ആമുഖം
This manual provides essential instructions for the safe and effective use of your NERF Pro Gelfire Raid Blaster. Please read all instructions carefully before operating the blaster. This product is designed for users aged 14 and up.
സുരക്ഷാ വിവരങ്ങൾ
മുന്നറിയിപ്പ്: ചെറിയ ഭാഗങ്ങൾ സൃഷ്ടിക്കപ്പെട്ടേക്കാം. 3 വയസ്സിന് താഴെയുള്ള കുട്ടികൾക്ക് വേണ്ട.
- Always wear the included protective eyewear when using this blaster.
- കണ്ണും മുഖവും ലക്ഷ്യമാക്കരുത്.
- Use only official NERF Pro Gelfire rounds. Other projectiles may not meet safety standards.
- Do not modify the blaster or gel rounds.
- Outdoor use is recommended.
ബോക്സിൽ എന്താണുള്ളത്
- NERF Pro Gelfire Raid Blaster
- 10,000 Dehydrated NERF Pro Gelfire Soft Super Absorbent Polymer Projectiles
- 800-Round Capacity Hopper
- സംരക്ഷണ കണ്ണട
- നിർദ്ദേശ മാനുവൽ (ഈ പ്രമാണം)
Image: The NERF Pro Gelfire Raid Blaster, showing the blaster, two packets of dehydrated gel rounds, protective eyewear, and a visual representation of 10,000 gel rounds.
സജ്ജമാക്കുക
1. Hydrating Gel Rounds
- Empty the dehydrated gel rounds into a large container.
- Add a sufficient amount of water to fully submerge the rounds.
- Allow the rounds to soak for at least 3-4 hours, or until they have expanded to their full size (approximately 7-8mm).
- Drain any excess water before use. Store hydrated rounds in an airtight container away from direct sunlight.
Image: Illustration showing small dehydrated gel rounds transforming into larger, hydrated gel rounds after adding water.
2. Loading the Hopper
- Ensure gel rounds are fully hydrated and drained of excess water.
- Open the lid of the 800-round capacity hopper.
- Carefully pour the hydrated gel rounds into the hopper. Do not overfill.
- Securely close the hopper lid.
Image: A hand holding the clear, orange-filled 800-round capacity hopper, ready for attachment to the blaster.
3. Attaching the Hopper
- Locate the hopper attachment point on top of the blaster.
- Align the hopper with the attachment point and firmly press it into place until it clicks securely.
ഓപ്പറേഷൻ
1. Engaging the Trigger Lock
- Before handling, ensure the trigger lock is engaged to prevent accidental firing. The trigger lock is typically a switch located near the trigger.
Image: A user wearing protective eyewear, demonstrating the location of the trigger lock on the blaster.
2. Priming the Blaster
- ട്രിഗർ ലോക്ക് വിച്ഛേദിക്കുക.
- Grip the pump-action handle located under the barrel.
- Pull the handle fully backward, then push it fully forward until it locks into place. This action primes the blaster and loads gel rounds into the firing mechanism.
Image: A user demonstrating the pump-action motion required to prime the blaster, indicated by white arrows.
3. ഫയറിംഗ്
- Once primed, aim the blaster at a safe target.
- Pull the trigger to fire. The Raid Blaster features scattershot blasting, firing 5 rounds with each trigger pull.
ചിത്രം: ഒരു ക്ലോസ്-അപ്പ് view of the blaster's muzzle, showing five gel rounds being fired simultaneously.
Image: A user aiming the blaster, highlighting its capability to fire rounds at up to 150 feet per second (FPS).
മെയിൻ്റനൻസ്
വൃത്തിയാക്കൽ
- After each use, wipe down the exterior of the blaster with a clean, damp തുണി.
- Ensure no gel rounds or debris are lodged in the firing mechanism or hopper.
- Do not submerge the blaster in water.
സംഭരണം
- Store the blaster in a cool, dry place away from direct sunlight.
- Remove any remaining hydrated gel rounds from the hopper before storing for extended periods.
- Engage the trigger lock when storing the blaster.
ട്രബിൾഷൂട്ടിംഗ്
- Blaster not firing:
a. Check if the trigger lock is disengaged.
b. Ensure the blaster is fully primed by pulling the pump-action handle completely back and then forward.
c. Verify that the hopper contains hydrated gel rounds and is securely attached. - Gel rounds not feeding properly:
a. Ensure gel rounds are fully hydrated and not too small or too large. Improperly hydrated rounds can cause feeding issues.
b. Check for any obstructions in the hopper or feeding mechanism. - Reduced firing velocity:
a. Ensure the blaster is properly primed with a full pump-action cycle.
b. Use only official NERF Pro Gelfire rounds.
സ്പെസിഫിക്കേഷനുകൾ
| മോഡൽ നമ്പർ | F7634 |
| ഉൽപ്പന്ന അളവുകൾ | 24 x 2.63 x 9 ഇഞ്ച് |
| ഇനത്തിൻ്റെ ഭാരം | 1.75 പൗണ്ട് |
| ശുപാർശ ചെയ്യുന്ന പ്രായം | 14 വർഷവും അതിൽ കൂടുതലും |
| ഹോപ്പർ കപ്പാസിറ്റി | 800 റൗണ്ടുകൾ |
| Projectile Type | Hydrated Gel Rounds |
| നിർമ്മാതാവ് | ഹസ്ബ്രോ |
വാറൻ്റിയും പിന്തുണയും
For warranty information, product support, or to purchase additional gel rounds and accessories, please visit the official Nerf website or contact Hasbro customer service. Keep your proof of purchase for any warranty claims.
Nerf Official Webസൈറ്റ്: www.hasbro.com/en-us/brands/nerf
