FUTABA MEGATECH 3PM-2.4G 2.4GHz-SS സിസ്റ്റം യൂസർ മാനുവൽ

ആമുഖം

This manual provides comprehensive instructions for the safe and effective operation, setup, and maintenance of your FUTABA MEGATECH 3PM-2.4G 2.4GHz-SS radio control system. Please read this manual thoroughly before using the product to ensure proper function and to prevent damage or injury.

ഉൽപ്പന്നം കഴിഞ്ഞുview

The FUTABA MEGATECH 3PM-2.4G is a high-performance 2.4GHz-SS radio control system designed for various remote-controlled applications. It includes a transmitter, receiver, and other essential components for precise control.

സിസ്റ്റം ഘടകങ്ങൾ

The system typically includes:

• Transmitter (T3PM): The handheld unit used to send control signals.
• Receiver (R603FS): The unit installed in your model that receives signals from the transmitter.
• ഇലക്ട്രോണിക് സ്പീഡ് കണ്ട്രോളർ (ESC): Manages motor speed and direction.
• സെർവോ: Converts electrical signals into mechanical motion for steering or other functions.

ട്രാൻസ്മിറ്റർ വിശദാംശങ്ങൾ

സജ്ജമാക്കുക

1. ട്രാൻസ്മിറ്റർ ബാറ്ററി ഇൻസ്റ്റാളേഷൻ

The T3PM transmitter requires 8 AA batteries (not included) for operation. Ensure batteries are inserted with correct polarity.

1. Open the battery compartment cover on the back of the transmitter (refer to Figure 3).
2. Insert 8 AA batteries, paying close attention to the positive (+) and negative (-) markings inside the compartment.
3. ബാറ്ററി കമ്പാർട്ട്മെൻ്റ് കവർ സുരക്ഷിതമായി അടയ്ക്കുക.

Note: The display will show the current battery voltage. A reading of 9.4V indicates fully charged batteries.

2. Receiver and Servo Connection

Connect the receiver and servo to your model's electronic components. Refer to your model's specific instructions for mounting and wiring.

• Connect the servo to the appropriate channel on the receiver (e.g., Channel 1 for steering).
• Connect the Electronic Speed Controller (ESC) to the receiver's throttle channel (e.g., Channel 2).
• Ensure all connections are secure and correctly oriented.

3. ട്രാൻസ്മിറ്ററും റിസീവറും ബന്ധിപ്പിക്കൽ

The transmitter and receiver must be "bound" to each other to establish a secure communication link. Refer to the detailed binding procedure in the full manual for your specific receiver model (e.g., R603FS).

പ്രവർത്തന നിർദ്ദേശങ്ങൾ

1. പവർ ചെയ്യുന്നു

• ആദ്യം ട്രാൻസ്മിറ്റർ ഓണാക്കുക.
• Then, turn on the receiver/model power switch.

2. അടിസ്ഥാന നിയന്ത്രണങ്ങൾ

• സ്റ്റിയറിംഗ് വീൽ: Rotate left or right to control the steering of your model.
• ത്രോട്ടിൽ ട്രിഗർ: Pull to accelerate forward, push to brake or reverse.
• ഡിസ്പ്ലേയും ബട്ടണുകളും: Use the display and associated buttons (SEL, CH) to navigate menus and adjust settings such as trim, servo reverse, and endpoint adjustments.

3. പവർ ഓഫ്

• Turn off the receiver/model power switch first.
• Then, turn off the transmitter.

Important: Always turn on the transmitter before the receiver and turn off the receiver before the transmitter to prevent loss of control.

മെയിൻ്റനൻസ്

• വൃത്തിയാക്കൽ: Wipe the transmitter and receiver with a soft, dry cloth. Do not use solvents or abrasive cleaners.
• സംഭരണം: Store the system in a cool, dry place away from direct sunlight and extreme temperatures. Remove batteries from the transmitter if storing for extended periods.
• ബാറ്ററി കെയർ: Use high-quality batteries. If using rechargeable batteries, follow the manufacturer's charging instructions.
• ആൻ്റിന കെയർ: Ensure the transmitter antenna is not bent or damaged. The receiver antenna should be routed correctly within your model to maximize range.

ട്രബിൾഷൂട്ടിംഗ്

സ്പെസിഫിക്കേഷനുകൾ

വാറൻ്റിയും പിന്തുണയും

For warranty information and technical support, please refer to the official FUTABA website or contact your authorized dealer. Keep your proof of purchase for any warranty claims.

For further assistance, you may also refer to the manufacturer reference: oku-q1080293591.