ENDORFY Navis F360 ARGB AIO CPU Water Cooler User Manual

ആമുഖം

This user manual provides comprehensive instructions for the installation, operation, and maintenance of your ENDORFY Navis F360 ARGB All-in-One (AIO) CPU Water Cooler. Designed for high-performance cooling, this system features a 360mm radiator, a PWM-controlled pump, and three Fluctus 120 PWM ARGB fans to ensure optimal thermal management for your CPU.

ഉൽപ്പന്നം കഴിഞ്ഞുview

The ENDORFY Navis F360 ARGB is an advanced liquid cooling solution for modern computer systems. It consists of a radiator, a pump/cold plate assembly, and three 120mm fans, all integrated with Addressable RGB (ARGB) lighting for customizable aesthetics.

ചിത്രം 1: The ENDORFY Navis F360 ARGB AIO CPU Water Cooler, showing the 360mm radiator with three fans, connected to the CPU water block and pump assembly.

പ്രധാന സവിശേഷതകൾ:

• AiO Water Cooling: High-performance, pre-assembled water cooling loop, ready to install and maintenance-free.
• PWM-Controlled Pump: Quiet pump block with ceramic bearings and PWM control for efficient cooling.
• Three Fluctus 120 PWM ARGB Fans: Optimized for high static pressure, providing superb performance on water radiators at low noise levels.
• ARGB LED Lighting: Backlit pump and fans with independently controlled ARGB LEDs for customizable lighting effects.
• Nano Reset ARGB Controller: Built-in lighting can be controlled by compatible motherboards or independently with the included Nano Reset ARGB controller.
• Kink-Resistant Rubber Hoses: Internally reinforced tubes are flexible and easy to route, with outer sleeves protecting the tubes and providing a uniform look.
• Multi-Socket Compatibility: Redesigned mounting system is easy to install and compatible with all modern AMD and Intel sockets.

ചിത്രം 2: The Navis F360 ARGB installed inside a computer case, demonstrating its compact fit and the vibrant ARGB lighting of the fans and pump. This setup highlights the cooler's ability to provide effective cooling in demanding conditions.

ചിത്രം 3: എ വിശദമായി view of the Fluctus 120 PWM ARGB fans, highlighting their serrated blade edge profile designed for quiet and efficient airflow. The image shows the pre-installed fans on the radiator.

ചിത്രം 4: Illustration of the PWM controlled pump and the 360-millimeter radiator, emphasizing the uncompromised cooling performance provided by these components, including the ceramic bearing in the pump.

ചിത്രം 5: The mesmerizing ARGB backlight of the Navis F360 ARGB, showcasing the vibrant illumination of the fans and water block pump. The image also indicates that color patterns can be adjusted via the Nano Reset ARGB driver without a direct motherboard connection.

ചിത്രം 6: An image illustrating the convenient and simple installation process of the Navis F360 ARGB. The integrated water block pump frame and 39 cm long flexible tubes allow for versatile placement within a computer case.

സ്പെസിഫിക്കേഷനുകൾ

സജ്ജീകരണവും ഇൻസ്റ്റാളേഷനും

ഇൻസ്റ്റാളേഷൻ ആരംഭിക്കുന്നതിന് മുമ്പ്, നിങ്ങളുടെ കമ്പ്യൂട്ടർ ഓഫ് ചെയ്തിട്ടുണ്ടെന്നും വാൾ ഔട്ട്‌ലെറ്റിൽ നിന്ന് പ്ലഗ് ഊരിയിട്ടുണ്ടെന്നും ഉറപ്പാക്കുക. ഘടകങ്ങൾക്ക് കേടുപാടുകൾ സംഭവിക്കാതിരിക്കാൻ ഒരു ആന്റി-സ്റ്റാറ്റിക് റിസ്റ്റ് സ്ട്രാപ്പ് ധരിക്കാൻ ശുപാർശ ചെയ്യുന്നു.

പാക്കേജ് ഉള്ളടക്കം:

• ENDORFY Navis F360 ARGB AIO Cooler (Radiator with 3x Fluctus 120 PWM ARGB fans, pump/cold plate assembly, tubing)
• Mounting hardware for Intel and AMD sockets
• Pactum PT-3 Thermal Compound (pre-applied or in tube)
• Nano Reset ARGB Controller
• ഉപയോക്തൃ മാനുവൽ (ഈ പ്രമാണം)

ചിത്രം 7: The included Pactum PT-3 thermal paste and applicator. This easy-to-apply thermal paste ensures excellent heat removal performance, and the tube provides enough for several installations.

