressing the receiver's learning button (often a small button on the circuit board) 8 times. The receiver's indicator light should flash rapidly and then turn off, confirming the memory has been cleared.
- പഠന മോഡ് നൽകുക: Press the receiver's learning button once or twice, depending on the desired operating mode (e.g., momentary, toggle, latched). The receiver's indicator light will illuminate steadily, indicating it is in learning mode.
- സിഗ്നൽ പ്രക്ഷേപണം ചെയ്യുക: While the receiver's indicator light is steady, press the desired button (A or B) on your QIACHIP remote transmitter. The remote's indicator light will flash.
- ജോടിയാക്കൽ സ്ഥിരീകരിക്കുക: The receiver's indicator light should flash a few times and then turn off, confirming successful pairing.
- ടെസ്റ്റ് പ്രവർത്തനം: Press the paired button on the remote to ensure the receiver responds as expected.
കുറിപ്പ്: Refer to your specific receiver's instruction manual for precise pairing procedures and mode selection (e.g., momentary, toggle, latched).
4. പ്രവർത്തിക്കുന്നു
Once your QIACHIP EV1527 remote transmitter is successfully paired with a compatible receiver, operation is straightforward:
- Press Button A or B: Simply press the 'A' or 'B' button on the remote to send a signal to the receiver.
- ഇൻഡിക്കേറ്റർ ലൈറ്റ്: The small indicator light on the remote will illuminate briefly when a button is pressed, confirming that a signal is being transmitted.
- Receiver Response: The paired receiver will execute the programmed action (e.g., turn a device on/off, open/close a garage door) according to its configured mode (momentary, toggle, or latched).
5. പരിപാലനം
5.1 ബാറ്ററി മാറ്റിസ്ഥാപിക്കൽ
If the remote's indicator light becomes dim or fails to illuminate, or if the remote's range decreases significantly, it may be time to replace the battery. The remote uses one CR2032 button cell battery.
- Open the remote casing as described in Section 3.1.
- പഴയ CR2032 ബാറ്ററി ശ്രദ്ധാപൂർവ്വം നീക്കം ചെയ്യുക.
- Insert a new CR2032 battery, ensuring the positive (+) side is facing up.
- റിമോട്ട് സി അടയ്ക്കുകasinഗ്രാം സുരക്ഷിതമായി.
കുറിപ്പ്: In some rare cases, after battery replacement, the remote may need to be re-paired with the receiver. Follow the pairing instructions in Section 3.2 if necessary.
6. പ്രശ്നപരിഹാരം
- റിമോട്ട് പ്രതികരിക്കുന്നില്ല:
- Check the battery: Ensure the CR2032 battery is correctly installed and has sufficient charge. Try replacing it with a new battery.
- Receiver Power: Verify that your 12V 1-channel wireless receiver is properly powered and functioning.
- Re-pairing: Attempt to re-pair the remote with the receiver following the steps in Section 3.2.
- Remote Reset: If a new remote or a remote after battery change is not pairing, try removing and reinserting the battery in the remote to perform a soft reset, then attempt pairing again.
- പരിമിതമായ പ്രവർത്തന ശ്രേണി:
- Obstructions: Ensure there are no significant physical obstructions (e.g., thick walls, metal objects) between the remote and the receiver.
- Antenna: Verify that the receiver's antenna (if applicable) is fully extended and unobstructed.
- Interference: Minimize potential sources of radio frequency interference in the vicinity.
7 സ്പെസിഫിക്കേഷനുകൾ
| ഫീച്ചർ | വിശദാംശങ്ങൾ |
|---|---|
| മോഡൽ നമ്പർ | KT05-AB-3 |
| ബ്രാൻഡ് | QIACHIP |
| ആവൃത്തി | 433MHz (Rf433m) |
| Encoding Chip | EV1527 |
| ബാറ്ററി തരം | 1 x CR2032 (ആവശ്യമാണ്) |
| Max Supported Remotes (per receiver) | 20 വരെ |
| പ്രവർത്തന ശ്രേണി | 100 മീറ്റർ വരെ (തുറന്ന പ്രദേശം) |
| അനുയോജ്യമായ ഉപകരണങ്ങൾ | 12V 1-channel wireless receivers, Garage Door systems |
| പാക്കേജ് അളവുകൾ | 5.35 x 4.96 x 1.06 ഇഞ്ച് |
| ഇനത്തിൻ്റെ ഭാരം | 3.53 ഔൺസ് |
Image 7.1: Diagram showing the approximate dimensions of the remote control: 6.1 cm in length and 2.9 cm in width.
8. വാറൻ്റിയും പിന്തുണയും
8.1 വാറൻ്റി വിവരങ്ങൾ
Specific warranty details for the QIACHIP EV1527 Rf433m Wireless Remote Transmitters are not provided in the product documentation. For information regarding warranty coverage, please contact the seller or manufacturer directly.
8.2 ഉപഭോക്തൃ പിന്തുണ
For further assistance, technical support, or inquiries, please contact QIACHIP customer service through their official channels or the retailer where the product was purchased.
You can visit the QIACHIP Store for more information: QIACHIP Store on Amazon
