1. ആമുഖം
This manual provides essential information for the proper setup, operation, and maintenance of your LDARC X-BOSS FM900 2.4GHz FASST Receiver. Please read this manual thoroughly before using the product to ensure safe and efficient operation.
2. ഉൽപ്പന്നം കഴിഞ്ഞുview
Image: The LDARC X-BOSS FM900 receiver, a compact circuit board featuring surface-mount components, an integrated antenna, and clearly labeled 'FM900' branding. This image illustrates the physical design and component layout of the receiver.
3. സവിശേഷതകൾ
- Offers great reliability, stable signal link, precision antenna, and high sensitivity.
- Compact and lightweight design for various applications.
- Integrated LNA (Low Noise Amplifier) for enhanced signal reception.
- RSSI (Received Signal Strength Indicator) output for real-time signal monitoring.
4 സ്പെസിഫിക്കേഷനുകൾ
| സ്പെസിഫിക്കേഷൻ | വിശദാംശങ്ങൾ |
|---|---|
| ഇനം | FM900 Receiver |
| ഭാരം | 1.2 ഗ്രാം |
| അളവുകൾ | 11.5 മിമി x 21 മിമി |
| വാല്യംtage | 4-6V |
| പ്രവർത്തന ശ്രേണി | >900m (air distance without electromagnetic interference) |
| പ്രോട്ടോക്കോൾ | ഫാസ്റ്റ് |
| Put ട്ട്പുട്ട് 1 | LNA |
| Put ട്ട്പുട്ട് 2 | ആർഎസ്എസ്ഐ |
| പിന്തുണയ്ക്കുന്ന ട്രാൻസ്മിറ്ററുകൾ | T8FG, T14SG, T16SZ, T18SZ, T18MZ, T32MZ TX |
| Real-Time RSSI Compatibility | F3, F4, F7, etc. flight controllers |
5. പാക്കേജ് ഉള്ളടക്കം
- 1x LDARC X-BOSS FM900 Receiver
6. സജ്ജീകരണം
6.1. ഇൻസ്റ്റലേഷൻ
Carefully connect the receiver to your flight controller or power source, ensuring correct polarity and signal connections. Mount the receiver securely in your model, away from sources of electrical interference. Position the antenna for optimal signal reception, avoiding obstructions.
6.2. ബൈൻഡിംഗ് നടപടിക്രമം
To establish communication between your transmitter and the FM900 receiver, follow these general binding steps:
- Power on your transmitter and select the FASST protocol.
- Place your transmitter in binding mode (refer to your transmitter's manual for specific instructions).
- Apply power to the FM900 receiver. The receiver's LED indicator should begin to flash, indicating it is ready for binding.
- Once the binding process is complete, the receiver's LED will typically turn solid green, indicating a successful connection.
- Power cycle both the transmitter and receiver to confirm the binding is retained.
7. പ്രവർത്തന നിർദ്ദേശങ്ങൾ
After successful binding and installation, ensure your transmitter and receiver are powered on before operating your model. Always perform a range check and verify all control surfaces respond correctly before flight. Monitor the RSSI output on your flight controller or OSD (On-Screen Display) to ensure a strong signal link during operation.
8. പരിപാലനം
- റിസീവർ വൃത്തിയായും പൊടി, അഴുക്ക്, ഈർപ്പം എന്നിവയിൽ നിന്ന് മുക്തമായും സൂക്ഷിക്കുക.
- Regularly inspect antenna connections for damage or loose contacts.
- റിസീവറിനെ തീവ്രമായ താപനിലയിലോ നേരിട്ടുള്ള സൂര്യപ്രകാശത്തിലോ ദീർഘനേരം തുറന്നുകാട്ടുന്നത് ഒഴിവാക്കുക.
- Ensure proper ventilation around the receiver during operation.
9. പ്രശ്നപരിഹാരം
- No Signal/Loss of Link: Re-check binding procedure. Ensure transmitter and receiver are powered on. Verify antenna connection and placement. Check for potential interference sources.
- ഇടവിട്ടുള്ള സിഗ്നൽ: Inspect antenna for damage. Ensure receiver is not too close to high-current wires or other electronic components that may cause interference.
- Receiver Not Powering On: പവർ കണക്ഷനുകളും വോള്യവും പരിശോധിക്കുകtage supply (4-6V). Check for shorts or incorrect wiring.
- തെറ്റായ നിയന്ത്രണ പ്രതികരണം: Confirm correct channel mapping in your flight controller or model setup. Re-bind the receiver if necessary.
10. വാറന്റി, പിന്തുണ വിവരങ്ങൾ
LDARC products are manufactured to high-quality standards. For specific warranty terms and conditions, please refer to the documentation provided at the time of purchase or contact your retailer. For technical support, please reach out to your authorized LDARC dealer or visit the official LDARC webസഹായത്തിനുള്ള സൈറ്റ്.