ഇൻസ്റ്റലേഷൻ ഘട്ടങ്ങൾ:

1. മദർബോർഡ് തയ്യാറാക്കുക: Install the appropriate backplate for your CPU socket (Intel or AMD) onto the motherboard. Refer to your motherboard's manual for specific instructions on CPU and backplate installation.
2. റേഡിയേറ്റർ മൗണ്ട് ചെയ്യുക: Identify a suitable mounting location in your PC case for the 360mm radiator (e.g., top, front). The fans are pre-installed on the radiator for convenience. Secure the radiator to the case using the provided screws.
3. സിപിയു തയ്യാറാക്കുക: If thermal paste is not pre-applied to the cold plate, apply a small amount of the included Pactum PT-3 thermal compound to the center of your CPU's Integrated Heat Spreader (IHS).
4. പമ്പ്/കോൾഡ് പ്ലേറ്റ് ഇൻസ്റ്റാൾ ചെയ്യുക: Carefully align the pump/cold plate assembly with the mounting holes around your CPU socket. Gently lower the cold plate onto the CPU, ensuring even contact. Secure the pump assembly using the appropriate standoffs and thumb screws for your socket type. Tighten screws in a diagonal pattern until snug.
5. കേബിളുകൾ ബന്ധിപ്പിക്കുക:
   • പമ്പിന്റെ 4-പിൻ PWM കേബിൾ നിങ്ങളുടെ മദർബോർഡിലെ CPU_FAN അല്ലെങ്കിൽ AIO_PUMP ഹെഡറുമായി ബന്ധിപ്പിക്കുക.
   • Connect the fan's 4-pin PWM cable (from the daisy-chained fans) to a fan header on your motherboard or a fan controller.
   • Connect the ARGB cables from the pump and fans to the Nano Reset ARGB Controller. Then, connect the controller to a SATA power connector from your power supply. If your motherboard supports ARGB, you can connect the controller to a 3-pin 5V ARGB header on your motherboard for software control.
6. കേബിൾ മാനേജുമെന്റ്: ശരിയായ വായുസഞ്ചാരവും വൃത്തിയുള്ള നിർമ്മാണവും ഉറപ്പാക്കാൻ എല്ലാ കേബിളുകളും വൃത്തിയായി റൂട്ട് ചെയ്യുക.

For detailed visual guides and specific socket instructions, please refer to the official ENDORFY knowledge base: http://endorfy.com/kb/EY3B006

ഓപ്പറേഷൻ

Once installed, the ENDORFY Navis F360 ARGB operates automatically based on your motherboard's fan and pump control settings. The PWM (Pulse Width Modulation) functionality allows the pump and fans to adjust their speed according to CPU temperature, providing efficient cooling while minimizing noise.

ARGB ലൈറ്റിംഗ് നിയന്ത്രണം:

• Via Nano Reset ARGB Controller: If connected to the included Nano Reset controller, you can cycle through various lighting modes and colors by pressing the button on the controller.
• മദർബോർഡ് സോഫ്റ്റ്‌വെയർ വഴി: If the Nano Reset controller is connected to a compatible 3-pin 5V ARGB header on your motherboard, you can control the lighting effects using your motherboard's RGB software (e.g., ASUS Aura Sync, MSI Mystic Light, Gigabyte RGB Fusion, ASRock Polychrome Sync).

മെയിൻ്റനൻസ്

The ENDORFY Navis F360 ARGB is designed to be a maintenance-free AIO liquid cooler. The closed-loop system means you do not need to refill or replace the coolant.

ശുപാർശ ചെയ്യുന്ന പരിപാലനം:

• പൊടി വൃത്തിയാക്കൽ: Periodically inspect the radiator fins and fan blades for dust buildup. Use compressed air or a soft brush to gently remove dust. Excessive dust can impede airflow and reduce cooling performance.
• ഹോസ് പരിശോധന: Occasionally check the rubber hoses for any signs of kinks, leaks, or damage. While designed to be kink-resistant, ensuring they are not overly bent will prolong their lifespan.
• കണക്ഷൻ പരിശോധന: Ensure all power and signal cables remain securely connected to the motherboard, power supply, and ARGB controller.

ട്രബിൾഷൂട്ടിംഗ്

If you encounter issues with your ENDORFY Navis F360 ARGB, refer to the following common problems and solutions:

വാറൻ്റിയും പിന്തുണയും

The ENDORFY Navis F360 ARGB CPU Water Cooler comes with a 3 വർഷത്തെ നിർമ്മാതാവിന്റെ വാറന്റി from the date of purchase, covering defects in materials and workmanship. This warranty does not cover damage caused by improper installation, accident, abuse, misuse, natural disaster, or unauthorized modification.

For technical support, warranty claims, or further assistance, please visit the official ENDORFY support page or contact their customer service:

Webസൈറ്റ്: endorfy.com/contact

Please have your product model number (EY3B006) and proof of purchase ready when contacting support.